Ricoh CL5000 Quick Installation Manual

QUICK INSTALLATION GUIDE
Please read the Safety Information in Maintenance Guide 1 before using this machine. It
contains important information related to USER SAFETY and PREVENTING EQUIP-
MENT PROBLEMS.
WHERE TO PUT THE PRINTER
The printer's location should be carefully chosen Environments to Avoid
because environmental conditions greatly affect its
performance.
Locations exposed to direct sunlight or strong light
Warning
Dusty areas
• Confirm that the wall outlet is near the machine
Areas with corrosive gases
and freely accessible, so that in event of an
Areas excessively cold, hot, or humid
emergency, it can be unplugged easily.
Locations near an air conditioner or humidifier
• Only connect the machine to the power source
Locations near other electronic equipment
described on this manual.
• Avoid multi-wiring. Locations where the printer might be subjected to
frequent strong vibration
• Do not damage, break or make any
modifications to the power cord. Do not place
Power Connection
heavy objects on it, pull it hard or bend it more
than necessary. These actions could cause an
Connect the power cord to a power source with the following
electric shock or fire.
specifications:
120 V, 60 Hz, 11 A or more
Caution
• Keep the machine away from humidity and dust.
Space Required for Installing the Printer
A fire or an electric shock might occur.
Leave enough space around the printer. This space is necessary to
• Place the machine on a strong and level surface.
operate the printer. The recommended (or minimum) space
Otherwise, the machine might fall and result in
requirement is as follows:
an injury.
• If you use the machine in a confined space,
confirm that there is a continuous flow of air.
Optimum Environmental Conditions
Recommended temperature and humidity
A
%RH
10˚C 80% 27˚C 80%
80
15˚C 70% 25˚C 70%
32˚C
54%
60
40
15˚C 30% 25˚C 30%
15 10˚C 15% 32˚C 15%
A: 10 cm (4 inch) or more
˚C
10 20 30 B: 10 cm (4 inch) or more
C: 55 cm (22 inch) or more
%RH
50˚F 80% 80.6˚F 80%
D: 75 cm (30 inch) or more
80
59˚F 70% 77˚F 70%
89.6˚F
54%
60
40
59˚F 30% 77˚F 30%
15 50˚F 15% 89.6˚F 15%
˚F
50 60 70 80 90
Possible operation range Recommended range
The machine must be level within 5 mm (0.2 inch) both front to
rear and left to right.
To avoid possible build-up of ozone, place this printer in a large well
ventilated room that has an air turnover of more than 30 m 3 (183
cubic inch)/hr/person.
If you use this printer in a cold area, leave the printer on or severe
cold might damage sensitive components inside the printer.
Depending on the temperature and humidity around the machine,
vapor might occur when printing. Thus steam can be seen when
prints come out.
<G071-7503A>
UNPACKING THE PRINTER AND
CHECKING THE CONTENTS OF
THE BOX
Important
Caution
• To prevent an injury, this printer should be lifted
by at least two people.
Check the contents of the box according to the
following list. If one or some items are missing,
please contact your sales or service
representative.
Important
This package does not include an interface cable.
Please purchase one for use with your host
computer. See "Appendix" the in the Administrator
Reference.
MANUALS FOR THIS PRINTER
Quick Installation Guide (This manual)
Maintenance Guide 1
Maintenance Guide 2
B Option Setup Guide
CD-ROM "Printer Drivers and Utilities"
CD-ROM "Operating Instructions"
CD-ROM "DeskTopBinder V2 Lite"
Power Cable
C
Ferrite Core
Fuser Oil Unit
D
ZESX302E
Paper Feed Unit Labels
Additional Documents
Remove the plastic bag.
Lift the printer and move it to the place where
you want to install it.
When lifting the printer, pull out the holding handles from the sides
of the printer, and hold them with at least two people.
Important
When installing the printer to a low position, be
careful not to get your hand or clothes caught under
the printer.
Return the grips into the printer.
Remove adhesive tapes and packing materials
from the printer.
Put the Paper Feed Unit label for Tray 1 on the
front of Tray 1.
ZESX303J
PREPARING THE
DEVELOPMENT UNIT
Warning
• Do not incinerate spilled toner or used toner.
Toner dust is flammable and might ignite when
exposed to an open flame.
• Disposal should take place at an authorized
dealer or an appropriate collection site.
• If you dispose of the used toner containers
yourself, dispose of them according to the local
regulations.
Caution
• Do not eat or swallow toner.
• Keep toner (used or unused) and toner
cartridges out of reach of children.
• Our products are engineered to meet the highest
standards of quality and functionality. When
purchasing expendable supplies, we
recommend using only those provided by an
authorized dealer.
Open the left cover of the printer by pulling the
fasteners ( ).
c
ZESX433E
ZESX306E
Note
The two round fasteners cannot be detached.
From the top, the development units are installed in the order of
black, yellow, cyan, and magenta.
ZESX307E
Remove all of the packing materials with red tags.
Four packing materials are connected together, and there are two
of them. Remove one by one from the top of the units by holding
the packing material, not the wire.
ZESX308E
Detach the connectors from the development
units from the top to the bottom by pressing the
sides of the connectors.
ZESX410J
Remove the development unit by lifting it first as
shown in the illustration ( c ).
ZESX411E
The illustration shows how to remove the black development unit.
The procedure is the same for all four colors.
Important
Be sure to hold the unit with both hands, and then
pull it slowly.
Place the new development unit on a level
surface, and then remove the sealing strip from
the toner cartridge by holding the unit with the
other hand as shown in the illustration.
ZESX417E
Important
Toner is on the tape after removal. Be careful not to
get it on your hands or clothes.