CDA GAS HOBS HCG301 Installation & Use Manual
  1. Manuals
  2. Brands
  3. CDA Manuals
  4. Hob
  5. GAS HOBS HCG301
  6. Installation & use manual

CDA GAS HOBS HCG301 Installation & Use Manual

Domino two burner gas hobs
Hide thumbs
Table of Contents

Advertisement

Quick Links

HCG301 Domino Two Burner
Gas Hobs
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu

Advertisement

Table of Contents
loading

Related Manuals for CDA GAS HOBS HCG301

Summary of Contents for CDA GAS HOBS HCG301

  • Page 1 Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...

  • Page 2: Important Precautions And Recommendations

    ENGLISH Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance. Please preserve this booklet carefully.
  • Page 3 Fig. 1.2 CAUTION: If the burner is accidentally extinguished, turn the gas off at the control knob and wait at least 1 minute before attempting to relight. CAUTION: Gas hobs produce heat and humidity in the environment in which they are installed.
  • Page 4 “2 ELECTRIC” COOKING HOB - Electrical isulation Class I. - Overheating surfaces protection Type Y. COOKING POINTS 1. Electrical plate Ø 145 - (1000 W - 1500 W) 2. Electrical plate Ø 180 - (1500 W - 2000 W) CONTROL PANEL DESCRIPTION 3.

  • Page 5: Gas Burners

    The sparks produced by the lighter situated inside the relative burner will light the flame. In the event that the local gas supply conditions makes it difficult to light the burner in maximum aperture position, try again with the knob in minimum position.

  • Page 6: Choice Of Burner

    A small diameter pot or pan placed on a large burner does not necessarily mean that boiling conditions are reached quicker.
  • Page 7 Fig. 3.1 Fig. 3.2 Hob controlled by Hob controlled by 7-position continuous energy switch regulation switch 0 - 6 0 - 12 Warming Cooking Roasting - Frying Fig. 3.4 ELECTRIC COOKING HOBS NORMAL HOTPLATE To turn on the electric hotplate, rotate the knob (fig. 3.1 - 3.2) o the desired setting. The numbers from 1 to 6 or 1 to 12 indicate the operating positions with increasing number corresponding to higher temperature settings.
  • Page 8 The main characteristic of this pyroceram cooker top is that it permits rapid vertical transmission of the heat from the heating elements below to the saucepans on top. The heat does not spread horizontally, however, and therefore the glass stays cold only a few centimetres from the hob.
  • Page 9 Hob controlled by Hob controlled by 7-position continuous energy switch regulation switch 0 - 6 0 - 12 Warming Cooking Roasting - Frying Fig. 4.6 ELECTRIC HOTPLATE USAGE TABLE Position Type of cooking of switch Switched OFF For melting operations (of but- ter or chocolate) To keep foods warm or heat small quantities of water.

  • Page 10: Cleaning And Maintenance

    CLEANING AND MAINTENANCE GENERAL RECOMANDATION Before you begin cleaning you must ensure that the hob is switched off. It is advisable to clean when the appliance is cold and espe- cially when cleaning the enamelled parts. All enamelled surfaces have to be washed with soapy water or some other non-abrasive product with a sponge and are to be dried preferably with a soft cloth.

  • Page 11: Burners And Grids

    CORRECT REPLACEMENT OF THE BURNERS It is very important to check that the burner flame distributor F and the cap C has been correctly positioned (see figs. 5.2 and 5.6 ) failure to do so can cause serious problems.

  • Page 12: Installation

    Installation advice IMPORTANT – The appliance should be installed, regulated and adapted to function with other types of gas by a QUALIFIED INSTAL- LATION TECHNICIAN. Failure to comply with this condition will render the guaran- tee invalid. – The appliance must be installed in compliance with regula- tions in force.
  • Page 13 Fig. 6.3 Clearance Cupboard door Space for connections Fig. 6.4 Fig. 6.5 Extractor hood for products of combustion Air vent Fig. 6.6 WITH CUPBOARD DOORS The fixture has to be made according to specific requirements in order to prevent the gas burners from going out, even when the flame is turned down to minimum, due to pressure changes while opening or closing the cupboard doors.
  • Page 14 ELECTRICAL PLATES AND VITROCERAMIC COOKING HOBS Fig. 6.8a TECHNICAL INFORMATION FOR THE INSTALLER Before installing the cooktop, remove the protective film. These cooking hobs are designed to be embedded into kitchen fixtures measuring 600 mm in depth and from 20 to 40 mm thick, for 2 electrical plates hob, and from 30 to 40 mm thick for vitroceramic hob.
  • Page 15 Fig. 6.10 Fig. 6.11 Fig. 6.12 FASTENING THE COOKTOP Each cooker top is provided with an installation kit including brackets and screws for fastening the top to fixture panels from 20-30 to 40 mm thick, figs. 6.11 (2 electrical plates hob) e 6.12 (vitroceramic hob). Cut the unit.

  • Page 16: Gas Section

    GAS CONNECTIONS Make sure that the hob is adapted to function with the type of gas supply available (see label). If not, refer to the section headed “Adapting the appliance to function with diffe- rent types of gas”. GASES The gases used for the operation of cooking appliances may be grouped by their cha- racteristics into two types: –...

  • Page 17: Injectors Table

    Using a wrench substitute the nozzle injectors “J” (Fig. 7.3 - 7.4) with those most suitable for the kind of gas for which it is to be used. The burner are conceived in such a way so as not to require the regulation of the primary air.

  • Page 18: Electrical Section

    IMPORTANT: Installation has to be carried out according to the instructions provided by the manufacturer. Incorrect installation might cause harm and damage to people, animals or objects, for which the manufacturer accepts no responsibility. DETAILS Connection to the electric power supply must be carried out by a qualified technician and following the appropriate safety regulations;...
  • Page 19 Fig. 8.1 Fig. 8.2 230 V (L ) Fig. 8.3 230 V Fig. 8.4 REPAIRS REPLACING THE POWER SUPPLY CABLE (for 2 electrical plates and vitroceramic models) Turn the cooktop over and unhook the terminal board cover by inserting a screwdriver into the two hooks “A”...

  • Page 20: Ligação À Rede Eléctrica

    Importante: A instalação deve ser efetuada conforme as instruções do fabricante. Uma instalação erronea pode causar danos às pessoas, animais ou coisas e defronte a tais acontecimentos o fabricante não pode ser considerado responsável. LIGAÇÃO À REDE ELÉCTRICA A ligação à rede eléctrica deve ser feita por técnicos qualifi- cados e em conformidade com as normas vigentes.
  • Page 21 Cod. 1103055 ß1 STRUZIONI PER L’USO • INSTRUCTIONS FOR USE • MODE D’EMPLOI • INSTRUCCIONES PA O • MANUAL DE USO • ISTRUZIONI PER L’USO • INSTRUCTIONS FOR USE • MODE D’EMP TRUCCIONES PARA EL USO • MANUAL DE USO • ISTRUZIONI PER L’USO • INSTRUCTION E •...

Table of Contents