Related Manuals for Kingtec K35A
Summary of Contents for Kingtec K35A
-
Page 1: Installation Manual
K35A VAN AIR CONDITIONER ASSEMBLY Installation Manual HEYUAN REXKING INDUSTRIAL CO., LTD... - Page 2 Forward The correct installation is most important to ensure optimum utilities, to improve the reliability and economic and to reduce the downtime. The principle of the manual is to provide technical instruction on top – installed air conditioner assembly for the technicians before and after sales services. Read and follow the instruction mentioned in the user manual carefully.
-
Page 3: Table Of Contents
Content 1. Safety Precaution ············································································ 3 2. Technical Preparation Before Installation ······································· 4 3. Air Conditioner Guarantee ······························································ 5 4. Assembly Selection ········································································ 5 5. Installation Assembly ······································································ 6 6. Font panel commands ···································································· 12 7. Maintenance ··················································································· 12 8. Troubleshooting ·············································································· 13 Table1 ··································································································... -
Page 4: Safety Precaution
1.Safety Precaution 1). Wear working suit, working shoes when making operation. Do not wear slippers, short pants or waistcoat when installing the equipment. 2). Wear goggle or safety glasses preventing the dust or chips falling into the eyes when looking up. 3). -
Page 5: Technical Preparation Before Installation
5). Check the isolation of the cable connection when connecting to 220V power supply. 6). The refrigerant will produce poisonous gases when there is bright fire. The personnel will suffocate or die when taking breathe the poisonous gases. The spray of the refrigerant will hurt the body. The protection is the most important before installation. - Page 6 12 months guarantee from the date of sales. The guarantee will be ensured with our guideline and instruction. KINGTEC will not take the responsibility on misuse incorrect filter, normal delivery, adjusting and transportation damages. The Certificate Guarantee is the only one.
-
Page 7: Assembly Selection
See the Appendix 1 attached. 4. Assembly Selection 1). Selection: K35A is suitable installed on trailing car or van. The written approval must be provided by technical department if mounting the assembly on the MUT or industrial vehicles to ensure the guarantee. -
Page 8: Installation Assembly
6 meters. 5. Installation Assembly 1). Roof strength There must be enough strength since the K35A air conditioner assembly is about 50kg. The top strength of normal car is not enough except the special vehicles with air conditioning required. Contact the car manufacturer on the top strength or provide enough supporting with H-type bracket. - Page 9 Figure 1 The figure1 describes the installation position of the air conditioner on van roof and ceiling. 1. Install the unit on the front part of the top van，ensure the unit exhaust in outdoor un-effect. 2. Do not install the unit at the place where affecting the air return or exhaust. Since it will affect the uniform of the temperature of inside van.
- Page 10 AI R FLO W AI R FLO W D i r ect i on of car dr i vi ng Figure 2 Figure 3...
- Page 11 3). Installation Angles of the unit Ensure the following items if there is angle on top van: (i) The unit is backboards incline instead of forwards incline. (ii) The inclined angle will no be larger than 7º. If the unit is forwards inclining, the discharge of the condensation will be affected.
- Page 12 6). Outdoor unit installation 1). Clean the holes and surrounding with the distance at least 75mm with grease after drilling the installed hole. 2). Stick the EVR stripe attached along the sides and seal the surface with glue; 3). Make the four fixing bolt tight, ensuring the gap 22mm for discharging between lower surface of the unit and top surface of the van.
- Page 13 7). Connection cable Figure 5 is the connection of power supply. It is connected with insert and interior channel. Connect the adaptors properly as shown in Figure 5. Figure 5 8）. Fix interior air channel With four M4 × 35 of the self-tapping screw fixation in the mounting bra ckets,...
-
Page 14: Font Panel Commands
6.Font panel commands By pushing and releasing this button ,The unit power “on” or “off” By pushing and releasing this button,Select the Function mode By pushing and releasing this button,Set indoor temp. By pushing and releasing this button, Set the fan speed NOTE：... -
Page 15: Troubleshooting
appearance indicates the air return filter needed to be washed. Open the filter plate with screwdriver and take out the screen. Clean it with suds and dry. Put the filter into the right place. 8. Troubleshooting 1). Compressor not refrigerating Troubles Possible reasons Solution... -
Page 16: Table1
Table 1 Customer Info ……………………………………………………………………………… Name ……………………………………………………………………………… Address ……………………… …………………… …………………………… P.C. Phone …………………………………………………………………… Purchase Date ……………………………………………………………………………… Model ………… …………… …………… …… ………………… ……………… S/N: ……………………………………………………………………………… Install: …………………………………………………………………… Purchase Place ……………………………………………………………………………… Address ……………………P.C. ……………………… ……………………… Phone... -
Page 17: Table
Current Refrigerant R407c/700g Evaporation 650m Dimension (L*W*H) 1050*595*245mm Assembly Weight 50kg Refrigerating conditions: Indoors dry ball 27.C, wet ball 19.5.C; Outdoors dry ball 35.C, wet ball 27.C. KINGTEC keeps the right on products changing without notification in advance. -
Page 18: Appendix1
Appendix 1 K35A ELECTRI C CLRCUI T DI AGRAM FUSE ～Power NOTE: Fuse Capaci t ance Ai r r et ur n Tem Tr ansf or m er Power r el ay i n- door heat exchange Condenser f an...