Table of Contents
Advertisement
Quick Links
XX199-10-01
Enterprise™ and Enterprise Ultra™
Network Controller Setup Guide
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your
requirements or that the operation will be entirely error free or perform precisely as described in the
documentation. This system has not been designed to be used in life-critical situations and must not
be used for this purpose.
Copyright © 2009 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com
Vicon Part No. 8009-8199-10-01
Rev 0509
Advertisement
Table of Contents
Related Manuals for Vicon SMS Enterprise
Summary of Contents for Vicon SMS Enterprise
- Page 1 Enterprise™ and Enterprise Ultra™ Network Controller Setup Guide Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation.
- Page 3 5. Cleaning -(Do not use caustic, abrasive or aerosol The product shows a significant change in performance. cleaners) 18. Replacement Parts - Use only Vicon specified replacement For units that CAN BE DISCONNECTED from the power parts or an approved equivalent to prevent unit damage and source, use a damp cloth for cleaning.
-
Page 4: Table Of Contents
Contents Configuring Your Enterprise Network Controller ..........2 Connecting Power and the Network to the Enterprise Network Controller......... 2 Configuring IP Settings ....................... 3 Logging in to your Network Controller ..................4 Connecting Nodes and Configuring System Resources ............4 Specifications ..................... -
Page 5: Configuring Your Enterprise Network Controller
Configuring Your Enterprise Network Controller Connecting Power and the Network to the Enterprise Network Controller Connecting Power and the Network 1. Connect a grounded power cord to the power connector on the back of the Enterprise or Enterprise Ultra Network Controller. See the images below. 2. -
Page 6: Configuring Ip Settings
Inside the drive door on the Enterprise Ultra 4. For the Enterprise (1U), press the power switch on the back panel to enable power to the power supply. Then press the power switch on the front panel to power on. See the diagrams below. -
Page 7: Logging In To Your Network Controller
manually. The activation and product keys are included on a license label that is shipped with the system. 8. After reviewing the license agreement, click the Apply button to accept it. IMPORTANT: Click the Apply button only once 9. At the Login page, enter the User name “admin.” 10. - Page 8 NOTE: If there are many nodes it is recommended that you power up one node at a time. This will help avoid confusion. 3. Click the Rename link under the drop-down and enter a name that will help you to identify it, e.g.
-
Page 9: Specifications
Specifications The Enterprise Network Controller is a 19” 1U rack mount disk-based network appliance that gives you greater capacity for applications than the basic Network Controller. The Enterprise Ultra Network Controller is a 19” 2U rack mount network appliance that gives you maximum capacity for applications of greater scale and complexity. -
Page 10: Reset Switches And Drive Lights
Reset Switches and Drive Lights Open the Enterprise Ultra lockable hard drive door, or the Enterprise front cover. See the images below. The table beneath explains the functions of the switches and drive lights. Behind the Enterprise Front Cover Inside the Enterprise front cover. Behind the Enterprise Ultra Drive Door Inside the Enterprise Ultra lockable drive door. -
Page 11: Hard Drives
Hard Drives The Enterprise Network Controller comes equipped with an 80 gigabyte hard drive. This drive can be replaced, but the unit must first be powered down. The Enterprise Ultra Network Controller comes equipped with hot swappable RAID-1 mirrored drives. The drives are 80 Gigabytes each. If a drive is not functioning properly, the drive light shows red or does not light up at all. -
Page 12: Migrating From A Basic Network Controller To An Enterprise Network Controller
Migrating from a Basic Network Controller to an Enterprise Network Controller If you are upgrading your solid-state, basic Network Controller system by migrating to a disk-based Enterprise or Enterprise Ultra, complete the following procedures. You will need to replace the Controller/Node blade circuit card that is currently in your solid-state system with a Node-only card. - Page 13 NOTE: The default IP address of an Enterprise controller is 192.168.0.250. If you changed this in previous steps then enter the new address here. 4. At the Login page enter the User name “admin.” 5. Enter the Password “admin.” 6. Click Go. The security application will now display. 7.
- Page 14 3. Click Full Backup. 4. When the backup is complete it is listed in the Existing Backups section. Vicon is a registered trademark of Vicon Industries Inc Enterprise and Enterprise Ultra are trademarks of S2 Security Corporation.
- Page 15 Software supplied either separately or in hardware is furnished on an “As Is” basis. Vicon does not warrant that such software shall be error (bug) free. Software support via telephone, if provided at no cost, may be discontinued at any time without notice at Vicon’s sole discretion.
- Page 16 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Germany vin-videotronic infosystems gmbh...
Need help?
Do you have a question about the SMS Enterprise and is the answer not in the manual?
Questions and answers