Vx-Trunk System Operating Example; Vxr-1000 Interconnections To Vx-3000; 3. Vxr-1000 Configuration - Vertex VXR-1000 Service Manual

VXR-1000 Trunking Interface Manual
2-3: Interconnections to VX-3000/Configuration
2-3-1: VXR-1000 Internal Jumpers
*JP1004
*JP1005
2-3-2: VX-3000 Internal Jumpers
*JP1003
*JP1004
*JP1005
*JP1006
*JP1007
*JP1008
* Connect a jumper between the shared side
of JP1006/JP1006 and Pin 7 of J1003.
* Connect a jumper between the shared side
of JP1007/JP1008 and Pin 2 of J1005.

2-3-3: VXR-1000 Interconnections to VX-3000

The chart below describes the individual
wire functions for the cable connected be-
tween the D-Sub 9-pin connectors on the
VXR-1000 (J1004) and VX-3000 (J1004).
VXR-1000 DSUB 9-pin
Accessory Connector
Pin 1: GND
Pin 2: Mobile Transmit Audio
Pin 3: Power Supply Control
Pin 4: Mobile PTT Output
Pin 5: Vcc (13.8 V)
Pin 6: Mobile Receive Audio
Pin 7: Mobile COR Detect
Pin 8: Mobile Microphone Audio
Pin 9: Mobile TX detect/Mobile Mic. PTT
3. VXR-1000 C
ONFIGURATION
For operation in a VX-Trunk II environment,
note the following setup tips regarding the
VXR-1000 (set via the CE-22 software):
The VXR-1000's "Pri Timer" option must be
set to a non-zero value by CE-22).
In CE-22, set the TRUNKING mode to OFF (for
VX-Trunk II only; for other Trunking systems
like LTR, this parameter must be set to ON).
Set PTT1 to HIGH.
Other parameters such as Master/Slave and
Sub_Audio may be set via CE-22 per the cus-
tomer's operating requirements.
12
Open
Jumpered
Open
Jumpered
Open
Open
Open
Open
VX-3000
Pin 5 of J1004
Pin 3 of 1004
Pin 8 of J1004
Pin 7 of J1004
Switched
13.8VDC
output from the
Power Switch
Pin 2 of J1004
Pin 4 of J1004
No Connection
No Connection
4. VX-TRUNK S
4-1: Making a Call from the Portable
1. Press the portable's PTT key for longer than
the "Sampling Time" of the VXR-1000, so as
to ensure that the VXR-1000 receives the por-
table's signal, then press "3 *" while transmit-
ting to connect to the VX-Trunk II system.
2. When the "3 *" is completed, immediately re-
lease the portable's PTT key, so as to return
the portable to the receive mode.
3. If the VX-Trunk system receives the connec-
tion command, a double "beep" will be heard
from the portable's speaker.
4. Press the portable's PTT key for longer than
the "Sampling Time" of the VXR-1000, so as
to ensure that the VXR-1000 receives the por-
table's signal, and enter the other unit's 5-digit
subscriber number via the portable's DTMF
pad. Now release the portable's PTT key to
return the portable to the receive mode.
5. When the subscriber number is successfully
received by the VX-Trunk II system, and a
connection thereby initiated, the VX-Trunk II
system will respond, and a double "beep" will
be heard from the speaker of the portable.
4-2: Receiving a Call at the Portable
1. When the mobile connected to the VXR-1000
receives a connection request from the VX-
Trunk II system, it relays a "connection tone"
to the portable. When this happens, press the
PTT key on the portable.
2. Hold in the PTT key on the portable longer
than the "Sampling Time" programmed for
the VXR-1000, then press the DTMF "*" key.
After pressing the "*" key, release the PTT key
on the portable.
3. When the VX-Trunk II system receives the "*"
response from the portable, it will respond,
and a double "beep" will be heard from the
speaker of the portable.
4-3: Terminating a Call from the Portable
1. Press the portable's PTT key.
2. Hold the portable's PTT key for longer than the
"Sampling Time" of the VXR-1000, then press
the "#" key. The call will now be terminated, and
you may release the portable's PTT key.
O
YSTEM PERATING
E
XAMPLE