Box camera iii;
dome camera iii;
dome camera iv;
dome camera v;
dome camera vi;
dome camera vii;
bullet camera i;
bullet camera ii;
bullet camera iii;
bullet camera iv;
cube camera i;
cube camera ii;
mini dome camera (37 pages)
Network Camera Installation Manual V5.0 Hangzhou Hikvision Digital Technology Co., Ltd. http://www.hikvision.com UD.6L0201A1008A01...
Page 2
Installation Manual of Network Camera Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. variety of There is structures of network cameras in our company. Installing instructions of all these cameras are listed in this manual.
Page 3
Installation Manual of Network Camera This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual. DISCLAIMER STATEMENT “Underwriters Laboratories Inc.
Installation Manual of Network Camera Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Page 5
Installation Manual of Network Camera Notice: Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.
Installation Manual of Network Camera Chapter 1 Introduction The network camera is a kind of embedded digital surveillance product that combines the features of both traditional analog camera and net DVS (Digital Video Server). With a built-in video server, the network camera is capable of providing real-time video stream compression, processing, video analysis and transmission simultaneously.
Installation Manual of Network Camera Chapter 2 Box Camera Installation 2.1 Appearance Description 2.1.1 Box Camera I Camera description: Figure 2-1 Overview Description Table 2-1 Description Lens mount Back focus ring SD card slot Auto-iris interface 10M/100M self-adaptive Ethernet interface VIDEO OUT: Video output interface AUDIO OUT: Audio output interface POWER: Power LED indicator...
Page 10
Installation Manual of Network Camera Notes: To reset the default parameters to the camera, you need to press and hold the RESET button and power on the camera. After the power on of the camera, you must still press and hold the Reset button for about 20 seconds.
Installation Manual of Network Camera Figure 2-3 Wiring Diagram 2.2 Installation Box camera I, II, III can be installed to wall or ceiling. Ceiling mounting is taken as an example in this section; if you adopt wall mounting, you can also take the below procedure as a reference. 2.2.2 Lens Installation Steps: 1.
Installation Manual of Network Camera keyboards. Grounding The ground screw can be connected for grounding. 2.2.4 Mounting Before you start: These box cameras can be installed to wall or ceiling. Wall mounting is taken as an example in this section;...
Installation Manual of Network Camera Figure 2-7 Mount the Camera Note: This camera is designed for indoor and outdoor use. To use the camera outdoors, it must be installed in an approved outdoor housing as shown in Figure 2-8. Figure 2-8 Wall Mounting with the Housing 4.
Page 14
Installation Manual of Network Camera Figure 2-10 Tilting...
Installation Manual of Network Camera Figure 3-2 Wiring Diagram 3.1.2 Installation Ceiling mounting: Note: If required, you can use a plier to remove the clip (one or two) on the side of the back box and then route cables through the opening to secure the cables on the ceiling. Figure 3-3 Remove the Clip Steps: 1.
Page 17
Installation Manual of Network Camera Figure 3-4 Mount the Camera 2. Loosen the set screws with the hex key (supplied) to remove the lower dome. Figure 3-5 Remove the Lower Dome 3. Connect the RCA analog video output with a monitor to view the image of the camera. Loosen the lens set screw and pan, tilt or rotate the lens to get a desired surveillance angle.
Page 18
Installation Manual of Network Camera 4. Reinstall the lower dome and tighten the screws. Figure 3-7 Reinstall the Lower Dome In-ceiling mounting: Steps: 1. Secure the mounting base to the in-ceiling mounting base with screws. Figure 3-8 Secure the Mounting Base 2.
Page 19
Installation Manual of Network Camera Figure 3-9 Fix the Camera 3. Cut a 176~180 mm diameter hole in the ceiling and push the dome camera with in-ceiling mounting base to the hole. Note: The thickness of the ceiling should be less than 30 mm. Figure 3-10 Mount the Camera 4.
Page 20
Installation Manual of Network Camera Figure 3-11 Safety rope 5. Fasten the lock screws to secure the dome camera. Figure 3-12 Secure the Camera 6. Remove the lower dome and connect the RCA analog video output with a monitor to view the image of the camera.
Installation Manual of Network Camera Figure 3-15 Overview Description Table 3-2 Description Video output interface LINK: Indicator is solid yellow when network is connected. ACT: Indicator flashes blue when network connection is functioning properly. PWR: Indicator is solid red when the device is powered on. Micro SD slot RESET: Reset button 10M/100M self-adaptive Ethernet interface...
Page 23
Installation Manual of Network Camera Figure 3-17 Drill Template 2. Secure the back box to the ceiling with screws. Figure 3-18 Mount the Back Box 3. Loosen the set screws with the hex key (supplied) to remove the lower dome; remove the dome liner.
Page 24
Installation Manual of Network Camera Figure 3-19 Remove the Lower Dome 4. Install the dome module to the back box and pull the cables through the cable outlet on the bottom of the back box. Figure 3-20 Mount the Camera Note: If you need to pull the cable through the cable outlet from the side of the camera, please remove the cover and use water-proof joints and water-proof pipe to route the cables.
Page 25
Installation Manual of Network Camera Figure 3-21 Route Cable through Side Outlet 5. After connecting the network cable and power cable, view the image of the camera over the network. Loosen the lock screws; adjust the panning position and tilting position and rotate the lens to get the desired surveillance angle;...
Page 26
Installation Manual of Network Camera Figure 3-23 Reinstall the Lower Dome In-ceiling mounting: Steps: 1. Drill the screw holes on the ceiling with the supplied drilling template. Figure 3-24 Drill Screw Holes 2. Cut the mounting holes on the ceiling with the supplied drilling template.
Page 27
Installation Manual of Network Camera Figure 3-25 Cut Mounting Hole 3. Loosen the set screws with the hex key (supplied) to remove the lower dome; remove the dome liner. Figure 3-26 Remove the Lower Dome 4. Rotate the toggle to remove it from the toggle bolt; insert the bolt into the toggle bolt hole on the dome module and use the screw driver to rotate the bolt slightly but not tightly;...
Page 28
Installation Manual of Network Camera Figure 3-27 Mount the Camera 5. Fasten the toggle bolt and the toggle will automatically secure the dome module to the ceiling. Figure 3-28 Fasten the Bolts 6. After connecting the network cable and power cable, view the image of the camera over the network.
Page 29
Installation Manual of Network Camera Figure 3-29 Adjust Image 7. Reinstall the dome liner and lower dome to finish the installation.
Page 30
Installation Manual of Network Camera Figure 3-30 Reinstall Wall mounting: Steps: 1. Drill the screw holes on the wall with the supplied drilling template. If you need to route the cables from the bottom of the camera, cut a cable hole in the wall. Figure 3-31 Drill Template 2.
Page 31
Installation Manual of Network Camera Figure 3-32 Secure the Back Box 3. Loosen the set screws with the hex key (supplied) to remove the lower dome; remove the dome liner. Figure 3-33 Remove the Lower Dome 4. Install the dome module to the back box and pull the cables through the cable outlet on the bottom of the back box.
Page 32
Installation Manual of Network Camera Figure 3-34 Route Cable through Side Outlet 5. After connecting the network cable and power cable, view the image of the camera over the network. Loosen the lock screws; adjust the panning position and tilting position and rotate the lens to get the desired surveillance angle;...
Page 33
Installation Manual of Network Camera Figure 3-35 Adjust Image 6. Reinstall the dome liner and lower dome to finish the installation. Outdoor mounting: You can use DS-1242ZJ or DS-1243ZJ for outdoor mounting. DS-1242ZJ DS-1243ZJ Steps: 1. Remove the front panel and secure the bracket to the wall or ceiling. 2.
Page 34
Installation Manual of Network Camera Figure 3-37 Secure the Camera 4. Fasten the toggle bolt and the toggle will automatically secure the dome module to the bracket. 5. After connecting the network cable and power cable, view the image of the camera over the network.
Page 35
Installation Manual of Network Camera Figure 3-38 Adjust Image 6. Reinstall the dome liner and lower dome. Figure 3-39 Reinstall the Lower Dome 7. Reinstall the front panel to finish the installation.
Installation Manual of Network Camera Figure 3-40 Reinstall the Front Panel 3.3 Dome Camera III 3.3.1 Overview Figure 3-41 Product Structure Diagram Table 1-1 Description Name Description 10M/100M self-adaptive Ethernet interface Connect to the network; PoE Power Cable Connect to the 12V DC Trim Ring Protect the camera Camera...
Page 37
Installation Manual of Network Camera Note: Please make sure that the power adapter is compatible with the camera. This series of camera supports Power over Ethernet (PoE), and the standard power supply is 12V DC.
Installation Manual of Network Camera 3.3.2 Installation Before you start, please verify the package contents are correct by checking the items against the packing list, and make sure all the components are included. Wall mounting is preferred. We will take wall mounting as an example to explain the installation steps in this section.
Page 39
Installation Manual of Network Camera There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below. Figure 3-44 Side Outlet Note: Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling.
Page 40
Installation Manual of Network Camera Figure 3-46 Lock Screw Figure 3-47 Adjust the Lens 5. Install the Trim Ring Attach the trim ring to the camera. Rotate the trim ring clockwise to secure it to the camera.
Installation Manual of Network Camera 3.4.3 Overview Figure 3-50 Overview Physical Description Table 3-3 Description Mounting base Horizontal stand Vertical stand Lower dome Cables Plate of infrared lamp Lens Black Liner Safety rope 3.4.4 Installation Notes: Read the following contents carefully before the installation. ...
Page 43
Installation Manual of Network Camera Do not place the camera in extremely hot or damp environment. To avoid heat accumulation, good ventilation is required for a proper operating environment. If the product does not function properly, please contact your dealer or the nearest service center.
Page 44
Installation Manual of Network Camera 3. Fix the mounting base on the ceiling with screws. Figure 3-53 Fix the Mounting Base Note: If required, you can route cables through the side opening on the side of the mounting base. Figure 3-54 Side Opening 4.
Installation Manual of Network Camera Figure 3-56 Reinstalling 3.5 Dome Camera V 3.5.5 Overview Figure 3-57 Overview Table 1-2 Physical Description Description Ceiling mount Lock button Mounting base SD card slot Description Lens...
Installation Manual of Network Camera Infrared lamp Lower dome Status indicator RCA analog video output Debug Reset Note: After the power-on of the camera, pressing and holding the RESET button for about 10 seconds can reset all the parameters to the default settings. 3.5.6 Installation Notes: ...
Page 47
Installation Manual of Network Camera Figure 3-59 Fix the Ceiling Mount 3. Route the cables through the cable hole on the ceiling. Note: If required, you can rotate to remove the side cover on the mounting base and route the cables through the side outlet.
Page 48
Installation Manual of Network Camera Figure 3-61 Install the Dome Camera Note: To uninstall the dome camera, press the lock screw and rotate the mounting base counterclockwise. Figure 3-62 Uninstall the Dome Camera 5. Loosen the set screws with a hex key (supplied) to remove the lower dome. Figure 3-63 Remove the Lower Dome 6.
Installation Manual of Network Camera 7. Reinstall the lower dome and tighten the screws. Figure 3-65 Reinstallation 3.6 Dome Camera VI 3.6.7 Overview Figure 3-66 Reinstallation...
Installation Manual of Network Camera Table 1-3 Overview Description Lower Dome Black Liner Reset Button AUX Video Output Interface Serial Port Power interface Ethernet interface Mounting Base Lens Notes: To reset the default parameters to the camera, you need to press and hold the reset button and power on the camera.
Page 51
Installation Manual of Network Camera Check the specification of the products for the installation environment. Make sure that all the related equipment is power-off during the installation. Check whether the power supply is matched with your AC outlet to avoid any damage. ...
Page 52
Installation Manual of Network Camera Cable Hole Drill Template Screw Hole Figure 3-69 The Drill Template 4. If you want to route the cables inside the ceiling, drill a cable hole in the ceiling according to the drill template. Skip this step, if you want to route the cables on the surface of the ceiling. Refer to Conduit Installation on the Side for side cable routing.
Page 53
Installation Manual of Network Camera 11. Install the lower dome back to the camera and secure it with screws as shown in Figure 2-4. Figure 3-71 Secure Black Liner and Lower Dome Conduit Installation on the Side If you want to route the cables from side of the camera, you need to follow the steps below to install a conduit for cable routing.
Installation Manual of Network Camera 2. Route the power cable and network cable through the side outlet to the conduit. 3. Align and rotate clockwise the conduit to the side outlet tightly. Conduit Figure 3-73 Install the Conduit to the Camera Note: For wall mounting, position the side outlet directly downward for water proofing.
Page 55
Installation Manual of Network Camera 1. Disassemble the camera. Refer to the section 2.1. 2. Install the gang box in the ceiling. 3. Attach the mounting base to the gang box with two screws. Mounting Base Screw Hole Screw Hole Figure 3-75 In-ceiling Mount Figure 2-8 In-ceiling Mount 4.
Page 56
Installation Manual of Network Camera Figure 3-76 Secure Camera 9. Install the inner black liner back to the camera. 10. Align the lower dome with the camera. 11. Tighten the screws to secure the lower dome with the camera as shown in Figure 2-7.
Page 57
Installation Manual of Network Camera Figure 3-77 Secure Lower Dome 2.2.3 Wall Mounting For the wall mounting, you have to purchase a wall mount. Steps: 1. Disassemble the camera. 2. Install the wall mount and mounting adapter. 3. Align the screw holes of the mounting base with the corresponding screw holes of the mounting adapter.
Page 58
Installation Manual of Network Camera Mounting Adaptor Figure 3-78 Install the Mounting Adapter...
Page 59
Installation Manual of Network Camera Mounting Base Figure 3-79 Secure Mounting Base 5. Route the cables through the hole in the center of the wall mount. 6. Align the camera with the mounting base. 7. Tighten the set screws to secure the camera with the mounting base. 8.
Page 60
Installation Manual of Network Camera Camera Figure 3-80 Secure Camera 10. Install the inner black liner back to the camera. 11. Align the lower dome with the camera. 12. Tighten the screws to secure the lower dome with the camera.
Installation Manual of Network Camera Black Liner Lower Dome Figure 3-81 Secure Black Liner and Lower Dome Image and Focus Adjusting Steps: 1. Three-axis adjustment. 1) View the camera image using the monitor. 2) Rotate the panning table to adjust the panning position of the camera. 3) Rotate the tilting axes to adjust the tilting position of the camera.
Page 62
Installation Manual of Network Camera Panning Tilting Rotation Figure 3-82 Three-axis Adjustment 2. Zoom and focus adjustment. 1) View the camera image using the monitor. 2) Loosen the zoom lever and move the lever between T(Tele) and W(Wide) to obtain the appropriate angle of view.
Page 63
Installation Manual of Network Camera Lever Lever Figure 3-83 Lens Adjustment...
Installation Manual of Network Camera Figure 4-3 Wiring Diagram 4.1.2 Installation Bullet camera can be installed to wall or ceiling. Wall mounting is taken as an example in this section; if you adopt ceiling mounting, you can also take below procedure as a reference. Steps: 1.
Page 66
Installation Manual of Network Camera Note: The “bottom” mark on the mounting base should align with the “bottom” mark on the mounting bracket. Figure 4-5 Secure the Camera 3. View the image of the camera over the network. 4. Loosen the screws on the bracket slightly. Note: Please loosen the screws slightly until you can adjust the camera and do not remove the screws from the bracket.
Installation Manual of Network Camera Figure 4-8 Adjust the Lens 8. Fix the lens; reinstall the front cover and the sun shield to finish the installation. Note: Reinstall the front cover until aligning the mark on the front cover with the mark on the camera. Figure 4-9 Reinstall the Camera 4.2 Bullet Camera II 4.2.1 Appearance Description...
Installation Manual of Network Camera Figure 4-11 Overview Table 4-2 Description Description 10M/100M self-adaptive Ethernet interface Power supply Sun shade Adjusting screw 4.2.2 Installation These bullet cameras can be installed to wall. Please refer to the steps below for installation. Steps: 1.
Page 69
Installation Manual of Network Camera Figure 4-13 Mount the Camera 4. Loosen the panning lock screw, you can adjust the panning angle of the camera up to 360° (Figure 2-9); Loosen the tilting lock screw, you can adjust the tilting angle of the camera up to 90° (Figure 2-10). Figure 4-14 Panning Figure 4-15 Tilting...
Installation Manual of Network Camera 4.3 Bullet Camera III 4.3.3 Appearance Description Figure 4-16 Bullet Camera Overview Sun Shield Back Box Grounding Screw Adjustable Bracket Reset Figure 4-17 Product Structure Diagram 4.3.4 Installation Note: Please make sure that the ceiling is strong enough to withstand three times the weight of the camera and the housing.
Page 71
Installation Manual of Network Camera The Ceiling Expansion Screw Figure 4-18 Secure the Camera to the Ceiling 2. Three-Axis Adjustment Loosen the adjusting nuts on the bracket, and adjust the camera from P/R/T direction. P Direction: 0~360°adjustable. T Direction: 0~90°adjustable. R Direction: 0~360°adjustable Adjust the lens to the surveillance angle.
Installation Manual of Network Camera 4.4 Bullet Camera IV 4.4.5 Appearance Figure 4-20 Product Structure Diagram Name Description Sun Shield Protection the camera Lock Screw Secure the sun shield Cables Power/Video Cable 4.4.6 Installation Before you start, please verify the package contents are correct by checking the items against the packing list, and make sure all the components are included.
Page 73
Installation Manual of Network Camera Secure the wall mount to the wall with the screws. Note: If the wall is the cement wall, you need to insert the expansion screws before you install the wall mount. If the wall is the wooden wall, you can use self-tapping screw to secure the wall mount. Figure 4-22 Secure the Wall Mount 3.
Installation Manual of Network Camera 4.5 Bullet Camera V 4.5.1 Appearance Figure 4-24 Overview Description Sun Shield Front Cover Zoom and Focus Lever IR LED Lens Air Vent Video Output Interface Integrated Bracket Reset Button SD Card Slot Power Interface Network Interface Notes:...
Installation Manual of Network Camera To reset the default parameters to the camera, you need to press and hold the reset button and power on the camera. After the power on the camera, you must still press and hold the reset button for about 10 seconds.
Page 76
Installation Manual of Network Camera Figure 4-26 Disassemble the Camera 4. Insert the SD card to the SD card slot. 5. Rotate the front cover clockwise back to the camera and install the sun shield according to the arrow direction as shown in Figure 4-27(right). SD Card Slot Figure 4-27 Install the SD Card 6.
Installation Manual of Network Camera Rotating Label Figure 4-28 Assemble the Camera Note: For water-proof, please align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise. Refer to Figure 4-28(right). Mounting This camera is equipped with a bracket on the bottom.
Page 78
Installation Manual of Network Camera Screw Hole Cable Hole 2:Screw Hole 1:Screw Hole for Mounting for Bracket Base Figure 4-29 Drilling Holes in the Wall 3. If you need to route cables through the wall (or ceiling), cut a cable hole according to the drill template.
Page 79
Installation Manual of Network Camera Figure 4-30 Secure the Camera Wall Mounting with a Junction Box Before you start: For mounting with a junction box, you have to purchase a junction box. Steps: 1. Attach the drill template (supplied) to the wall where the camera is to be mounted. 2.
Page 80
Installation Manual of Network Camera Safety Rope Junction Box Figure 4-31 Secure the Camera Wall Mounting with a Gang Box Before you start: For mounting with a gang box, you have to purchase a gang box. Steps: 1. Secure the camera attachment to a gang box with screws. 2.
Page 81
Installation Manual of Network Camera View Angle Adjusting Purpose: 3-axis (pan/tilt/rotation) adjusting allows adjustment for optimum camera rotation and placement. You can use this function to get the angle of view that you want. Pan Adjustment Steps: 1. Loosen the lock screw-1. 2.
Installation Manual of Network Camera 1. Disassemble the camera. Refer to section 2.1. 2. View the camera image using the monitor. 3. Loosen the zoom lever and move the lever between T(Tele) and W(Wide) to obtain the appropriate angle of view. 4.
Installation Manual of Network Camera 5.1 Cube Camera I 5.1.1 Appearance Description Camera description: Figure 5-1 Overview Description Table 5-1 Description Microphone Infrared light (Optional) Micro SD card slot LINK: Network status LED indicator. LED indicator is solid yellow when network connection is functioning properly.
Installation Manual of Network Camera Figure 5-2 Wiring Diagram 5.1.2 Installation The cube camera can be installed to wall or ceiling. Ceiling mounting is taken as an example in this section; if you adopt wall mounting, you can also take below procedure as a reference. Steps: 1.
Page 85
Installation Manual of Network Camera Figure 5-4 Mount the Camera 3. View the video image over the network. Loosen the knob on bracket to adjust the camera to the desired surveillance angle. Tighten the knob on bracket to secure the camera. Figure 5-5 Adjust Image...
Installation Manual of Network Camera 5.2 Cube Camera II 5.2.3 Appearance Description Camera description: Figure 5-6 Overview Description Table 5-2 Description Photosensitive resistance Infrared light PIR sensor Microphone Lens Alarm: Indicator is solid red when the camera is armed with PIR and access control and it is solid blue when the camera is unarmed.
Installation Manual of Network Camera Power supply interface 10M / 100M self-adaptive Ethernet interface & PoE Note: To reset the default parameters to the camera, you need to press and hold the RESET button and power on the camera. After the power on of the camera, you must still press and hold the Reset button for about 20 seconds.
Page 88
Installation Manual of Network Camera Note: If you want to install the battery, then you can take this step. Battery Battery Cover Figure 5-9 Insert Battery 3. Stick the drilling template to the ceiling. Notes: For cement ceiling mounting, you need to use expansion screw to fix the camera, and the hole of the expansion pipe should align with the mounting hole of the drilling template.
Page 89
Installation Manual of Network Camera Figure 5-11 Secure the Camera 5. Connect the network cable and power cable; reinstall the right cover and fixator. Note: If you need to pull the cable through the side cable outlet of the camera, pull the cables from the slot without reinstall the fixator.
Page 90
Installation Manual of Network Camera Packing Nut 1 Packing Nut 2 Tilt Figure 5-13 Adjust Image...
Installation Manual of Network Camera Chapter 6 Mini Dome Camera Installation 6.1 Appearance Description Camera description: Figure 6-1 Overview Description Table 6-1 Description Cover Lens P: Power LED indicator, It is solid red when power is applied to the unit. Base plate Set screw hole Set screw of lens...
Installation Manual of Network Camera Figure 6-2 Wiring Diagram 6.2 Installation The ceiling mounting is recommended for this camera. Note: If required, you can use a plier to remove the clip on the side of the back box and then route cables through the opening to secure the cables on the ceiling.
Page 93
Installation Manual of Network Camera 2. Use the screws to fix the base plate on the ceiling. Figure 6-5 Fix the Base Plate 3. View the video image of the camera over the network. 4. Loosen the lens set screws. Figure 6-6 Loosen Set Screws 5.
Page 94
Installation Manual of Network Camera Figure 6-7 Adjust Image Notes: As the lens of camera has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. ...
Page 95
Installation Manual of Network Camera Figure 6-8 Reinstall Figure 6-9 Reinstall...