Pc Connector; Slot Cover - Sony PMW-320K Operating Instructions Manual

b PC connector
Used to put this camcorder into USB connection
mode and use it as an external storage device for
a computer. When a computer without
ExpressCard slot is connected to this connector,
every memory card inserted in the camcorder is
recognized as a drive for that computer.
c External device connector
Connect an optional CBK-WA01 Wi-Fi Adapter.
Connecting a CBK-WA01 allows Wi-Fi
connection (wireless LAN connection) between
the camcorder and a computer.
Notes
• When you connect a CBK-WA01, install the optional
CBK-UPG02 Hardware Upgrade Key.
• Use this connector only for connecting a CBK-WA01.
Do not connect and use a USB hub or similar products.
For details on how to use the CBK-WA01, refer to the
Supplement supplied in the CD-ROM (labeled
"Manuals for Solid-State Memory Camcorder").
d SxS memory card slots
These two slots (A and B) can receive SxS
memory cards or other recording media (see
page 67).
e ACCESS lamps
Indicate the state of slots A and B (see page 67).
You can check whether the lamps are lit even
when the slot cover is closed.
f EJECT buttons
To remove the recording media from the slot,
press the EJECT button to release the lock, then
press the button once more. This makes the media
come out of the slot partially (see page 68).
g Slot cover
Slide to the left and right to open and close.
h SLOT SELECT (SxS memory card
select) button
When SxS memory cards are loaded in both card
slots A and B, press this button to select the card
you want to use (see page 68).
i HDMI
1)
output connector
Outputs HDMI signals for video monitoring.
When a video monitor provided with an HDMI
signal input connector is connected to this
24
Locations and Functions of Parts and Controls
connector, you can monitor picture being shot
(camera picture) or playback picture.
1) The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
j GENLOCK IN (genlock signal input)
connector (BNC type)
This connector inputs a reference signal when the
camcorder is to be genlocked or when timecode is
to be synchronized with external equipment.
Available reference signals vary depending on the
current system frequency as shown in the
following table.
System frequency Available reference signals
1080/59.94i 1080/59.94i, 480/59.94i
1080/29.97P 1080/59.94i, 480/59.94i
1080/23.98P (PsF 1080/23.98PsF, 480/59.94i
output)
1080/23.98P 1080/59.94i, 480/59.94i
(Pulldown output)
720/59.94P 1080/59.94i, 720/59.94P,
480/59.94i
720/29.97P 1080/59.94i, 720/59.94P,
480/59.94i
720/23.98P 1080/59.94i, 720/59.94P,
480/59.94i
480/59.94i 1080/59.94i, 480/59.94i
480/29.97P 1080/59.94i, 480/59.94i
1080/50i 1080/50i, 576/50i
1080/25P 1080/50i, 576/50i
720/50P 1080/50i, 720/50P, 576/50i
720/25P 1080/50i, 720/50P, 576/50i
576/50i 1080/50i, 576/50i
576/25P 1080/50i, 576/50i
(Genlock for the camera module supports
horizontal sync signals only.) Use
MAINTENANCE >GENLOCK in the setup
menu to adjust the genlock H-phase (phase of
horizontal sync signal).
k TC IN (timecode input) connector
(BNC type)
To apply an external lock to the timecode of the
camcorder, input the reference timecode.
For details, see "Setting the Timecode" (page 62).