Switching Off; Maintenance; Troubleshooting - Black & Decker GD300 Original Instructions Manual

Switching off

To switch the appliance off, release the switch lever (5).

Never attempt to lock a switch in the on position.
Warning! Let the appliance work at its own pace. Do not
overload.
To look after a lawn properly, you need to do more than just
mow it once a week throughout the Summer. The lawn will
benefit from a vigorous raking of the grass to remove the
dead matter, moss and weed which disfigures a lawn. The
build up of dead grass provides a mat of absorbent fibres
which prevents water getting through to the ground and if
this mat is kept waterlogged, it can encourage grass
diseases and prevent healthy grasses taking root.
Place the bulk of the extension cable on the lawn close

to the starting point (Fig. G, position 1).
Hold the handle with both hands and hold the upper

portion of the extension cable in the hand not operating
the switch lever.
Warning! Do not attempt to operate your raker with one
hand - you must guide it with both hands.
Switch on as described above.

Proceed down the raking area from position 1 towards

position 2 and, on reaching position 2, turn to the right
and proceed towards position 3. Continue to the end of
the raking area, turn to the left, and proceed towards
position 4.
Continue in the same manner as shown in the left hand

diagram, always working away from the cable. Do not
adopt the method shown in the right hand diagram,
working towards the cable, as this is dangerous
practice.
When you have finished using your raker we recommend
that you clean all debris from it before putting it away. Refer
to the "Maintenance" section in this manual.
Note: To obtain the best results rake your lawn or grassed
area regularly and do not rake when the grass is wet.
When raking over the edge of your lawn, press

downwards on the handle to stop the wheels dropping
over the edge.
To prolong the effective raking life of your tine

assembly, clear the lawn area of any loose debris or
stones.
Warning! Do not connect a damaged cord to the supply or
touch a damaged cord before it is disconnected from the
supply. A damaged cord can lead to contact with live parts.
Warning! Do not touch the tines before the machine is
disconnected form the supply and the tines have come to a
complete stop.
Warning! Children should be supervised to ensure that they
do not play with the appliance.
8
Warning! This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their
safety.
Hints for optimum use
Do not force your raker through grass that is too long. It is
recommended that your raker should not be used in grass
that is longer that 75mm (3 inches) in length.
Do not use in wet or damp conditions.

To obtain the best result from your raker use it regularly.

It is recommended that your raker is used at the
beginning and end of each grass cutting season to give
your lawn a thorough scarifying. Your raker should also
be used after each mowing session to remove any
grass cuttings that may have been left behind by your
raker.
Rake first in one direct i on and then at the next occasion

at right angles. Initially, this may make the grass look
bare and straggly but it will rapidly recover.

Maintenance

Your Black & Decker appliance has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper appliance care and regular cleaning.
Keep the appliance clean and dry.

Regularly clean the ventilation slots with a clean, dry

paint brush.
Regularly use a blunt scraper to remove grass and dirt

from the appliance.
To clean the appliance, use only mild soap and a damp

cloth. Never let any liquid get inside the tool and never
immerse any part of the tool into liquid. Do not use any
abrasive or solvent-based cleaner.

Troubleshooting

If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local Black & Decker repair agent.
Warning! Before proceeding, remove the plug from the
socket.
Motor buzzes but the tine assembly does not move
Carefully remove any obstructions from the tines.

No noise and tine assembly does not move
Check that the power cables are properly connected.

Check the mains fuses.
