DIGITAL CAMERA FinePix S3000 SERVICE MANUAL WARNING THE COMPONENTS IDENTIFIED BY THE MARK “ ” ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY. PLEASE REPLACE ONLY BY THE COMPONENTS SPECIFIED ON THE SCHE- MATIC DIAGRAM AND IN THE PARTS LIST.
Page 2
FinePix S3000 Service Manual SAFETY CHECK-OUT 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. RISK OF FIRE- REPLACE FUSE 2.5A 125V AS MARKED 2.5A 125V WARNING! HIGH VOLTAGE...
TABLE OF CONTENTS 1.General .......... 5 4.Adjustment ........37 1-1. Product specification .......... 5 4-1.Important point Adjustment when Replacing Major Parts ..37 1-2. Explanation of Terms .......... 7 4-2.The order of adjustment when Major Parts are replaced ..37 1-3.Names of External Components ......
FinePix S3000 Service Manual 1.General 1-1. Product specification System Model Digital Camera FinePix S3000 Effective pixels 3.2 million pixels 1/2.7-inch square pixel CCD with RGB Filter Number of total pixels: 3.34 million pixels Storage media xD-Picture Card (16/32/64/128/256/512 MB) File format Still image: JPEG (Exif Ver.2.2), DPOF-compatible...
Page 5
DPC-16 (16 MB)/DPC-32 (32 MB)/DPC-64 (64 MB)/DPC-128 (128 MB)/ DPC-256 (256 MB)/DPC-512 (512 MB) AC Power Adapter AC-5VH/AC-5VHS Fujifilm Rechargeable Battery 2HR-3UF Fujifilm Battery charger with Battery BK-NH/BK-NH2 (With Euro type or UK type plug) SC-FX304 Image Memory Card Reader DPC-R1 •...
FinePix S3000 Service Manual 1-2. Explanation of Terms DPOF: Digital Print Order Format DPOF is a format used for recording information on a storage media (image memory card, etc.) that allows you to specify which of the frames shot using a digital camera are printed and how many prints are made of each image.
2-2.How to Disassemble the CABI R ASSY. Remove in the order indicated by circled numbers. <Step1> (1) Change to the Manual camera mode. (2) Remove three screws. (3) Remove two special shape screws.(3ULR 1.5X5.0) *Because the screws are special shape,use the exclusive use jig driver(ZJ00583-100).
FinePix S3000 Service Manual 2-3.Removing LCD ASSY / LCD FRAME. Remove in the order indicated by circled numbers. <Step1> (1) Remove two screws. (2) Remove the hook of LCD FRAME (two places), and raise LCD ASSY in the direction of the arrow.
2-5.Removing MAIN PWB ASSY. Remove in the order indicated by circled numbers. <Step1> (1) Remove CN101 CN203, CN301, CN350and CN502. (2) Remove MAIN PWB ASSY in the direction of the arrow while removing the connector in A part. 2-6.Removing BATTERY HOLDER ASSY. Remove in the order indicated by circled numbers.
FinePix S3000 Service Manual 2-7.Removing DCST PWB ASSY. Remove in the order indicated by circled numbers. <Step1> (1) Remove two screws. (2) Remove CN701, CN702. (3) Raise DCST PWB ASSY in the direction of the arrow. <Step2> (4) Remove FPC of LENS CONST in the direction of the arrow.
2-9.Removing STROBE CONST/ST TOP. Remove in the order indicated by circled numbers. <Step1> (1) Remove one screws. (2) Remove STRAP BASE(R) in the direction of the arrow. <Step2> (4) Remove one screws. (5) Remove the hook of ST BUTTON, and pull out ST BUTTON in the direction of the arrow.
FinePix S3000 Service Manual 2-10.Removing MSW PWB ASSY and RSW PWB ASSY. hook Remove in the order indicated by circled numbers. <Step1> (1) Remove one screw. (2) Remove the hook of BATTERY HOLDER, and remove RSW PWB ASSY and MSW PWB ASSY.
2-12.Removing CCD PWB CONST Remove in the order indicated by circled numbers. (1) Remove tow screw. (2) Remove the hook of CCD PWB CONST. CCD PWB LPF RUBBER OPTICAL LPF LPF MASK LENS UNIT [Attention when CCD PWB CONST is exchanged. ] Solder the WIRE HARNESS with new parts when you ex change CCD PWB CONST.
FinePix S3000 Service Manual 2-13.Location of Sheet parts. 2-13-1.FFC (CCD-MAIN) MAIN PWB FERRITE BEADS fixed to FFC. Position at 15mm from MAINPWB side. EMI SHEET (FZ05597-100) [Note] Do not exceed Fold-Line of FFC. 15mm Fold line FERRITE BEADS (FLBZ120-100) CAPTON TAPE EMI SHEET fixed to FFC.
3.Schematics 3. Circuit Diagrams 3-1.Cautions Precautions in parts replacement Do not reuse detached electronic components. Use only new components. The negative side of tantalum capacitors is weak against heat. Handle with care. With the exception of Chemical capacitor and tantalum capacitors, the voltage of capacitors of a 50V or lower withstand voltage is not labeled.
FinePix S3000 Service Manual 3-3.Explanation of Functions of Important Blocks 3-3-1.Technical Overview The FinePix S3000 incorporates a 1/2.7 -inch square pixel, primary color interline CCD of 3.34 million pixels(total). An [xD picture card] is adopted as the recording media. Change point from S304/3800.
(Note1) It is a type that the harness of POWER CABLE JIG so far becomes long. The adjustment is possible even by past POWER CABLE JIG. (Note2) Please downloaded from Web server (http://fujifilm-di.intranets.com/). (Note3) Select one the power cable suitable each country.
4.Adjustments 4-4.Jig Connections Note1: Connect all jigs and start PC. Note2: Do not connect the video cable with "VIDEO OUT" Jack of the camera, except when you adjust the video. Note3: Input voltage is a thing measured in a part near "DC_IN" Jack. Note4: Limit the current value to 2.5A or less.
Page 38
4.Adjustments FinePix S3000 Service Manual (2) Environmental Setup for AF Adjustments (Fig. B) [1] Set the Siemens Star Chart 890 5 mm from the convex side of the conversion lens. [2] Irradiate the Siemens Star Chart with a light source so that the surface brightness of the Siemens Star Chart is 9.0 ~ 11.5Ev.
<Step 1> The setup software is downloaded from WEB, and software is installed in the PC. We have uploaded the ”DSC Jig Driver(ZJ00476-101)” on our website: (http://fujifilm-di.intranets.com/). <Step2> Double-click on [setup.exe](Fig.F) in the file, and follow the instructions on the screen to install the jig driver.
4.Adjustments FinePix S3000 Service Manual 4.8 Initial Settings of the Adjustment Software * The initial settings are already written in the "FFWJ.ini" file, therefore perform the following procedure to the letter. Note that, if you change file names, the software will not start up.
Page 41
4.Adjustments <Step 4> Select the "Etc" tab (Fig. 3-(1)) in the "Customize" dialog box that appears. Set the "Other" items (Fig. 3-(1)) as fol- lows. Item Details Auto Measurement Change mode(-U) Do not check Use Japanese Fonts Do not check Don’t show OK NG Check or Do not check <Fig.
Page 42
Clear OKNG Do not use. [Caution 2] Set Mode Sets the mode Auto Run user program The FinePix S3000 is able to batch-read data, Adjustment Auto Adjust. however it is unable to batch-write data (file Help Help Basic software help read, ROM write).
4.Adjustments 4-9. Starting the Adjustment Software <Step 1> Double-click on the "FFW.EXE" in the folder copied to the C drive to display the adjustment software start-up scren.(Fig.1) >> The [FFW.EXE Startup screen (Fig.1)] is appears. <Fig. 1> <Step 2> Press the "Enter" key of the PC or click on the start button (Fig.1-(1)) in the toolbar.
Page 44
4.Adjustments FinePix S3000 Service Manual <Step 4> After reading the notes, press the "Enter" key of the PC. >> The [Jig Mode Setting Procedures screen (Fig.4)] is appear. How to Set Up the Jig Mode 1. Set the mode switch to the camera mode.
No. shown at right.(Fig. CCD1) <Fig. CCD1> <Step 1> Note the CCD serial No. on the CCD CONST and MAIN (http://fujifilm-di.intranets.com/). PWB ASSY when replacing the MAIN PWB ASSY. The numbers shown at right are as follows. First line: 0400002 (seven digits)
Page 46
4.Adjustments FinePix S3000 Service Manual < Adjustment > <Step 1> Select [F4] CCD Defect Data Input adjustment on the [Adjustment Items Select] screen(Fig.5). <Step 2> —> Set the xD picture card (can be recorded )in the camera. —> Set LENS HOOD and LENS CAP in the camera.
Page 47
4.Adjustments <Step 4> —>Wait until the CCD temperature is steady (Fig. CCD5). < Fig. CCD5> <Step 5> —> Write the adjustment data to the flash ROM when adjustment has been completed correctly. —> The [CCD Defect Data Input adjustment Complete] screen appears(Fig. CCD6). <...
4.Adjustments FinePix S3000 Service Manual 4-11. [F5] CAM Adjustment (shutter adjustment, adjustment for reduced aperture sensitivity, ISO sensitivity adjustment, white balance adjustment, AE adjustment, offset level adjustment) <Step 1> Select [F5] CAM Adjustment on the [Adjustment Items Select] screen (Fig.5).
Page 49
4.Adjustments <Step 4> <Fig. CAM3> —> The [CAM Adjustment (without filter)] screen appears(Fig. CAM4). <Step 5> <Fig. CAM4> —> Write the adjustment data to the flash ROM when adjustment has been completed correctly. —> The [CAM Adjustment Complete] screen appears(Fig. CAM5). <Note>...
4.Adjustments FinePix S3000 Service Manual <Step 6> <Fig. CAM5> 4-12. [F6] AF Adjustment <Step 1> Select [F6] AF Adjustment on the [Adjustment Items Select] screen (Fig.5). —> The [AF Adjustment Preparation] screen appears. <Step 2> Run the adjustment in accordance with the instructions on the screen.
Page 51
4.Adjustments <Step 3> <Fig. AF2> —> Write the adjustment data to the flash ROM when adjustment has been completed correctly. —> The [AF Adjustment Complete] screen appears. <Step 4> <Fig. AF3>...
4.Adjustments FinePix S3000 Service Manual 4-13. [F1] Battery Voltage Adjustment <Step 1> Select [F1] Battery Voltage Adjustment on the [Adjustment Items Select] screen (Fig.5). —> The [Battery Voltage Adjustment Preparation] screen appears. <Step 2> Run the adjustment in accordance with the instructions on the screen.
Page 53
4.Adjustments <Step 4> <Fig. BATT3> —> The [5.00V Input] screen appears. <Step 5> <Fig. BATT4> —> Write the adjustment data to the flash ROM when adjustment has been completed correctly. —> The [Battery Voltage Adjustment Complete] screen appears.
4.Adjustments 4-14. [F3] LCD Adjustment <Step 1> Select [F3] LCD Adjustment on the [Adjustment Items Select] screen (Fig.5). —> The [LCD Adjustment Preparation] screen appears. <Step 2> Run the adjustment in accordance with the instructions on the screen. <Fig. LCD1> <Note>...
4.Adjustments FinePix S3000 Service Manual 4-15. [F7] Flash Adjustment <Step 1> Select [F7] Flash Adjustment on the [Adjustment Items Select] screen (Fig.5). —> The [Flash Adjustment Preparation] screen appears. <Step 2> Run the adjustment in accordance with the instructions on the screen.
4.Adjustments <Step 4> <Fig. FLASH3> 4-16.[F11] : Video Adjustment < Setup for Video Adjustment > Set up the PCI-2746C board in the computer as explained in the instructions for the video adjustment box. If the waveform of the brightness signal (Y) or color signal (C) does not appear in the “WAVE No. 0” window during adjustments, check the connections of the video adjustment box.
Page 58
4.Adjustments FinePix S3000 Service Manual < Adjustment > <Step 1> Select [F11] Video Adjustment on the [Adjustment Items Select] screen (Fig.5). —> The [Video Adjustment Preparation] screen appears. <Step 2> Run the adjustment in accordance with the instructions on the screen.
4.Adjustments 4-17. [F12] : End Setting (Destination setting, USB ID write, Product mode setting) The setting must always be run when the adjustment software is terminated. Failure to run Terminal Setting will prevent identification as Mass Storage when the camera is connected to the PC. USB ID write requires that the USB device (in this case FinePix A205) be unique throughout the world.
Page 60
4.Adjustments FinePix S3000 Service Manual <Step 2> Select [F12] End Setting on the [Adjustment Items Select] screen (Fig.5). —> The [End Setting Description] screen appears. <Step 3> Run the adjustment in accordance with the instructions on the screen. <Fig. END1>...
Page 61
4.Adjustments <Step 5> <Fig. END3> —> The [USB ID Writing] screen appears. <Step 6> <Fig. END4> <Note> This example assumes that <H>USA has been selected. The following screen therefore appears. —> The [USA_ID USA] screen appears.
4.Adjustments 4-18. [F8] Firmware Download [ Download and Extract ] 1) Download the firmware(archived file) from Web server (http://fujifilm-di.intranets.com/ ). 2) Extract the downloaded archived firmware. 3) The folder named ZJ00841-100 can be made by simply defrosting(Fig .FIRM1). 4) The imfidx10 folder is include in the folder ( ZJ00841-100 ).
Page 64
4.Adjustments FinePix S3000 Service Manual <Step 1> Select [F8] Firmware Download on the [Adjustment Items Select] screen (Fig.5). —> The [ Firmware Download ] screen appears. <Fig. FIRM3> <Step 2> Prepare the firmware download according to the instruction of the screen.
Page 65
4.Adjustments <Step 3> Turn off the power supply of the camera according to the instruction of the screen. *The camera is started with the new firmware when power is switched OFF/ON. <Fig. FIRM5> —> Press the [Enter] key to return to the "Initial Screen(Fig.2)". <Step 4>...
5.Inspection 5.Inspection 5-1.Required Measuring Equipment Measuring equipment Remarks Power supply AC adapter (AC-5VH / AC-5VHS), stabilized power supply Digital voltmeter For general use Ammeter For general use (able to measure 1mA or less) power cable jig For general use xD-Picture card For general use TV-Monitor For general use (Resolution 600 or more)
5.Inspection FinePix S3000 Service Manual Method of adjustment Measuning Preparations for adjustment Measurement point Check item Sequence Mode (measurement point, subject, other) (VRs, waveforms, required, values) equipment and jigs (VRs, position) Battery down Playback 1)Connect the power cable jig with Power cable jig the camera.
FinePix S3000 Service Manual 6-5.Electrical parts Due to standardization,replacement in the parts list may be The components indicated by mark are critical for safty. different from the parts list specified in the circuit or the com- When indicated parts by reference number,please include ponents used on the set.
7.Appndix 7.Appendix 7-1. Version display function This function is not provided in FinePix S3000. 7-2.List of Related Technical Updates Issued To ensure that after-sales srevice is performed accuratety, keep a record here of the technical updates issued that cover this device.
Page 82
FUJI PHOTO FILM CO., LTD. 26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.