Download  Print this page

Personal Safety; Environmental Safety; Cleaning And Disposal - Black & Decker VP510 Instruction Manual

7.2 volt cordless detail sander
Hide thumbs

Advertisement

380850/VP510
5/1/02
11:00 AM
• Charge batteries only with VersaPak battery charger.
2
• Do not use charger in wet or damp conditions. It is intended for indoor use only.
Do not use near sinks, tubs, or the like. Do not immerse in water.
• Do not use charger for any uses other than charging VersaPak batteries. Other
batteries may explode.
• Do not operate charger with damaged cord or plug — have them replaced
immediately.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified Black & Decker service center.
• Do not disassemble charger; take it to a qualified Black & Decker service center
when service or repair is required. Incorrect reassembly may result in risk of
electric shock or fire. There are no consumer serviceable parts inside.
• For best results, do not charge batteries when they or air temperature is BELOW
+40°F or ABOVE +105°F.
• The charger is designed to operate on standard household electrical power (120
volts AC only). Do not attempt to use it on any other voltage.
• Unplug charger when not in use.
• Do not abuse charger cord. To reduce the risk of damage to electric plug and cord,
never carry charger by cord or yank it to disconnect from receptacle.Keep charger
cord from heat, oil, and sharp edges.
• Use only charger supplied by the manufacture to recharge.
PRECAUTIONS WHEN SANDING PAINT
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of
controlling the contaminated dust. The greatest danger of lead poisoning is to
children and pregnant women.
Since it is difficult to identify whether or not a paint contains lead without a
chemical analysis, we recommend the following precautions when sanding any
paint:
A. PERSONAL SAFETY
1. No children or pregnant women should enter the work area where the paint
sanding is being done until all clean up is completed.
2. A dust mask or respirator should be worn by all persons entering the work
If you have any questions, call 1-800-54-HOW-TO
Page 4
area. The filter should be replaced daily or whenever the wearer has difficulty
breathing.
NOTE: Only those dust masks suitable for working with lead paint dust and
fumes should be used. Ordinary painting masks do not offer this protection.
See your local hardware dealer for the proper (NIOSH approved) mask.
3. NO EATING, DRINKING or SMOKING should be done in the work area to
prevent ingesting contaminated paint particles. Workers should wash and
clean up BEFORE eating, drinking or smoking. Articles of food, drink, or
smoking should not be left in the work area where dust would settle on them.
B. ENVIRONMENTAL SAFETY
1. Paint should be removed in such a manner as to minimize the amount of dust
generated.
2. Areas where paint removal is occurring should be sealed with plastic sheeting
of 4 mils thickness.
3. Sanding should be done in a manner to reduce tracking of paint dust outside
the work area.
C. CLEANING AND DISPOSAL
1. All surfaces in the work area should be vacuumed and thoroughly cleaned
daily for the duration of the sanding project. Vacuum filter bags should be
changed frequently.
2. Plastic drop cloths should be gathered up and disposed of along with any
dust chips or other removal debris. They should be placed in sealed refuse
receptacles and disposed of through regular trash pick-up procedures. During
clean up, children and pregnant women should be kept away from the
immediate work area.
3. All toys, washable furniture and utensils used by children should be washed
thoroughly before being used again.
SAFETY WARNINGS AND INSTRUCTIONS: SANDERS
ALWAYS WEAR EYE PROTECTION.
Clean dust off your tool periodically.
CAUTION:
Some wood contains preservatives such as copper chromium
arsenate (CCA) which can be toxic. When sanding these
4

Advertisement

loading

  Related Manuals for Black & Decker VP510