Britax KING II User Instructions

PAGE I
1. PRODUCT OVERVIEW
01
02
03
04
05
06
16
17
Upper belt guide
01 Seat base
06
Seat shell
02 Headrest adjuster (KING II ATS/LS)
07
Release buttons
Headrest adjuster (KING II)
03
08
Lower belt guide
04 Headrest
09
Adjustment lever
Shoulder pads
05
10
4. CARE AND MAINTENANCE
Care for the harness buckle
It is vital for the safety of your child that the harness buckle works correctly. Malfunctions
of the harness buckle are usually caused by accumulations of dirt or foreign bodies.
Malfunctions include the following:
• The buckle latches are ejected only slowly when the red release button is pressed.
• The buckle latches will no longer lock home (i.e. they are ejected again if you try to push
them in).
• The buckle latches engage without an audible "click".
• The buckle latches are difficult to insert (you feel resistance).
• The buckle only opens if extreme force is applied.
Remedy: wash out the harness buckle so that it functions properly once again.
Cleaning the harness buckle
1. Open the harness buckle (press the red button).
12
2. Adjust the seat shell
02 to the upright seating
position.
12
3. Open the Velcro fastener on the crotch pad
25
remove it and retain it.
4. Grasp below the seating area the metal plate
which keeps the buckle 12 at the seat base and
27
turn it into a vertical position.
26
5. Slide the metal plate through the slot
26
6. Soak the harness buckle 12 in warm water with
12
dishwashing liquid for at least an hour.
7. Rinse and dry the harness buckle
12
8. Slide the metal plate 26 edgewise through the slot
in the cover and the seat base.
27
9. Rotate the metal plate 26 90°
DANGER! Pull the harness buckle 12 firmly to ensure
that it is securely fastened.
10. Insert the crotch pad 25 through the slot
secure the Velcro fastener.
Cleaning the occupant sensor
1.
Fold the lower part of the cover updwards.
2.
Remove dirt and dust in the area of the occupant sensor
28 28 with a vacuum cleaner.
DANGER! The occupant sensor 28 must not come in
contact with water.
141106_KING_II_ATS_LS_GB.indd 1
07
08
09
10
11
12
18
13
14
15
Shoulder straps
16
11
Harness buckle
12 17
Adjusting button
18
13
Indicator light (KING II LS)
14
19
Indicator light (KING II ATS)
15
Please ensure that you only use the original BRITAX RÖMER replacement seat
covers, as the seat cover is an integral part of the child safety seat and fulfils im-
portant functions to ensure the smooth operation of the system. Replacement seat
covers are available from your dealer.
• The cover can be removed and washed using the delicates programme of the
washing machine (30°C). Please observe the instructions on the washing label
of the cover.
• The plastic parts can be cleaned with a damp cloth. Do not use any caustic
cleaning agents (such as solvents).
DANGER! The child seat must not be used without the seat cover.
Removing the cover
Loosen the harness straps as far as possible.
1. Open the harness buckle
09 2.
Remove the cover of the headrest
and
25
26
3. 29
Open the poppers on the left and right side of the
rear part of the cover.
29
4. Unhook the elastic seam of the cover under the edge of
.
27
the seat shell.
TIP: Start at the sides of the seat shell.
5.
Pull the cover up and over the bezel of the strap adjuster.
thoroughly.
6. Feed out the harness buckle
from the cover.
7. Pull the cover upwards and remove it over the headrest
09 .
12
27 and The cover can now be washed. Please observe the
instructions on the washing label of the cover:
Re-fitting the cover
Proceed in reverse order to put on the cover.
2. INTRODUCTION
We are delighted that our KING II / ATS / LS
through a new stage in its life.
In order to protect your child correctly, the
ways be used and installed as described in these instructions.
If you have any further questions regarding its use, please feel free to contact us:
BRITAX RÖMER
Kindersicherheit GmbH
T.: +49 (0) 731 9345-199
Blaubeurer Straße 71 F.: +49 (0) 731 9345-210
D-89077 Ulm E.: service.de@britax.com
Germany
www.roemer.eu
BRITAX EXCELSIOR
LIMITED
1 Churchill Way West T.: +44 (0) 1264 333343
Andover F.: +44 (0) 1264 334146
Hampshire SP10 3UW
E.: service.uk@britax.com
United Kingdom www.britax.eu
These instructions use the following symbols stated below:
19
Symbol Keyword
DANGER!
WARNING!
CAUTION!
TIP:
Instructions that follow a set sequence are numbered.
Example:
1. Press the button...
Belt guide colours
For better differentiation, the two vehicle seat
belts are highlighted in different colours. The di-
Adjustment strap
agonal seat belt 21 in dark red and the lap belt
Adjustment handle
in bright red. The colour of the belt guides
22
User guide compartment
on the child safety seat follows the same colour
Harness retainer
scheme.
5. DISASSEMBLY AND DISPOSAL
UNFASTENING YOUR CHILD:
1. To unfasten your child, press the red release button of the 5-Point harness
buckle 12 .
REMOVAL:
1. Unbuckle the vehicle belt buckle
2. Unhook the diagonal belt section
3. To open the shell: push one of the grey release buttons
same time pull the seat shell
4. Remove the diagonal 21 and the lap belt sections
lower belt guides 04 .
5. Hold the seat shell 02 with one hand while pulling the grey adjustment
(press red button).
12
lever 05 forward with the other hand.
09 .
6. To close the shell: tip the seat shell
engagement positions.
WARNING! To avoid injuries take your hand away from the grey
ment lever , as soon as getting over the two engagement positions.
05
7. Push the seat shell 02 with both hands against the seat base
fully engaged.
DISPOSAL:
Please observe the waste disposal regulations in your country..
12 and the end of the strap
Disposal of packaging
Seat cover
Plastic parts
Metal parts
Belt straps
Buckle and tongue
Batteries
3. CERTIFICATION / USAGE
BRITAX RÖMER
can safely accompany your child
Child safety seat
KING II / ATS / LS
must al-
KING II / ATS / LS
The child safety seat has been designed, tested and certified according to the re-
quirements of the European Standard for Child Safety Equipment (ECE R 44/04).
The seal of approval E (in a circle) and the approval number are located on the
orange approval label (sticker on the child safety seat)
DANGER
! This approval will be invalidated if you make any modifications to
the child safety seat. Only the manufacturer is permitted to make
modifications to the child safety seat.
DANGER ! Never secure your child or the child safety seat with a 2-point belt.
If you secure your child in the child seat with only a 2-point belt,
then in the event of an accident this may cause serious injuries to
your child, possibly resulting in death.
Please observe the instructions for using children's restraining systems in the operating
instructions of your vehicle. The seat can only be used in vehicles with 3-point retractor safety-
2)
belts
.
Explanation
Please find the information on the seats approved for child safety seats of the weight classes 9 to
Risk of severe personal injury
18 kg in the operating instructions of your vehicle.
You can use your child safety seat as follows:
Risk of minor personal injury
In the direction of travel
Risk of material damage
Against the direction of travel
Useful notes
with 2-point belt
with 3-point reractor safety belt
on front passenger seat
on outer rear seat
21
on centre rear seat (with 3-point
2)
belt )
1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only
if the vehicle seat is also approved for use by adults. The seat may not be in the area of effect
of an airbag.
2) The seat is only compatible with 3-point retractor type safety-belts, approved to ECE Reg
No. 16 or other equivalent standards.
3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions
22
in vehicle owner's manual.
4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.
9 kg - 18 kg
9 M ~
and loosen the harness straps.
20
21 from the upper belt guide 01 .
03 and at the
as far forward as possible.
02
KING II / ATS / LS
22 from the light red
User instructions
against the seat base over both
02 06
adjust-
06 until it is
Container for cardboard boxes
Residual waste, thermal utilisation
According to the labelling in the
corresponding container
Container for metals
Container for polyester
Residual waste
Container for batteries
www.britax.eu
Testing and certification
In accordance with ECE* R 44/04
*ECE = European Standard for Child Safety Equipment
Group Body weight
I 9 to 18 kg
.
yes
1)
no
9 - 18 kg
no
2)
yes
3)
yes
yes
4)
yes
4 Y
GB
06.11.2014 09:34:59