One for All Access 5 User Manual

Press VCR/DVD, AUX,
RCR/AMP, CBL/SAT, or
TV once to select a
home entertainment
device to control.
ACCESS 5
Use the keypad (0 ~ 9)
UNIVERSAL REMOTE CONTROL
to directly select
channels (for example,
09 or 31).
POWER
Press MUTE once to
turn sound off or on.
Press PREV once to
recall the last-viewed
channel and to page
back one screen on the
main menu.
Press ENTER once
after entering channel
numbers on some TVs.
Press SLEEP to activate
your device's sleep
timer (not available
REW FF
PLAY for all devices).
PAUSE STOP
Press SHIFT and use
the Up/Down/Left
Right cursor keys to
move the cursor in the
program guide and
menu screens.
Press SHIFT and MUTE
USER'S GUIDE
to select a menu item.
Use VOL+ (or VOL-)
to raise (or lower) the
sound volume.
L
Use CH
INTRODUCTION
select the next higher
(or lower) channel.
The One For All Access 5 Universal
Remote Control is designed to operate
When controlling a
five home entertainment devices, includ-
DVD/CD player, use
ing TV, video, and audio components.
SKIP FORWARD (or
SKIP REV) to skip to
The remote control requires two fresh
the next (or previous)
AAA alkaline batteries (not included) and
DVD chapter/CD track.
easy programming to control your devices.
For best results, please read and perform
Press MENU once to
all instructions listed here.Also, keep
display your selected
these instructions for future reference.
device's main menu.
Use EXIT to exit from
your selected device's
FEATURES AND FUNCTIONS
menu or guide.
Use the Key Charts to learn how to use the
Use GUIDE to display
universal functions of the One For All
your selected device's
Access 5 Universal Remote Control.
program guide.
Key Charts
Use INFO to display the
current channel and
Use SETUP for all
programming program information.
sequences.
Use the transport keys
REW FF to control your VCR,
The LED (red light)
PLAY
CD or DVD player, or
blinks to show that
PAUSE STOP
the remote control is VOD. To record a
program, press the
working and is
record key (
sending signals.
Press POWER once to Use TV/VID to switch
POWER
turn on or off the the TV's input to view
TV or video programs.
selected device.
INSTALLING BATTERIES PROGRAMMING
TV/VCR COMBO CONTROL
1. On the remote control's back, push the
tab and lift off the battery cover.
Perform the following instructions to
control a TV/VCR Combo:
2. Obtain two (2) fully-charged AAA
alkaline batteries. Match the + and –
1. Turn on the TV/VCR Combo and
marks on the batteries to the + and
– marks in the battery case, then
insert the new batteries.
3. Press the battery cover back into
place. The tab should click when the
cover is locked.
2. On the remote control, press VCR/DVD.
4. Test the unit by pressing POWER and
any mode key (e.g., TV). If batteries
are inserted correctly, the LED will
3. Use the Setup Codes For TV/VCR
blink once.
NOTE: When batteries need replacement,
the remote control will stop operating.
Remove the old batteries and insert new
ones within 10 minutes to ensure all of
your programming information is restored.
PROGRAMMING
4. Aim the remote control at the device
DEVICE CONTROL
The One For All Access 5 remote control
is preprogrammed at the factory to
operate an RCA TV and VCR, a Motorola
(GI) cable box, a Pioneer audio tuner,
and a Radio Shack X-10 home automa-
tion unit. To control devices other than
the default brands, perform the follow-
ing steps; otherwise skip this section:
NOTE: For TV/VCR Combo control, see the
next section. SEARCHING FOR YOUR CODE
1. Turn on a device (e.g.,VCR) and, if
M If your device does not respond to the
(or CH ) to
applicable, insert media, (e.g.,
remote control after trying all codes
cassette or disc).
listed for your brand, or if your brand is
not listed at all, try searching for your
NOTE: Please read steps 2-4 completely
before proceeding. Highlight or write down code. For example, to search for a code
the codes and device you wish to program for your TV:
before moving on to step 2.
1. On the remote control, press TV once.
2. On the remote control, press a
2. Press and hold SETUP until the LED
device key once (i.e., VCR/DVD, AUX,
RCR/AMP, CBL/SAT, or TV). Press and
hold SETUP until the LED blinks
3. Enter 9 - 9 - 1. The LED will
twice, then release SETUP.
3. Use the Manufacturer's Codes to
4. Aim the remote control at the the
locate the the type of device and
brand name and then enter the first
four-digit code for your device. If
performed correctly, the LED will
blink twice.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
5. To lock in the code, press and hold
4. Aim the remote control at the device
and press POWER once. The device
should turn off. If it does not respond,
6. To search for the codes of your other
repeat steps 2-3, trying each code for
your brand until you find one that
works. If it still does not work, try
Searching For Your Code.
) twice.
•
NOTE: If the device does not have a
POWER key, press the ( Play ) key.
5. Repeat steps 1 through 4 for each
device you want to control.
CHECKING THE CODES
If you have set up the remote control
using the Searching For Your Code
procedure, you may need to find out
which four-digit code is operating your
equipment:
insert a video cassette.
For example, to find out which code is
NOTE: Please read steps 2-4 completely
operating your TV:
before proceeding. Highlight or write down
the codes and device you wish to program
1. On the remote control, press TV once.
before moving on to step 2.
2. Press and hold SETUP until the LED
blinks twice, then release SETUP.
Press and hold SETUP until the LED
3. Enter 9 - 9 - 0. The LED will
blinks twice, then release SETUP.
blink twice.
4. To view the code for the first digit,
Combos (on the back side) to locate
press 1 once.Wait 3 seconds, count
the brand name and then enter the
the LED blinks (e.g., 3 blinks = 3)
first four-digit code for your device.
and write down the number.
If performed correctly, the LED will
blink twice.
NOTE: If a code digit is "0", the LED will
not blink.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
5. Repeat step 4 three more times for
the same code again.
remaining digits. Use 2 for the
second digit, 3 for the third digit,
and 4 for the fourth digit.
and press POWER once. It should turn
off. If the device does not respond,
6. To check for codes of other devices,
repeat steps 2-3, trying each code for
repeat steps 1 through 5, but substi-
your brand until you find one that
tute the appropriate device key for
works. If it still does not work, try
each device you are checking.
Searching For Your Code.
As before, write down each four-
digit code.
NOTE: If the device does not have a
POWER key, press the ( Play ) key.
RE-ASSIGNING DEVICE KEYS
The One For All Access 5 can be set to
control a second TV,VCR, DVD player, or
audio device.
For example, to control a TV, a cable box,
and two VCRs, you will need to re-assign
the unused AUX key to operate the sec-
ond VCR as follows:
1. On the remote control, press and
hold SETUP until the LED blinks
blinks twice, then release SETUP.
twice, then release SETUP.
2. Enter 9 - 9 - 2. The LED will
blink twice. blink twice.
3. Press VCR once, then press AUX once.
TV and slowly alternate between
4. The AUX key is now ready to be pro-
pressing POWER and TV. Stop when
grammed for your second VCR. See
the TV turns off.
Programming Device Control.
NOTE: In the search mode, the remote
To re-assign other device keys, repeat
control will send IR codes from its library
steps 1 through 4 by substituting the key
to the selected device, starting with the
sequence from the below chart for the
most popular code first.
most popular devices:
To Re-Assign Key
SETUP until the LED blinks twice,
then release SETUP. Sequence Perform
VCR/DVD as
devices, repeat steps 1 through 5, but 2nd TV key: SETUP - 9 - 9 - 2
- TV - VCR/DVD
substitute the appropriate device key
VCR/DVD as 2nd
for the device you are searching for.
CBL/SAT key: SETUP - 9 - 9 - 2
-CBL/SAT - VCR/DVD
VCR/DVD as 2nd
RCR/AMP key: SETUP - 9 - 9 - 2
-RCR/AMP- VCR/DVD
VCR/DVD back to TROUBLESHOOTING
VCR/DVD: SETUP - 9 - 9 - 2
-VCR/DVD - VCR/DVD
For assistance, please contact us in any
RCR/AMP as
of the following ways:
2nd TV key: SETUP - 9 - 9 - 2
• Consumer Help Line: (330) 405-8612
- TV - RCR/AMP
RCR/AMP as 2nd
• Internet: http://www.oneforall.com
VCR/DVD key: SETUP - 9 - 9 - 2
- VCR/DVD-RCR/AMP
RCR/AMP as 2nd
PROBLEM: LED does not blink when
CBL/SAT key: SETUP - 9 - 9 - 2
-CBL/SAT - RCR/AMP you press a key.
RCR/AMP back to
SOLUTION: Replace batteries with two
RCR/AMP: SETUP - 9 - 9 - 2
new AAA alkaline batteries.
-RCR/AMP-RCR/AMP
AUX as
PROBLEM: LED blinks when you
2nd TV key: SETUP - 9 - 9 - 2
press a key, but home
- TV - AUX
entertainment device
AUX as 2nd
does not respond.
VCR/DVD key: SETUP - 9 - 9 - 2
- VCR/DVD- AUX
SOLUTION: Make sure the remote
AUX as 2nd
control is aimed at your
CBL/SAT key: SETUP - 9 - 9 - 2
home entertainment
-CBL/SAT - AUX
device and is not farther
AUX back to
than 15 feet away.
AUX: SETUP - 9 - 9 - 2
-AUX- AUX
PROBLEM: The unit does not control
home entertainment
When a re-assignment is done, the LED
devices or commands are
will blink twice to confirm your choice.
not working properly.
At that time, you will need to program
the remote control for the new device
SOLUTION: Try all listed codes for the
(see Programming Device Control).
device brands being
set up. Make sure they
can be operated with an
CHANGING VOLUME LOCK
infrared remote control.
The One For All Access 5 is set to PROBLEM: TV/VCR combo does not
control the volume of your TV in the TV, respond properly.
VCR/DVD, CBL/SAT, RCR/AMP, and
SOLUTION: Use the VCR codes for
AUX modes. If you want volume to be
your brand. Some combo
controlled by a mode other than TV
units may require both a
(e.g., CBL/SAT), change the Volume Lock
TV code and a VCR code
setting as follows:
for full operation.
To Change Volume Lock To Be
PROBLEM: Changing channels does
Controlled By Another Mode:
not work properly.
1. On the remote control, press and
SOLUTION: If original remote control
hold SETUP until the LED blinks
required pressing ENTER
twice, then release SETUP.
to change channels, press
ENTER on the remote
2. Enter 9 - 9 - 3 and then press any
control after entering the
mode key once (except TV). The LED
channel number.
will blink twice.
PROBLEM: Tried "Search Method"
3. Now, whenever you press VOL+,
and still could not find a
VOL–, or MUTE, volume will be
working code.
controlled by your mode choice.
SOLUTION: Clear the device key as
Unlocking Volume Control:
follows: Press and hold
NOTE: Perform these instructions when you
SETUP until the LED
want independent volume control for each
blinks twice, then release.
programmed device (e.g., TV volume control
Next enter 9 - 9 - 2. Then
in TV mode, CBL/SAT volume in CBL/SAT
press the device key to be
mode, etc.)
cleared twice. Now repeat
1. On the remote control, press and
the "Search Method. "
hold SETUP until the LED blinks
PROBLEM: Remote control does not
twice, then release SETUP.
turn on Sony or Sharp
2. Enter 9 - 9 - 3 and then press VOL+.
TV/VCR Combo.
The LED will blink four times.
SOLUTION: For power on, these prod-
3. Volume will again be controlled
ucts require programming
according to its default states.
TV codes. For Sony, use
TV code 0000 and VCR
code 0032. For Sharp, use
TV code 0093 and VCR
code 0048.
CH L and CH M
PROBLEM: do not
work for your RCA TV.
SOLUTION: Due to RCA design (1983-
1987), only the original
remote control will oper-
ate these functions.
MANUFACTURER'S CODES
Setup Codes For Audio Amplifiers
Aiwa 0406
Bose 0674
Carver 0269
Curtis Mathes 0300
Denon 0160
GE 0078
Harman/Kardon 0892
JVC 0331
Linn 0269
Luxman 0165
Magnavox 0269
Marantz 0269, 0892, 0321
Nakamichi 0321
Optimus 0300, 0395
Panasonic 0308
Parasound 0246
Philips 0269, 0892
Pioneer 0013, 0300
Polk Audio 0269, 0892
RCA 0300
Realistic 0395
Sansui 0321
Sony 0220, 0689
Soundesign 0078, 0211
Technics 0308, 0521
Victor 0331
Wards 0013, 0078, 0211
Yamaha 0354
Setup Codes For Audio Tuners
ADC 0531
Adcom 0616, 0002, 0304
Admiral 0182
Aiwa 1089, 1405, 0158, 0189, 0121, 0405,
0125
Akai 0224, 0076
Bose 0639
Capetronic 0531
Carver 1089, 1189, 0189, 0042, 0360, 0008,
0412
Casio 0195, 0201
Clarinette 0195
Curtis Mathes 0080, 0201
Denon 1104, 1160, 0004, 0273, 0771
Emerson 0424, 0255
Fisher 0042, 0360, 0219
GE 0260
Garrard 0463, 0424, 0146, 0281, 0440, 0744
Hafler 0146
Harman/Kardon 0110, 0189, 0891
Hitachi 0228
Inkel 0062, 0066
JBL 0110
JVC 0074, 0464
Kenwood 1313, 1027, 1570, 1569, 0027, 0186,
0042, 0077, 0313, 0314, 0569
Koss 0424, 0255, 0744
LXI 0181, 0744
Lexicon 1076
Linn 0189
Lloyd's 0195
Luxman 0166
MCS 0039, 0346, 0201
Magnavox 1089, 1189, 0531, 0189, 0195, 0391,
0128, 0222, 0204, 0364
Marantz 1089, 1189, 0039, 0189, 0128, 0200,
0006, 0412
Modulaire 0195
NAD 0320
NEC 0235
NTDE Geniesom 0744
Nakamichi 0097, 0347
Onkyo 0135, 0100, 0380, 0119
Continued on back...