UK/US The latest drivers and documentation updates for this product are available on Internet. Log on to : www.datalogic.com Su Internet sono disponibili le versioni aggiornate di driver e documentazione di questo prodotto. Questo manuale è disponibile anche nella versione italiana.
USING GRYPHON™ DX30 READERS Gryphon™ guns automatically scan barcodes at a distance. Simply aim and pull the trigger. Code scanning is performed along the center of the light bar emitted from the reading window. This bar must cover the entire code.
WEDGE DISCONNECTING THE CABLE INTERFACE SELECTION Follow the procedure to configure the interface required by your application. USB Interface RS232 Interface Wedge Interface Pen Interface...
As with all USB devices, upon connection, the Host performs several checks by communicating with the Gryphon™. During this phase the green LED on the Gryphon™ reader blinks and normal operations are suspended. Two basic conditions must be met before Gryphon™ is ready to read codes, the correct USB driver must be loaded and sufficient power must be supplied to the reader.
Page 7
First Start-Up Connect Green LED blinks Gryphon™ to Host Load drivers (if requested) Does a dialog box appear Disconnect reader Green LED off warning that Bus at Host power is not sufficient? Connect external power supply to cable and power up...
USB INTERFACE SELECTION USB-KBD Ì$+UA03$-:Î USB-KBD-ALT-MODE Ì$+UA04$-@Î USB-KBD-APPLE Ì$+UA05$-FÎ USB-COM* Ì$+UA02$-4Î USB-IBM-Table Top Ì$+UA00$-(Î USB-IBM-Hand Held Ì$+UA01$-.Î * When configuring USB-COM, the relevant files and drivers must be installed from the USB Device Installation software, which downloaded from site http://www.datalogic.com.
USB KEYBOARD NATIONALITY USB-KBD users should select one of the following keyboard nationality codes. Belge Ì$+FJ7$-8Î Deutsch Ì$+FJ3$-$Î English Ì$+FJ4$-)Î Español Ì$+FJ6$-3Î Français Ì$+FJ2$-ÊÎ Italiano Ì$+FJ1$-ÅÎ Svenskt Ì$+FJ5$-.Î Ì$+FJ0$-|Î Japanese Ì$+FJ8$-=Î...
RS232 READER CONFIGURATION Read the restore default code, then read the interface selection code for your application. RESTORE DEFAULT Ì$+$*oÎ RS232 Standard Ì$+CP0$-$Î POS SYSTEMS Nixdorf Mode A Ì$+CM2EC0$->Î Fujitsu Ì$+CM1$-ÈÎ ICL Mode Ì$+CM0$-ÃÎ...
Page 11
WEDGE READER CONFIGURATION Read the restore default code, then read the interface selection code for your application. RESTORE DEFAULT Ì$+$*oÎ WEDGE IBM AT or PS/2 PCs Ì$+CP500$-aÎ IBM XT Ì$+CP503$-vÎ PC Notebook Ì$+CP505$-ÈÎ IBM SURE1 Ì$+CP506$-$Î IBM Terminal 3153 Ì$+CP504$-}Î...
WEDGE (CONTINUED) IBM Terminals 31xx, 32xx, 34xx, 37xx: To select the interface for these IBM Terminals, read the correct key transmission code. Select the keyboard type if necessary (default = advanced keyboard). KEY TRANSMISSION MODE make-only keyboard Ì$+CP502$-oÎ make-break keyboard Ì$+CP501$-hÎ...
WEDGE KEYBOARD NATIONALITY Wedge users should select one of the following wedge keyboard nationality codes. Belge Ì$+FJ7$-8Î Deutsch Ì$+FJ3$-$Î English Ì$+FJ4$-)Î Español Ì$+FJ6$-3Î Français Ì$+FJ2$-ÊÎ Italiano Ì$+FJ1$-ÅÎ Svenskt Ì$+FJ5$-.Î Ì$+FJ0$-|Î The following Keyboard Nationality selection is only valid for IBM AT compatible PCs: Japanese Ì$+FJ8$-=Î...
PEN READER CONFIGURATION Read the restore default code, then read the pen interface selection code. RESTORE DEFAULT Ì$+$*oÎ Ì$+CP6$-BÎ DEFAULT VALUES USB DEFAULT SETTINGS : code identifier disabled, no field adjustment, DATA FORMAT code length not transmitted, character replacement disabled. : USA keyboard, FIFO enabled, inter- KEYBOARD character and inter-code delays disabled, USB keyboard...
RS232 Fujitsu DEFAULT SETTINGS 9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rx timeout 2 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled. : code identifier enabled, no field adjustment, DATA FORMAT code length not transmitted, no header, terminator = CR, character replacement disabled.
0 1 2 3 4 5 6 7 8 4 PDF417 DATALOGIC PDF417 Test Code YOUR READER IS NOW READY TO READ CODES. To change the defaults refer to the “Gryphon™ Dx30/Mx30 Reference Manual”, part number 90ACC1930, or to the DL Sm@rtSet™ Configuration program, both downloadable from the website.
READING DIAGRAMS GRYPHON™ D130 Reading diagram at 25 °C and 300 lux ambient lighting Reading Zones (10° skew angle) 0.13 mm EAN13 M=1 CODE 39 (5 mils) 0.33 mm 0.50 mm (13 mils) (20 mils) (cm) GRYPHON™ D130-LR Reading diagram at 25 °C and 300 lux ambient lighting Reading Zones (10°...
Page 21
GRYPHON™ D230 Reading diagram at 25 °C and 300 lux ambient lighting Reading Zones (10° skew angle) 0.13 mm EAN13 M=1 CODE39 (5 mils) 0.33 mm 0.50 mm (13 mils) (20 mils) (cm) Reading diagram at 25 °C and 300 lux ambient lighting Reading Zones (10°...
Datalogic has the faculty to repair or replace the product, these provisions do not prolong the original warranty term. The warranty does not apply to any product that has been subject to misuse, accidental damage, unauthorized repair or tampering.
COMPLIANCE FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment. This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This...
Page 24
Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el Gryphon D1XX Gryphon D2XX e tutti i suoi modelli and all its models et tous ses modèles und seine modelle y todos sus modelos...