Associated Electrics RC12 L3 Setup Sheet
  1. Manuals
  2. Brands
  3. Associated Electrics Manuals
  4. Motorized Toy Car
  5. RC12 L3
  6. Setup sheet
Associated Electrics RC12 L3 Setup Sheet

Associated Electrics RC12 L3 Setup Sheet

Hide thumbs Also See for RC12 L3:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
M I S C . B A G
REMOVE THESE
PARTS FOR:
3656, qty 4
1/8 x 5/16
4015: step 1
unflanged ball bearing
s t e p 1
MOUNTING REAR TIRES
Install both #3627 rear tires to the hubs
with three #6285 screws into each
wheel hub.
3627
6285
S I D E V I E W S H O W N
s t e p 2
DIFFERENTIAL ADJUSTMENT
While holding rear wheels with your hands, use your right thumb
and index finger to try and rotate the spur gear. The spur gear
should be very difficult to rotate. If you can rotate it easily, then
tighten the #4185 11/32" nut at the end of the axle, a little at a
time, until the spur gear is difficult to rotate.
1:1
1:1
1:1
6285, qty 6
4187, qty 2
4-40 x1/4
washer
steel
MOUNTING FRONT TIRES
Put a # 3656 unflanged ball bearing into each side of the front wheels.
Place a #4187 washer over the axle, then slide the wheel on and secure it with a #6299 E-
clip. Install the other wheel the same way.
1:1
6299, qty 2
E-clip
3627, qty 2
rear wheel/tire
chassis
T O P V I E W S H O W N
3673, qty 2
front wheel/tire
3656
4187
T O O L S U S E D
3/32"
3673 front tire
wheel rib
3656
6299
11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RC12 L3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Associated Electrics RC12 L3

Summary of Contents for Associated Electrics RC12 L3

  • Page 1 M I S C . B A G T O O L S U S E D REMOVE THESE PARTS FOR: 3/32" 6285, qty 6 4187, qty 2 6299, qty 2 3656, qty 4 1/8 x 5/16 4-40 x1/4 washer E-clip 4015: step 1 unflanged ball bearing...
  • Page 2 B A G E T O O L S U S E D REMOVE THESE PARTS FOR: 8435, qty 2 4449, qty 2 4145, qty 4 7337, qty 4 4448 qty 2 6934, qty 2 3760, qty 1 3760, qty 1 servo mounting 4-40 locknut 4-40 x 5/16...

  • Page 3: Steering Linkage

    B A G E T O O L S U S E D REMOVE THESE PARTS FOR: 6274, qty 4 6332, qty 6 6280, qty 2 3323, qty 2 ball cup body clip 8-32 x 1/2 #8 alum.washer 4015: steps 3-4 7320, qty 2 large body washer 3320, qty 2...
  • Page 4 B A G E T O O L S U S E D REMOVE THESE PARTS FOR: 6726, qty 1 7337, qty 2 6515, qty 2 servo tape strip washer 3mm x 10mm 4015: steps 5-6 gold 4510, qty 1 4510, qty 1 roll over antenna antenna cap...

  • Page 5: Radio Adjustments

    .INAL ADJUSTMENTS MAKE THESE ADJUSTMENTS BEFORE RACING SETTING THE TWEAK EXACT SAME TIME. Always loosen one screw first, measurement to find the centerline of the chassis. We set the “tweak” after EVERYTHING ex- then tighten the opposite screw the same amount. 2 Scratch a mark at the centerline at the front of the chassis with your hobby knife.

  • Page 6: Radio Maintenance

    BATTERY CHARGING & Associated recommends the use of a good DISCHARGING. To maintain performance quality automatic peak detection type charger. Peak from your battery packs, it is recommended you DISCHARGING detection chargers will automatically sense when completely discharge them between charges. There The battery packs used for R/C cars are six- the battery pack is fully charged and shut off, thus are several inexpensive discharges available at your...
  • Page 7 CAMBER Excessive negative camber will is a word describing the angle at decrease traction but increase sta- which the tire and wheel rides relative to the ground bility. Positive camber will do the when looked at from the front or back. This is one same.

  • Page 8: Team Associated Online

    REAR AXLE HEIGHT ADJUSTERS Your car comes with four sets of rear axle height adjuster inserts. These inserts allow you to raise or lower the height of the back of the car without The #4-up position allows you to use the maximum diameter tire and the #4-down position requires you to changing tire diameters.

  • Page 9: Setup Sheet

    TIRES/WHEELS FRONT REAR TIRE TYPE TIRE DIAMETER STAGGER WHEEL TYPE TRACK WIDTH (car) TIRE TREATMENT TYPE SHADE IN AMOUNT OF TIRE TREATMENT: SETUP SHEET FRONT REAR outside inside inside outside DATE: _________________ DRIVER: ______________________________________________ TRACK NAME: ________________________________________ EVENT: ______________________________________________ .RONT END FRONT CASTER circle one: FRONT SUSP.

  • Page 10: Ordering Info

    I.D. Replacement tips prepaid by International Money Order in U.S. funds. available! available! available! available! available! 6. Mail to: 6. Mail to: 6. Mail to: 6. Mail to: 6. Mail to: Associated Electrics, Inc., 3585 Cadillac Ave., Costa Mesa, CA 92626 USA.

This manual is also suitable for:

4015 rc12 l3

Table of Contents