AT&T CRL82112 Quick Start Manual

Quick start guide
CRL82112/CRL82212/CRL82312/CRL82352/CRL82412/CRL82452
This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user's
manual provided in the package, or see the online Complete
user's manual at www.telephones.att.com/manuals.
Telephone base installation
Plug the power cord
Route the
and telephone line
cords through
cord into the jacks.
the slot.
Raise the
antenna.
If you have DSL
high-speed Internet
Plug the other end
service, a DSL
filter (not included)
of the telephone
is required. The
line cord into a
DSL filter must be
telephone jack or
plugged into the
a DSL filter.
telephone wall jack.
Caution: Use only the power adapter(s) provided with this product. To obtain a replacement,
www.telephones.att.com
visit our website at
1 (866) 288-4268
In Canada, dial .
Battery installation
Install the battery as shown below. Charge your handset(s) before initial use.
The battery is fully charged after 10 hours of continuous charging.
1 2
1. Plug the battery 2. Align the cover
connector securely flat against
into the socket inside the battery
the handset battery compartment,
compartment. Insert the then slide it
supplied battery with upwards until it
the label THIS SIDE UP clicks into place.
facing up as indicated.
Use only the supplied rechargeable battery or replacement battery (model BT183342).
Quick reference guide
CHA�GE indicator
On when the handset is charging
in the telephone base or charger.
q
CID/VOLUME
• Show caller ID history.
• Scroll down in menus.
Charger installation
• Move cursor to the left when
entering names or numbers.
• Decrease listening volume when
on a call, or decrease message
playback volume.
�EDIAL/PAUSE
• Press repeatedly to view the last
10 numbers dialed.
• Press and hold to insert a dialing
pause while entering numbers.
PHONE/FLASH
• Make or answer a call.
• Answer a call waiting call during
a call.
1
• Press repeatedly to add or
remove 1 in front of the call log
Plug the power
entry before dialing or saving it
adapter into an
to the directory.
electrical outlet • Press and hold to set or dial your
voicemail number.
not controlled by
a wall switch.
TONE
Press to switch to tone dialing
temporarily during a call if you
have pulse service.
1 (800) 222-3111
or call .
/SPEA�E� SPEA�E�
Switch between the speakerphone
and handset.
3
/ANSWE� ON
Turn the built-in answering
system on or off.
Message counter
3. Charge the handset by
Shows the number
of messages or other
placing it face forward
answering system
in the telephone base
information.
or charger.
/�EPEAT
• Repeat a message.
• Press twice to play the
previous message.
Audio Assist ® is a registered trademark of Advanced American Telephones.
pDI�/VOLUME
• Show directory entries.
Handset
• Scroll up in menus.
• Move cursor to the right when
entering names or numbers.
• Increase listening volume when
on a call, or increase message
playback volume.
MENU/SELECT
• Show the menu.
• Select an item or save an entry
or setting while in the menu.
OFF/CANCEL
• Hang up a call.
• Press to cancel an operation,
back up to the previous
menu, or exit the menu display,
or press and hold to return to
idle mode.
• Press and hold in idle mode to
erase missed call indicator.
QUIET # (pound key)
• Press repeatedly to display
other dialing options when
reviewing a caller ID log entry.
• Press and hold to enter the
QUIET mode setting screen, or
to deactivate QUIET mode.
®
AUDIO ASSIST
Voices will sound louder and
clearer when you press
®
AUDIO ASSIST
on a call using the handset.
MUTE/DELETE
• Mute the microphone during a call.
• Delete the displayed entry while in the
directory, call log or redial list.
• Delete digits or characters when using
the dialing keys.
EQ
Handset
Change the audio quality to best
side view
suit your hearing.
Telephone base
X/DELETE
• Delete the message
currently playing.
• Press twice to delete
all old messages when
in idle mode.
q/VOL/p
• Adjust the listening
volume during
message playback.
• Adjust the base ringer
volume when in idle
mode.
/PLAY/STOP
/S�IP
Start or stop message
Skip to the next message.
playback.
Initial settings
We recommend you program your telephone system before use.
The following are a few examples of common features to set before using the
telephone. Refer to the Handset settings and Answering system settings in
the Abridged user's manual or the online Complete user's manual for detailed
instructions on setting all telephone features.
Set date/time
Set the date/time before using the answering system.
1. MENU -> q or p -> Set date/time -> SELECT.
2. Enter the month, day and year using the dialing keys -> SELECT.
3. Enter the hour and minute using the dialing keys.
4. q or p to choose AM or PM -> SELECT.
Record your own announcement
Your outgoing announcement plays when calls are answered by the answering
system. You can use the default announcement to answer calls, or replace it
with your own recorded announcement.
1. MENU -> q or p -> Answering sys -> SELECT.
2. SELECT to select Announcement.
3. SELECT to select �ecord annc.
4. Facing the handset, record your announcement and press 5 to end recording.
Number of rings
You can set the answering system to answer an incoming call after two, three,
four, five or six rings, or toll saver. If you choose toll saver, the answering
system answers a call after two rings if you have new messages, or after four
rings when there are no new messages.
If you want the built-in answering system instead of the voicemail to answer a
call, you should set the answering system to answer a call at least two rings
before the voicemail is set to answer. Contact your telephone service provider
for information on your voicemail settings.
while you are
MENU -> q or p -> Answering sys -> SELECT.
1.
2. q or p -> Ans sys setup -> SELECT.
3. q or p -> # of rings -> SELECT.
4. q or p -> choose among 2, 3, 4, 5, 6 or Toll saver -> SELECT.
Handset ringer volume
You can set the ringer volume level to one of the six levels or turn the
ringer off.
1. MENU -> q or p -> �ingers -> SELECT.
2. SELECT to select �inger volume.
3. q or p to choose the desired level -> SELECT.
Reset language to English
If you have accidentally changed the screen display language and want to
switch it back to English, follow the steps below.
• MENU in idle mode-> enter 364#.