Sharp AR-5618 Service Manual page 37

：'11/Jul/22
1
Main Sub
Contents
code code
22 14 P-ROM version display
1
1
15 Trouble memory display
16 Duplex print counter display
(Duplex model only)
17 Copy counter display
18 Printer counter display
19 Scanner mode counter display
(Except for AR-5618S/AR-5620S)
21 Scanner counter display
22 SPF jam counter display
(Only when the SPF/RSPF is
1
installed)
50 Developer rotation time display
51 Drum rotation time display
24 01 Jam total counter clear
02 Trouble memory clear
04 SPF counter clear
(Only when the SPF/RSPF is
1
installed)
05 Duplex print counter clear
(Duplex model only)
06 Paper feed counter clear
07 Drum counter clear
08 Copy counter clear
09 Printer counter clear
13 Scanner counter clear
The P-ROM version is displayed on the copy quantity display. The main code and the sub code are
alternatively displayed by 2 digits. The display interval is same as that of the counter display.
LED (AB series)
141%
122%
*1: Only when the NNB is installed.
The trouble codes are acquired from the trouble memory data.
Every time when the magnification ratio display is pressed, the main code of the trouble is displayed
on the 1st ~ 2nd digit.
* The latest 20 troubles are stored in the memory.
The 3rd digit indicates the trouble history code, "A" ~ "J" (meaning of 1 ~ 10).
After "J" is displayed, "A" ~ "J" blinks. (Meaning of 11 ~ 20)
After "J" blinks (meaning of 20), "A" ~ "J" is lighted. (Returns to 1.)
When the [START] key is pressed, the sub code is displayed.
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
* Note that when the history code blinks, the trouble code and the sub code do not blink.
Data is acquired from the duplex print counter variable, and is displayed.
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The copy counter value is displayed. When the [Interrupt] key is pressed, the machine goes into the
sub code input standby mode. When the [CA] key is pressed, the simulation is terminated.
The printer counter value is displayed. When the [Interrupt] key is pressed, the machine goes into the
sub code input standby mode. When the [CA] key is pressed, the simulation is terminated.
The scanner mode counter value is displayed. When the [Interrupt] key is pressed, the machine goes
into the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated.
The scanner counter value is displayed. When the [Interrupt] key is pressed, the machine goes into
the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated.
The SPF jam counter value is displayed. When the [Interrupt] key is pressed, the machine goes into
the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated.
The developer rotation time is displayed. (Three digits are displayed alternatively.)
When [Interrupt] key is pressed, the display goes to the sub code input standby state. When [CA] key
is pressed, the machine goes out of the simulation mode.
The drum rotation time is displayed. (Three digits are displayed alternatively.)
When [Interrupt] key is pressed, the display goes to the sub code input standby state. When [CA] key
is pressed, the machine goes out of the simulation mode.
When the [START] key is pressed, the jam total count value is reset to zero, and zero is displayed.
The trouble memory and the EEPROM trouble history data are cleared and "000" is displayed on the
7-seg display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby
mode. When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the SPF count value is reset to zero and displayed on the 7-seg
display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The duplex print count data is cleared, and zero is displayed on the 7-seg display.
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The paper feed counter data of each paper feed section is cleared, and "000" is displayed on the 7-
seg display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby
mode. When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the drum count and the drum rotation time are reset to zero, and
the drum counter value is displayed on the 7-seg display. When the [Interrupt] key is pressed, the
machine goes into the sub code input standby mode. When the [CA] key is pressed, the simulation is
terminated.
When the [START] key is pressed, the copy count value is reset to zero and displayed on the 7-seg
display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the printer count value is reset to zero and displayed on the 7-seg
display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the scanner count value is reset to zero and displayed on the 7-
seg display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby
mode. When the [CA] key is pressed, the simulation is terminated.
AR-5618S SIMULATIONS 7-7
Details of operation
LED (Inch series)
141% Machine program
122% NNB Program *1
Displayed version