General - Sony XDR-S3HD Service Manual

A
POWER SLEEP BAND RADIO / LINE IN
VOLUME
AM FM SIRIUS XM SLEEP ALARM
B
Size AAA (R03)
× 2
Preparing the
remote commander
Installing the batteries into the remote
commander (See Fig. B)
Insert two size AAA (R03) batteries (not supplied).
SECTION 1

GENERAL

PRESET TONE DISPLAY MENU ENTER
TUNE/SELECT
ANTENNA
AM RESET
FM
LINE IN
AC power cord
POWER
ALARM SLEEP
1 2 3
4 5 6
7 8 9
0
ENTER
VOL
PRESET
TUNE/
SELECT
TONE
HD SCAN BAND
RADIO/
MENU SCAN LINE IN
BRIGHT DISPLAY
The number 5 and the VOL +
buttons have a tactile dot.
When to replace the batteries
With normal use, the batteries should last for about six
months. When the remote commander no longer
operates the unit, replace all the batteries with new ones.
Notes
• Do not charge dry batteries.
• When you are not going to use the remote commander
for a long time, remove the batteries to avoid any
damage caused by leakage and corrosion.
Setting the clock
1
Plug in the unit.
The display will flash "AM 12:00."
2
Press MENU to show the menu display.
3
Turn TUNE/SELECT clockwise to select
"TIME SET," then press ENTER.
The hour will start to flash in the display.
4
Turn TUNE/SELECT clockwise or
counterclockwise until current hour appears in
the display, then press ENTER.
The hour is set and the minutes start to flash.
5
Repeat step 4 to set the minute.
Note
If you do not set the menu within 65 seconds, the setting
mode is canceled.
To change the display to the
daylight saving time
(summer time) indication
1
Press MENU to show the menu display.
2
Turn TUNE/SELECT clockwise or
counterclockwise to select "DST," then press
ENTER.
3
Turn TUNE/SELECT counterclockwise to
select "ON," then press ENTER.
" " appears and the time indication changes to
summer time.
To deactivate the DST function, select "OFF" in step 3.
Playing the radio
—Manual tuning
1
Press POWER to turn on the radio.
If "LINE IN" is displayed, press RADIO/LINE IN
so that the band (AM or FM) appears.
2
Press BAND to select the band AM or FM.
3
Turn TUNE/SELECT clockwise or
counterclockwise to tune in to a desired
frequency.
A beep sounds when the minimum frequency of
each band is received during tuning.
4
Adjust the volume using VOLUME.
Tip
To attenuate the volume, turn VOLUME
counterclockwise quickly.
Note
The frequency cannot be input with the number buttons
of the remote commander.
—Preset tuning
You can preset 20 stations each for AM and FM.
Presetting a station
1
Follow steps 1 to 3 in "Manual tuning" to
tune the frequency you wish to preset.
2
Press and hold PRESET for a few seconds.
You will hear a beep.
3
Turn TUNE/SELECT clockwise or
counterclockwise to select the preset number,
then press ENTER.
The frequency is stored in the selected preset
number and you will hear a beep.
To preset another station, repeat these steps.
Note
If you try to store another station in the same preset
number, the previously stored station will be replaced.
Tuning in to a station
1
Press POWER to turn on the radio.
2
Press BAND to select the band AM or FM.
3
Press PRESET.
The preset number appears in upper left in the
display.
4
Turn TUNE/SELECT clockwise or
counterclockwise to select the preset number.
5
Adjust the volume using VOLUME.
XDR-S3HD
This section is extracted
from instruction manual.
Tip
The preset can be selected by pressing the number
button of the remote commander. Press ENTER after
the preset number is selected.
—Scan tuning
The unit will automatically scan the selected band.
In HD scan, HD Radio stations are scanned.
1
Press POWER to turn on the radio.
2
Press BAND to select the band AM or FM.
3
Press MENU to show the menu display.
4
Turn TUNE/SELECT clockwise or
counterclockwise to select "SCAN" or "HD
SCAN," then press ENTER.
Scanning of the selected band starts.
When a station is received, scanning pauses for 3
seconds and then continues.
5
When the unit tunes in to the desired station,
do any of the following operations to stop
scanning.
– Press ENTER on the unit or remote commander.
– Press SCAN or HD SCAN on the remote
commander.
6
If necessary, turn TUNE/SELECT
clockwise or counterclockwise to tune in to
the station more precisely.
7
Adjust the volume using VOLUME.
Tip
You can scan a station directly by pressing SCAN or
HD SCAN on the remote commander.
To listen with the
headphones
You can enjoy the radio and external equipment
connected to the line in by the headphones (not
supplied). Connect the headphones (not supplied) to the
i (headphone) jack. The speaker is deactivated when
the headphones are connected.
Changing the
display mode and
settings
To change the display mode
Press DISPLAY.
The display changes as follows:
When an analog radio station is received
x
A Field strength level indicator
B Preset number*
C Band
D Frequency
E Current time
* When you tune in a station by selecting a preset
number.
When an analog FM broadcast that supports
RBDS (Radio Broadcast Data System) is
received
x
x
x
3