Page 2
P H O E N I X G O L D “ S A P P H I R E ” E L E C T R O N I C S L I M I T E D Phoenix Gold warrants to the first consumer/purchaser of a new There are two ways that you may utilize the warranty on a Sapphire Phoenix Gold Sapphire electronic product that it be free from electronic product purchased in the USA.
System (2) SA1.4x & SA1.5x ......13 years of listening enjoyment. Before installing your System (3) SA1.0x & SA3.0x......14 Sapphire amplifier, please take a moment to carefully read the entire manual. It is required reading for the protection of your vehicle and for the maximum performance of your car audio system.
•2 layer Gold plated 2 ounce copper G10 glass Winners Circle. epoxy printed circuit board Team Phoenix Gold is also about having fun. Ask •Muting circuitry assures no turn on/off noise any of the team members and they’ll tell you the same.
Into 4 ohms @ 12/13.8vDC ....75/100 WRMS A WORD ABOUT OUTPUT POWER Into 2 ohms @ 12/13.8vDC ....110/150 WRMS At Phoenix Gold, we rate power output of an amplifier Bridged into 4 ohms @ 12vDC ..220/300 WRMS at two different voltages. Without your engine Total Dynamic Power ........480 Watts...
10 gauge speaker wire. We suggest 4. RCA Inputs: This two channel amplifier has left and right pre amp termination with a Phoenix Gold PRO404 spade terminal. inputs. Typically all CD players and AM/FM cassette decks...
10 gauge speaker wire. We suggest 4. RCA Inputs: This four channel amplifier has front & rear pre-amp termination with a Phoenix Gold PRO404 spade terminal. inputs. Typically all CD players and AM/FM cassette decks with RCA connections are compatible.
10 gauge speaker wire. We suggest inputs. When all (4) inputs are used, front and rear channels termination with a Phoenix Gold PRO404 spade terminal. fade and subwoofer is not affected by the preamp fader. All...
Page 9
10 gauge speaker wire. We suggest the amplifier to be turned ON and OFF at the source unit. termination with a Phoenix Gold PRO404 spade terminal for the best 4. RCA Inputs: This two channel amplifier has left and right pre-amp signal connections.
CHOOSING THE RIGHT LOCATION: The Sapphire amplfiers have been designed to dissipate heat very efficiently. However, FIGURE 1 prolonged operation at high volumes or use in low Heat Rises Away From Unit FIGURE 1 impedance systems not utilizing a fan can cause Upright Mount the amplifier to overheat and shut down.
Page 11
Is there enough clearance for the RCA cables and 1. Use the largest gauge power and ground cable connectors? Will the speaker cables be able to available. We recommend Phoenix Gold PRO7R/B or enter the terminal connectors correctly? Does your PS7R/B cable. The barrier strip power terminal can...
GAIN ADJUSTMENT CROSSOVER ADJUSTMENT • SA1.3.0x , SA1.4x AND SA1.5x Begin your adjustments at minimum sensitivity Setting the crossover points in a car is dependent (Gain control at 2V). After selecting “dynamic” on the car's size and the woofers / mid bass music, adjust the volume control on your source drivers being used.
SYSTEM (1) SA1.0 SC320 SC320 Z - R O C K 3.5" DUAL CONE 3.5" DUAL CONE BRIDGED RCA INPUT LEFT RIGHT A1.0 GAIN 2 CHANNEL A M P L I F I E R LEFT RIGHT ST25 ST25 T W E E T E R T W E E T E R SM600 SM600...
6 " C O A X I A L 6 " C O A X I A L This system utilizes one SA1.5x or SA1.4x connected to four Sapphire speakers and utilizes the built-in adjustable 12dB per octave subwoofer crossover...