Table of Contents
Advertisement
Quick Links
1. ROUGHING IN: K 700 VINTAGE BATH
A. ORDERING INFORMATION
Accessories/hardware:
Drain for drop-in
Drain for free-standing
Adjustable legs
Roughing-In Notes
Fixture dimensions are nominal and conform to toler-
ances in ANSI Standard A112.19.1.
No change in measurements if connected with drain
illustrated.
69" (175.3cm)
CUTOUT DETAIL
19" R.
40" (101.6cm)
(48.3cm)
42" (106.7cm)
3-3/4" (9.5cm)
3" (7.6cm)
AB
110050-2-
R
K-7158
recommended
K-7159
recommended
K-1172
optional
2-3/8"
(6cm)
4" (10.2cm)
21-3/16"
(53.8cm)
1-1/2" I.P.S. THR'D.
1-1/2" O.D.
CAST IRON BATH
B. PRODUCT INFORMATION
Fixture*:
basin area
Bathing
44" (111.8cm)
well
x 24" (61cm)
water depth
Overflow
15" (38.1cm)
* Approximate measurements for comparison only.
Included Components:
Cutout template
C. INSTALLATION NOTES
Read the entire installation instruction before beginning
the installation.
NOTICE: The floor must support 2,000 lbs (907kg). This is
the combined weight of the bath, water, and two bathers.
Pre-plan access for moving the bath into the construction
area; the bath is heavy and will not fit easily through door-
ways.
13-1/4"
(33.7cm)
36" (91.4cm)
72" (182.9cm)
VINTAGE
K-700
top area
weight
60" (152.4cm)
485 lbs.
x 32" (81.3cm)
(220kg)
capacity
82 gals.
(310L)
106594-7
18-1/4"
(46.4cm)
1-1/8"
(2.9cm)
10-3/4"
(27.3cm)
4"
(10.2cm)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kohler VINTAGE K-1172
Summary of Contents for Kohler VINTAGE K-1172
- Page 1 1. ROUGHING IN: K 700 VINTAGE BATH A. ORDERING INFORMATION Accessories/hardware: Drain for drop-in K-7158 Drain for free-standing K-7159 Adjustable legs K-1172 Roughing-In Notes Fixture dimensions are nominal and conform to toler- ances in ANSI Standard A112.19.1. No change in measurements if connected with drain illustrated.
-
Page 2: Ordering Information
77” (195.6cm) x 47” (119.4cm) WOOD TOWEL BAR 3” (7.6cm) É É É 32” (81.3cm) WOOD BASE/CERAMIC FLOOR RAIL Kohler Co., Kohler WI U.S.A. B. PRODUCT INFORMATION Fixture*: basin area Bathing 44” (111.8cm) required* well x 24” (61cm) -
Page 3: Product Requirements
Page For replacement installations: Remove the old bath. Remove the old wall material, and remove any old floor covering from the area. Remove any old plumbing that does not conform to roughing in requirements. Kohler Co., Kohler WI U.S.A. -
Page 4: Site Preparation
Modifications may be needed for other types of construction. NOTICE: Do not install the wood rim to units used in sunken installations. Corner Installation: The suggested stud construction is illustrated. Kohler Co., Kohler WI U.S.A. Old Bath Floor Protection Boards 69” (175.3cm) 19” R. -
Page 5: Plumbing Preparation
Insert the dowels in the ends of the floor rail. Apply silicone sealant to the end rails, and press them completely onto the dowels. Remove any excess sealant. 110050-2- suggested stud Floor Rail Apply Silicone Sealant Dowel Screws Floor Bracket Kohler Co., Kohler WI U.S.A. - Page 6 Do not use this wood rim in sunken installations. CAUTION: Option sealant: NOTE: using silicone sealant: 8. INSTALL THE TOWEL BAR Kohler Co., Kohler WI U.S.A. Rim Bracket Locations using silicone Option for Support Bracket Setscrews...
-
Page 7: Install Plumbing
Install the faucet valving and spout tee. Open the hot and cold water valves, and check the supply connections for leaks. Run water into the bath, and check the drain connections for leaks. 110050-2- Metal Shims Metal Shim damage. Connect Here Kohler Co., Kohler WI U.S.A. -
Page 8: Install The Faucet Trim
Questions? Problems? First review the installation instructions to ensure correct installation. For additional assistance, call our Customer Service Department for direct help. You may also contact us at our web site listed below. Kohler Co., Kohler, WI U.S.A. Kohler Co., Kohler WI U.S.A. Whirlpool Do not use metal scrapers, wire brushes, or other metal tools.
Need help?
Do you have a question about the VINTAGE K-1172 and is the answer not in the manual?
Questions and answers