General Information - Lennox Merit Series Care And Operation Instructions Manual

LENNOX HEARTH PRODUCTS • MERIT

GENERAL INFORMATION

The fireplace models covered in this manual
are direct-vent sealed combustion gas fire-
places designed for residential application.
These direct-vent appliances operate with the
combustion chamber completely isolated from
the indoor environment.
All air for combustion is brought in from the
outside and exhaust gases are vented through
the same direct-vent, co-axial (intake/exhaust)
vent system.
The Millivolt appliances have a millivolt gas
control valve with piezo ignition system. If any
optional accessories which require electrical
power are being installed, the electrical power
must be provided at the time of appliance
installation.
The Electronic appliances have a battery
backed-up electronic intermittent pilot sys-
tem. The battery back-up will allow you to
continue operation of the appliance during a
power outage.
These appliances comply with National Safety
Standards and are tested and listed by ETL/
Intertek (Report No. 100353019PRT-002) to
ANSI ZZ21.50 (in Canada, CSA-2.22), and
CAN/CGA-2.17-M91 in both USA and Canada,
as vented gas fireplaces.
The Installation must conform to local codes
or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA
54-latest edition, or the Natural Gas and Pro-
pane Installation Code, CAN/CSA B149.1-latest
edition. The appliance, when installed, must be
electrically grounded in accordance with local
codes or, in the absence of local codes, the
latest edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical Code,
CSA C22.1 - latest editions.
bTU Input
Millivolt and electronic models come standard
with a manually-modulated gas valve; flame
appearance and heat output can be controlled
at the gas valve. The BTU inputs for these ap-
pliances are shown in Table 1.
Input (bTU/HR) Manually Modulated
Gas Valves (all models)
Input Rate (bTU / HR)
Model
Nat. Gas
14,500 high
MLDVTCD-35
11,500 low
Table 1
SERIES DIRECT-VENT CONTEMPORARY DESIGN GAS FIREPLACES • MODEL MLDVTCD-35 • CARE AND OPERATION
®
Gas Pressure Requirements
(All Models)
Gas pressure requirements are listed in
Tables 2 and 3.
Test gauge connections are provided on the
front of the millivolt gas control valve, identi-
fied IN for the inlet and OUT for the manifold
side (see Figure 3 on Page 9). A 1/8" NPT
Test gauge connection is provided at the inlet
and outlet (manifold) ports on the electronic
gas control valve (see Figure 4 on Page 9).
Inlet Gas Supply Pressure (all models)
Fuel #
Natural Gas
Propane
Table 2
Manifold Gas Supply Pressure (all models)
Fuel #
Natural
Gas
Propane
Table 3
These appliances must be isolated from
the gas supply piping system (by closing
their individual manual shut-off valve)
during any pressure testing of the gas
supply piping system at test pressures
equal to or less than 1/2 psig (3.5 kPa).
These appliances and their individual
shut-off valves must be disconnected
from the gas supply piping system dur-
ing any pressure testing of that system
at pressures greater than 1/2 psig (3.5
kPa).
burn-in Period
During the first few fires in this appliance,
there will be some odor due to the curing of
the paint and burning off of lubricants used in
the manufacturing process. Depending on your
use, the burn-in period may take a few hours
or a few days.
Prop. Gas
KEEP YOUR HOUSE WELL VENTILATED
13,500 high
DURING THE bURN-IN PROCESS. THE ODOR
10,500 low
AND HAZE EMITTED DURING THE bURN-IN
PROCESS CAN bE QUITE NOTICEAbLE AND
MAY SET OFF A SMOKE DETECTOR.
If an optional blower is installed, do NOT turn
it on during the burn-in period.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Minimum Maximum
4.5" WC 10.5" WC
(1.12 kPa) (2.61 kPa)
11.0" WC 13.0" WC
(2.74 kPa) (3.23 kPa)
Low High
(Lo) 2.2" WC (Hi) 3.5" WC
(0.55 kPa) (0.87 kPa)
(Lo) 6.3" WC (Hi) 10.0" WC
(1.57 kPa) (2.49 kPa)
Orifice Sizes
(Sea Level to High Altitude – All Models)
These appliances are tested and approved for
installation at elevations of 0-4500 feet (0-1372
meters) above sea level using the standard burner
orifice sizes (marked with an "*" in Table 4). For
elevations above 4500 feet, contact your gas
supplier or qualified service technician.
Deration
At higher elevations, the amount of BTU fuel
value delivered must be reduced by either:
• Using gas that has been derated by the gas
company.
• Changing the burner orifice to a smaller size
as regulated by the local authorities having
jurisdiction and by the (USA) National Fuel
Gas Code NFPA 54/ANSI Z223.1 - latest
edition or, in Canada, the CAN/CSA-B149.1
codes - latest edition.
Install the appliance according to the regulations
of the local authorities having jurisdiction and,
in the USA, the National Fuel Gas Code NFPA
54 / ANSI Z223.1 - latest edition or, in Canada,
the CAN/CSA-B149.1 - latest edition.
NOTE: Flame appearance will diminish 4% per
thousand feet.
burner Orifice Sizes
Elevation 0-4500 feet ( 0-1372 meters)
Model Nat.Gas
Series drill size (inches)
#49 (0.073") *
MLDVTCD-35
21L82 •
* Standard size installed at factory.
** Standard size in LP conversion kit.
Table 4
• Part /Cat. Number.
IMPORTANT NOTE!
A white film may develop on the glass
enclosure panel during the first few
fires as part of the burn-in process.
The first few times you use the
fireplace, clean the glass after
each use (AFTER THE GLASS HAS
COMPLETELY COOLED); otherwise,
the white film will bake onto the
glass and become difficult to
remove.
See "Cleaning Glass" on Page 10.
Propane
drill size (inches)
0.045" **
75L10 •
7