Advertisement
---
ii
n Carefully till washer backward
Jnlil front of washer is 3-J inches off of
lwr. Insert piece of wood as brace.
12
Use legs and ntis from pads
n package. Screw nut down to
vithln l/2" of base.
13
n
nseri legs into
:orrecl holes al
lath front comer
d washer until
buts touch washer.
)o not tiahlen nuis
icrew Ihe front legs up or down lo adjust.
Make final check with level.
Nhen washer is level, use
Nrench to turn nuts on front leg!
JP
tightly against washer base.
f nuts are not tight against
w&y?;
base, tha washer may
Property Damage
Secure the drain hose to the tub or
standplpe with the shlpplng strap
removed from the back of the washer.
Failure to properly secure drain hose
could result In waler damage.
6
I
N
li
sl
tt
C
ki
leasure and mark a poinf approximalely
5 inches from Ihe plug end of the
lipping strap. Cul the shipping slrap al
lis point.
heck that hose Is not twlsted
or
Inked and Is securely
In place.
F
'ul "hook" end of drain hose in tub or
S
landpipe. Tightly wrap the shipping sfrap
a
round the drain hose and tub or
S
tandpipe or inlet hose as shown in
F 'igures A-C. Push plug into the nearest
h 018 in the shipping strap.
14
Tilt washer backward and
H remove wood brace.
Genlly lower washer to floor.
Move washer to Its flnal locatlon.
Remove cardboard
or hardboard
from under washer.
Slide washer onto cardboard
or
hardboard before moving across
floor.
Failure lo do so may cause damage
to floor covering.
adjust rear self-leveling legs. Gently
lower washer lo floor. Check levelness o
!he washer by placing a carpenlets level
,n top of the washer, firs1 side lo side;
hen front lo back.
1
D
u
m
___--
-
Check that hose is not twisted or
kinked and Is securely
In place.
f drain hose cannot be strapped in place,
I musl be cuf exaclly lo len$h so the
'hook" end is held lightly over Ihe edge of
he tub or standpipe.
Me: I, warher Is moved Lo adjurt drain horn, lha
vashsr
mu.,
ba lavalad agaln. Rapea
Slap*
IS-
IS. Place cardboard
under
Lha washer
and
:arefully
move
washor
lo avoid
damaging
floor
:overing.
18
CHECK ELECTRICAL
W REQUIREMENTS.
BE
SURE YOU HAVE CORRECT
:LECTRICAL
SUPPLY AND
3ECOMMENDED
GROUNDING
q Check lhat all oarts are no'
nstalled. See parls list, Panel A. If the1
s an extra part, go back lhrough sleps I
,ee which slep was skipped.
20
Turn on waler faucets and
q check for leaks. Tighlen
ouplings if lhere is leaking.
Check that you have all of
q your tools. Check that the
lipping strapwith 3 colterpins and plug
as removed from Ihe back of Ihe washc
Id used lo secure Ihe drain hose.
22
Untape electrical cord and
W plug into grounded oullet.
23
Take a few minules and
q read Ihe Use and Care
Jide to fully understand your new
isher. Now start the washer and allow
complele the regular cycle.
To get the most efflclent
use
from your washer, read your
KitchenAid
Use and Care
Guide. Keep Installation
lnstrucllons
and Guide close
lo washer for easy reference.
Panel C
Advertisement
