Transceiver Programming; Kpg-4 Description; Programming Software Description - Kenwood TK-768 Service Manual

T1(í68lH
€'
Programming disk (K
REALIGNMENT/
TH'tNÈ
Fis. 1
6-2. KPG-4 Description
(Optional PC programming interface cable)
The KPG4 is reeded to connect the TK-768/H to the
computer. lt has a circuit in the D-subconnector
(25-
pin) case that converts the RS-232C lbgic levelto TTL
level. The KPG-4 plug is connected to external socket
of the TK-768/H and to the computer by a conversion
cable (option)with a 9-pin female connector and a 25-
pin male connector.
6-3. Programming Software Description
KPG-29D is the programming software for the TK-
76BlH, supplied on a 3.5" or 5.25" floppy disk. This soft-
ware runs under MS-DOS (version 3.3 or later) on an
IBM-PCX|, AT, or PS2, or on a compatible machine.
Data can be input to or read from the TK-768/H, and
e d i t e d o n t h e s c r e e n . P r o g r a m m e d d a t a c a n b e
printed.
6. Transceiver Programming
6-1. Introduction
The TK-768/H transceiver is programmed using an
IBM PC or compatible machine, a programming inter-
face (KPG-4), and a programming disk (KPG-29D)' Fig-
ure 1 shows the setup for an IBM PC.
6. iËËtrffiË
6-1. ffiid!
rK-768/H +#{[EID{&ffi nu PC f^i.tHtrt
( 4H*ëil
) ,ffiË& tr È,9Ë ( KPG-4 ) ÍfiffiËfim
(KPc-2eD) frfrffiffirf..fttrÊVffiÍtFáry" áHHK 1
is&i.ïHflfiiÉ,Íàtrl"
(
6-2. KPG-4 ÊtiË,Hf
(frr+, i+HtJ\ffi&& tr Ê,rfr )
ffi KPG-4 iÊÊ rK-768tlHffittFyfi|, &H D 4E!J1S
&#* (25 ft) +á'Ê,+*&Ë,ffi , EIUïE RS-232 frÍiE
€Ê,+Èx TrL Ê,+, KPG-4 -ffiÊlrÉ)kffi^ TK-768/
H fl.ÈFFlffiE, fi -ffiisÊi.tFtrtEfg&ffi -ffi+Ë&È
ffi, frw&#,rHÊ!-ffiË 25 fiÊlAlffiB, F-ffiË e il
f!ëffiE"
6-3. ffiÍE*í+i.r,Hf;
Kpc-2eD ËHï rK-768/H v!ffiffi#l+, u#M&È
frË&, #M#ÊWffifr],ffi, -ffift3.5tfr'
E-ffiË
5.25 tfr. fi#ftqli,'&IBM-PCD(T. AT d PS2 t)l&.
-hi8ïnflÊ!*êtJti&8, Ê Ms-Dos ( 3.3 ffidEfiÍÉ!
ffi*) Ttrfr. ffi.Htu#l+trJura rK-768/I{ 5^trffi4
Á TK-?68/TT
+ËHryffi , * Htr].U&ffiHiffiH, ffiTË
i.qËÊ!ffiffiEID)+IF{J"
Communication port (RS-232C)
24