Bunn H5E-DV PC Installation & Operating Manual
  1. Manuals
  2. Brands
  3. Bunn Manuals
  4. Water Dispenser
  5. H5E-DV PC
  6. Installation & operating manual

Bunn H5E-DV PC Installation & Operating Manual

Hide thumbs Also See for H5E-DV PC:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
H5E-DV PC
INSTALLATION & OPERATING MANUAL
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic
website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates.
Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a paper copy of the required Illustrated Parts Catalog mailed
via U.S. Postal Service.
www.bunn.com
39338.0000E 02/08 ©2006 BUNN-O-MATIC CORPORATION

Advertisement

Table of Contents
loading

Related Manuals for Bunn H5E-DV PC

Summary of Contents for Bunn H5E-DV PC

  • Page 1 PHONE: (217) 529-6601 FAX: (217) 529-6644 To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates.
  • Page 2 SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

  • Page 3: User Notices

    INTRODUCTION This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel above the dispense valve that indicates the status of the dispenser. This equipment is for indoor use, either wall-mounted or on a sturdy counter or shelf. USER NOTICES The notices on this dispenser should be kept in good condition.

  • Page 4: Electrical Requirements

    ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power source until specified in Initial Set-Up. Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements. 120V. A.C. 208 or 240V. A.C. 120V. A.C. GREEN GREEN 120/208 &...

  • Page 5: Plumbing Requirements

    " water supply line. At least 18 inches of an FDA approved flexible beverage tubing, such as reinforced braided polyethylene or silicone, before the dispenser will facilitate movement to clean the countertop. Bunn- O-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

  • Page 6: Initial Setup

    CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. WALL MOUNTED INSTALLATION If the dispenser is wall mounted, the bottom of the dispenser should be at the same height as a counter or table top.

  • Page 7: Operating Controls

    OPERATING CONTROLS P3743 (a) VOLUME SELECTOR BUTTONS Press and release the button corresponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress.

  • Page 8: Level 1 Programming

    PROGRAMMING When power is applied to the dispenser, the display located on the bottom of the main circuit board will show the revision level of the software for 5 seconds, and then go to (-). While the tank is filling, the display will read (FIL).
  • Page 9 NOTE: The dispenser should be at operating temperature before setting dispense volumes. 1. Press and hold the hidden programming button, located under the ® next to the BUNN logo on the front of the dispenser until the 3 LED's begin flashing from the left to the right. Release the button.

  • Page 10: Wiring Diagrams

    120V AC 2 WIRE + GND J3-5 120/208V AC 3 WIRE + GND 120/240V AC 3 WIRE + GND SINGLE PHASE J3-8 J1-11 39333.0000B 10/06 ©2006 BUNN-O-MATIC CORPORATION White Strip-Tac Plus Black Ink Finished Size: 4.5” x 5.6” 39338 110806 ~ 64% Reduction...

Table of Contents