Page 1
I N S T R U C T I O N M A N U A L HYDRAULIC BENCH-MOUNTED GRINDER P P / / N N 1 1 0 0 9 9 1 1 7 7 9 9 F O R A S S E M B LY S E T - U P A N D O P E R A T I O N A L U S E This manual contains...
Page 2
O W N E R ’ S I N F O R M A T I O N A N D R E S P O N S I B I L I T Y SAFETY SYMBOLS AND WARNINGS The following symbols are used to draw special attention to operator and/or bystanders to help prevent possible injury.
T A B L E O F C O N T E N T S ▲Introduction 2- 5 Safety Rules and Precautions Parts Included for Assembly Grounding Instructions ▲ Assembly Instructions Mounting-Base Unit to Bench or Wall Selecting and Mounting the Grinding Wheel Dressing the Grinding Wheel ▲Operating Instructions 8-12...
I N T R O D U C T I O N T T O O A A V V O O I I D D P P E E R R S S O O N N A A L L I I N N J J U U R R Y Y T T O O Y Y O O U U A A N N D D T T O O B B Y Y S S T T A A N N D D E E R R S S , , R R E E A A D D A A N N D D F F O O L L L L O O W W T T H H E E S S E E S S A A F F E E T T Y Y R R U U L L E E S S .
Page 5
I N T R O D U C T I O N 1 1 2 2 . . K K e e e e p p w w o o r r k k a a r r e e a a c c l l e e a a n n . . Cluttered areas and 2 2 2 2 .
I N T R O D U C T I O N PARTS INCLUDED FOR ASSEMBLY Refer to this page when following assembly instructions which call out a specific name and part number. T T h h e e s s e e p p a a r r t t s s a a r r e e i i n n c c l l u u d d e e d d t t o o c c o o m m p p l l e e t t e e t t h h e e a a s s s s e e m m b b l l y y o o f f t t h h e e O O R R E E G G O O N N ®...
I N T R O D U C T I O N The grinder must be used only in a place that is protected from dust and dampness, that is well-lighted, out of the reach of children, and away from gases or other flammable or explosive liquids.The grinder must be situated near a normal electrical outlet equipped with earth (grounded).
A S S E M B L Y I N S T R U C T I O N S Figure 3 Assembly/Setup A A . . M M o o u u n n t t G G r r i i n n d d e e r r t t o o a a B B e e n n c c h h o o r r W W a a l l l l : : 1 1 .
A S S E M B L Y I N S T R U C T I O N S Figure 5 Figure 7 ON/OFF C C . . D D r r e e s s s s i i n n g g T T h h e e G G r r i i n n d d i i n n g g W W h h e e e e l l : : minute before wheel is dressed.
O P E R A T I N G I N S T R U C T I O N S Table 1 Volts Cord length Amps Gauge needed Amps Gauge needed 115/120V 25 ft 0 - 6 10 - 12 6 - 10 12 - 16 115/120V...
O P E R A T I N G I N S T R U C T I O N S Figure 9 Grinding A Chain (cont.) Chain There is risk of serious Direction personal injury for chain- saw operators or bystanders from improperly sharpened saw chain.
O P E R A T I N G I N S T R U C T I O N S Figure 11 Figure 13 Step 3 Step 4 proper depth adjustment during the grind 4 4 . . S S e e t t t t i i n n g g v v i i s s e e - - t t i i l l t t a a n n g g l l e e . . For saw chains operation.
O P E R A T I N G I N S T R U C T I O N S 9 9 . . Lower the grind head/wheel into the grind Figure 16 position and g g r r i i n n d d a a l l l l r r i i g g h h t t - - h h a a n n d d c c u u t t t t e e r r s s , , r r o o t t a a t t e e v v i i s s e e a a n n d d g g r r i i n n d d a a l l l l l l e e f f t t - - h h a a n n d d c c u u t t t t e e r r s s (see Figure 15).
O P E R A T I N G I N S T R U C T I O N S Figure 18 grind for the rest of the depth gauges (see Figure 20). 8 8 . . Turn the power switch to the on position and grind all depth gauges.
Page 16
E X P L O D E D V I E W S E X P L O D E D V I E W S Hydraulic Bench-Mounted Grinder Hydraulic Bench-Mounted Grinder Item No. Part No. Item No. Part No. Description Description Item No.