Features Product Overview TV‐IP450PI TRENDnet’s Outdoor 1.3 MP HD PoE IR Speed Dome Network Camera, model TV‐IP450PI, offers powerful 20x optical zoom, 100 m (330 feet) night vision, an IP66 weather rating, and continuous 360 degree PTZ functionality. Record 1.3 Megapixel HD video (1280 x 960) at 30 fps in a space saving H.264 compression format. Manage up to 32 TRENDnet cameras with included complimentary software and mobile apps. A separate mounting bracket is required—install with TRENDnet’s TV‐HC400, TV‐HW400, TV‐HP400, or TV‐ HN400. 1.3 Megapixel HD Record 1280 x 960 at 30 fps in the space saving H.264 compression format Multi‐Language Interface Support for English, French, Spanish, German, and Russian ...
TV‐IP450PI TRENDnet User’s Guide Tamper Detection Cables Receive tamper detection snapshots via email, ftp, or save to Samba client or Micro SD card Connectors for AC power adapter D‐WDR (Not required when PoE Improved image quality and autofocus in high contrast lighting environments with injector is included) Digital Wide Dynamic Range technology Audio Line in, line out, Motion Detection and grounding wires Create motion detection windows with separate sensitivity settings and event triggers Recording Schedule Network cable connection Define a weekly recording schedule ...
TV‐IP450PI TRENDnet User’s Guide Warnings: Plan for Installation It is recommended to use the PoE+ injector that comes with the camera or an IEEE 802.3at compliant PoE+ switch. There are a number of factors involved in successful camera installation. Follow the If the product does not work properly, please contact your dealer or the nearest suggested installation steps and go through the check lists. This guide will help you to service center. Never attempt to disassemble the camera yourself. ...
TV‐IP450PI TRENDnet User’s Guide Sunlight: Avoid direct sun light exposure. Direct sun light will damage the image Setup Camera with CD sensor. If sunlight is necessary for your viewing purposes, provide protection for the image sensor. 1. Insert the Installation CD‐ROM into your computer’s CD‐ROM drive to initiate Lighting: Consider installing your camera faces the same direction of the light the Auto‐Run program. Choose your preferred language and then click the ...
Page 8
TV‐IP450PI TRENDnet User’s Guide 3. Connect the power/network cable new installation*. The password must be between 8 and 16 characters. (Alphanumeric: a‐z, A‐Z, 0‐9, !, @, #, $). *This camera installation wizard is also good for finding the camera if it was setup with DHCP. The IP address may change dynamically with the DHCP setting. If you want to access your camera again and you don’t know the IP address, you can run this camera installation wizard again. If you have already setup the password and want to keep the password unchanged, un‐check the Change Password box and click next to get the link to access your camera.) ** Please save the password for future references. This device does not have a hardware reset function for temper proof purpose. 9. Click here to access to the camera’s web page or click Next for mobile app ...
TV‐IP450PI TRENDnet User’s Guide Logging‐in to the Camera Access Camera through the Web Browser 1. Open the web browser on your computer. In the address bar, enter the IP System Management and Default Settings address you setup through the setup CD or 192.168.10.30. (If you have a DHCP server on your network, the IP address will be assigned dynamically. For It is recommended that you install your camera with the CD that comes with the package example, if you have a home gateway on your network and you plug‐in the and use accompanying TRENDnetVIEW Pro software for Windows computers. If you do camera on the same network, you can find the camera’s IP address on your not have the CD with you, please go to http://www.trendnet.com/support and enter the home gateway.), and then press Enter. model number and download the software. If you didn’t go through the CD installation wizard or you have reset the camera, your camera has following settings: Management IP : 192.168.10.30 or a dynamic assigned address if you connect the camera to your 2. Enter the user name, admin, and the password you setup through the setup CD ...
Page 10
TV‐IP450PI TRENDnet User’s Guide 3. The camera management page will detect if you installed the camera video 4. Click Next to install the plug‐in. streaming plug‐in or not. Click the link to download the plug‐in from the camera. 5. Click Finish to finish the installation. Permission request depends on the Internet security settings of your computer. Click Run to install the plug‐in. Note: for Mac systems, the plug‐in file is stored on the CD or you can download the latest version from http://www.trendnet.com/downloads/camera/mac/WebComponents.zip ...
Page 11
TV‐IP450PI TRENDnet User’s Guide 6. Open the browser and login again. Allow the plug‐in from TRENDnet if Multi‐Language Change your preferred language anytime prompted. The Live View page will show and begin streaming video. Snapshot Click this icon to take a video snapshot Click once to enable zoom. Then, click and drag the area on the picture to zoom in. Click once on picture for 100% Zoom zoom. Click the icon again to disable zoom. The zoom function works in full screen mode as well Click once to start recording. Click it again to stop Recording recording. The status bar will indicate if it is in recording state or not The camera has two video streams: H.264 and MJPEG. Video Stream ...
Page 12
TV‐IP450PI TRENDnet User’s Guide The status bar shows the status you are at, including Status Bar enabled the zoom, recording video, and successfully taking a snapshot The icon expands the PTZ control panel Pan / Tilt / Zoom control panel Zoom in / out Focus close / far 2. Use the PTZ control buttons to move the lens to the desired position. Iris open / close • Pan the speed dome to the right or left. Speed of pan/tile movement • Tilt the speed dome up or down. • Zoom in or out. Presets Use the presets panel to move to previously saved • Refocus the lens. locations ...
Page 13
TV‐IP450PI TRENDnet User’s Guide Calling a Preset position 42 Call pattern 2 103 Call patrol 6 In the PTZ control panel, select a defined preset from the list and click to call the 43 Call pattern 3 104 Call patrol 7 preset. 44 Call pattern 4 105 Call patrol 8 45 One‐touch patrol 92 Start to set limit stops ...
Page 14
TV‐IP450PI TRENDnet User’s Guide 5. Repeat the steps from 3 to 5 to add more presets. Patrols 6. Click to save all the patrol settings. A patrol is a memorized series of preset functions. It can be configured and called on the patrol settings interface. There are up to 8 patrol available for customization. A patrol can be configured with 32 presets. Calling a Patrol route Configure a Patrol route In the PTZ control panel, select a defined patrol from and click to call the patrol. 1. In the PTZ control panel, click to enter the patrol settings interface. 2. Select a patrol number from . Click to add a preset to a patrol path. ...
Page 15
TV‐IP450PI TRENDnet User’s Guide Pattern 5. Click to save the pattern settings. A pattern is a memorized series of pan, tilt, zoom, and preset functions. A pattern can Buttons on the Patterns interface: be called in the pattern settings interface. There are up to 4 patterns available for customization. Buttons Description Start recording a pattern. Configure a Pattern Stop recording a pattern. 1. In the PTZ control panel, click to enter the pattern settings interface. Call the current pattern. 2. Select a pattern number from the list as shown in Error! Reference source not ...
Page 16
TV‐IP450PI TRENDnet User’s Guide Playback Time line You can playback the video recording on the network storage and download the video There is a playback head in the center of the time line represented by a yellow vertical clip and snapshots to your local computer. line. To look for a specific video recording, move the time line by clicking and dragging it. If the recording is short, zoom in by clicking button. Click to zoom out the time scale. If you know the exact time of the day you are looking for, click then enter the time you want to playback. Different types of recordings are identified differently. The scheduled recordings are marked in blue, and the recordings triggered by motion detection are marked in red. Click and drag the time line to move your time manually Click this button to zoom in the scale Click this button to zoom out of the scale Click this button to specify a specific time of the day. ...
Page 17
TV‐IP450PI TRENDnet User’s Guide Play video Click this button to take a snapshot of current playback . Use playback controls to play back the video recordings Click this button to start clipping a video from playback Click this button to stop clipping a video from playback Click this button to play the video Click this button to pause video playback Click this button to stop playback Download sections of a video Click this button to increase playback speed* To save complete video sections or snapshots, you can download the files directly. Click this button to decrease playback speed* ...
Page 18
TV‐IP450PI TRENDnet User’s Guide Download snapshots Log The log of the TV‐IP450PI will be saved on the network storage. You can search the snapshots Click this button to download relevant records and save to your local computer. Select the type of event that triggered the snapshots. Choose the Start Time and End ...
Page 19
TV‐IP450PI TRENDnet User’s Guide System Advanced Settings System Information page shows the camera basic information. Click System then click System Info to show the page. System Device Settings Setup your camera name and location for easy identification. This camera name will also be recognized by other network camera software as the name of this camera. OSD, On Screen Display, the camera name is setting up here as well. Basic Information Device Name: User defined device name Firmware Version: Firmware Version MAC Address: MAC address of the camera System Time: Display the system time Network Information IP Address: IP address of the camera ...
Page 20
TV‐IP450PI TRENDnet User’s Guide software and OSD, On Screen Display. The default is User Accounts the camera’s model name: You can setup up to 16 user accounts to access the camera’s video stream with a web browser or real time video stream (RTSP). Only one administrator account can be setup to configure the camera and cannot be deleted. Location: Label where you installed this camera Authentication RTSP: Camera’s video stream can be accessed with RTSP, Real Time Streaming Protocol. Only the administrator and users can view this video stream. Un‐checking this box will allow everyone access to this video stream without authentication. Default: checked. HTTP: Camera can be accessed via password protected web management interface. Un‐checking this box will allow anyone to access this camera and change its settings. User Accounts ...
Page 21
TV‐IP450PI TRENDnet User’s Guide Time Settings Set Time: Click the calendar icon and manually select the date. The accuracy of the system clock is important for scheduling and accurate logging. You can synchronize the system time with your computer, or automatically check the time Check the Sync. with computer time to copy the accuracy with a network time server (NTP server). time from your computer. Click Save to save the changes Daylight Savings Setup daylight settings for the camera. Daylight Saving Automatic Update Enable DST: Check this box if your time zone has daylight NTP Server: Specify a time server (NTP server) to synchronize savings with. (e.g. pool.ntp.org) Start Time: Enter the date that daylight savings starts Interval: ...
Page 22
TV‐IP450PI TRENDnet User’s Guide Live View Settings Record File Size: This size of live view video recording. You can choose 256MB, 512MB, or 1GB a file. Smaller file Setup daylight settings for system time. size is good for many short recordings. Save Record Files to: By default, files will be saved under your user name, and under the TRENDnet/RecordFiles. Click Browse and choose a new destination if you want to save the file somewhere else. Save Download Files to: By default, files will be saved under your user name, and under the TRENDnet/DownloadFiles. Click Browse and choose a new destination if you want to save the file somewhere else. Picture and Clip Settings By default, files will be saved under your user name, Save Snapshots in live view and under the TRENDnet/CaptureFiles. Click Browse to: and choose a new destination if you want to save the file somewhere else. By default, files will be saved under your user name, Save snapshots when playback to: and under the TRENDnet/PlaybackPics. Click ...
Page 23
Status: Shows the status in firmware upgrade. Click Save to save the changes * TRENDnet may periodically release firmware upgrades that might add features or fix problems associated with your TRENDnet model and version. To find out if there is a firmware upgrade available for your device, please check your TRENDnet model and version using the link. http://www.trendnet.com/downloads/ ...
Page 24
TV‐IP450PI TRENDnet User’s Guide Network Settings Network interface MAC Address: Click this button to reboot this camera. TCP/IP Duplex and Speed: Choose one of the Ethernet duplex and speed to Setup your basic IPv4 and IPv6 network settings on this page. match your network. Default: auto. MTU: Maximum transmission unit. The maximum byte size Ethernet data field. Primary DNS: Enter your first IPv4 or IPv6 DNS server address Secondary DNS: Enter your second IPv4 or IPv6 DNS server address IPv4 DHCP: Check this box if the IP address is assigned by DHCP server. IPv4 Address: Load complete factory default to the camera. Subnet Mask: Network range of the subnet Default Gateway: The default route going further from camera IPv4 ...
Page 25
TV‐IP450PI TRENDnet User’s Guide Port DDNS You can change the service ports number of the camera or disable RTSP Dynamic Domain Name Service, DDNS, allows you to find your camera from the Internet with an easy to remember domain name. or HTTPS services. Port Numbers DDNS HTTP Port: The default web access port. You can change the Enable DDNS: Check this box to enable DDNS Service. port number. However, you cannot disable the web DDNS Type: Select a DDNS service provider. service. The default port number is 80. Server Address: Enter the DDNS server address. RTSP Port: The Real‐Time Streaming Protocol port for video Domain: Enter your registered domain name on selected ...
Page 26
TV‐IP450PI TRENDnet User’s Guide PPPoE Setup PPPoE (ADSL) connection to connect your camera with your ISP, Internet Service Provider. PPPoE (ADSL) Enable PPPoE: Check this box to enable PPPoE connection. Dynamic IP: The IP address provided by ISP User Name: Enter the account name. Password: Enter the password. Confirm: Enter the password again. Click Save to save the changes SNMP SNMP Settings allows you to assign the contact details, location, community name and trap settings for SNMP. This is a networking management protocol used to monitor ...
Page 27
TV‐IP450PI TRENDnet User’s Guide Private‐key Algorithm: Choose the privacy key to encrypt SNMP messages: SNMP V1/V2 DES or AES. Enable SNMPv1: Check this box to enable SNMP v1 management. Private‐key Password: Specify the privacy key between 8 to 32 letters. Enable SNMPv2c: Check this box to enable SNMP v2c management. SNMP Other Settings Read SNMP Community: Specify the password for access the SNMP community for read only access SNMP Port: SNMP service port number. Write SNMP Community: Specify the password for access to the SNMP Click Save to save the changes community with read/write access Trap Address: Specify the IP address for the SNMP trap community Trap Port: Specify the port number for the SNMP trap ...
Page 28
TV‐IP450PI TRENDnet User’s Guide 802.1X IP Address Filter Setup 802.1X for remote authentication service. Set up a list of clients allow only the clients on the list to access this camera or to reject clients on the list from access this camera. IP Address Filter 802.1X Authentication Enable IP Address Filter: Check this box to enable IP address filtering service. Enable IEEE 802.1X: Check this box to enable 802.1X authentication IP Address Filter Type: Choose Forbidden to ban the listed IP addresses or service. Allowed to allow listed host to access this camera. EAPOL version: Extensible Authentication Protocol (EAP) over LAN Add: Click Add to add a user account (EAPoL). Choose version 1 or 2. This version number ...
Page 29
TV‐IP450PI TRENDnet User’s Guide QoS, Quality of Service UPnP Setup traffic prioritization to help smooth out the video stream. You can set the Universal Plug‐and‐Play is a device discovery protocol set. It allows your camera to easily Differentiated Services Code Point be found, for example, on a Windows operation system. (DSCP) bits on outgoing data streams. The QoS ...
Page 30
TV‐IP450PI TRENDnet User’s Guide Video Settings Video Format Adjust the format of video. Frame Rate: Choose the capturing frame rate. The default value is 30 frames per second. Reduce the frame rate to reduce the capture file size. Max. Bitrate: Choose the maximum video sampling bit rate. Default: 4096 Video Format Video Encoding: Choose the video stream you want to modify. H.264 and Frame Interval An I Frame is a frame that records a complete picture. Frames MJPEG videos are always streaming and can be configured between I frames, (P frame or B frame) only records the image separately. differences between two frames. Choose the I Frame Interval here. The default is 60. ...
TV‐IP450PI TRENDnet User’s Guide Audio Display Settings Adjust the audio settings for the camera. Adjust video image quality, lightness, and color settings here. Audio Audio Encoding: G.711ulaw, G.711alaw, MP2L2 and G.726 selectable. Audio Input: Select LineIn or MicIn to adjust volume. Input Volume: Slid the bar to turn up/down the volume. The value ranges from 0 to 100. Click Save to save the changes Display Settings Brightness: Use the slider or enter a number (0‐100) to adjust the image brightness. Default: 50 Contrast: Use the slider or enter a number (0‐100) to adjust the image contrast. Default: 50 ...
Page 32
TV‐IP450PI TRENDnet User’s Guide Display Settings Focus Mode: Auto focus: allows the camera to focus automatically at any time. Manual: use the icon in the live view page to control focus manually. Semi‐auto: cameras focuses only once after pan/tilt/zoom. Minimum Focusing: This function is used to limit the minimum focus distance. The value can be set to 1.5m, 3m, 6m, 10cm and 50cm. Exposure Mode: Auto: ...
Page 33
TV‐IP450PI TRENDnet User’s Guide Shutter Speed In Auto mode, the day mode and night mode can switch automatically according to the light condition of environment. Mirror: Select from OFF or ON option to set the correct direction of the camera view. Slow Shutter: This ...
Page 34
TV‐IP450PI TRENDnet User’s Guide Fluorescent Lamp: When IR Light Mode is set to manual and the IR Light Bright is not 0, night mode is set as the default mode. Manually setting the day/night mode is You can select this mode when there are fluorescent invalid. lamps installed near the speed dome. Sodium Lamp: You can select this mode when there are sodium lamps installed near the speed dome. Auto‐Track: White balance is continuously being adjusted in real‐ time according to the color temperature of the scene illumination. : Enable or disable noise reduction. Digital Noise Reduction Noise Reduction Level: Adjust the effect of digital ...
Page 35
TV‐IP450PI TRENDnet User’s Guide On Screen Display (OSD) Settings Text Overlay You can display the camera name and the time the video is shooting on the screen. Display extra information on the screen over the image. OSD Display Display Name: Check this box to display the product name that was Text Overlay setup in the device settings (refer to page 25 to Check Box: Check this box to enable text overlay. change the device name.) Text Field: Enter the text you want to display. You can enter Display Date: Check this box to display system time. your local language if you want. The text field Display Week: Check this box to display time of the week. allows maximum 44 English letters or 20 non‐ Time Format: Select 12 or 24 hours’ time format.
TV‐IP450PI TRENDnet User’s Guide Video Recording 1. Select day of the week you want to edit the schedule. 2. Select All Day or Customized schedule of the day. 3. Set the time period and the event you want to trigger the video recording continuous (always recording) or motion detection. 4. Click Copy to Week if you want the same ...
TV‐IP450PI TRENDnet User’s Guide Events status of motion detection. The motion tracking is displayed by a green grid. The grid area represents that the camera detects motion in this area. Click Motion Detection Save to save the choices. Set up how the motion detection event will be triggered and what actions will be Draw Area: Click Draw Area button to start drawing. Click and triggered. drag on the area you want to set up the motion detection. You can draw up to 8 different areas. Click Stop Drawing to stop drawing motion detection areas. The red grids represent the detection area. Sensitivity: Move the slider to adjust detection sensitivity. Clear All: Click this button to clear all the set up areas. Motion Detection Enable Motion Detection: Check this box to enable motion detection. Click ...
Page 38
TV‐IP450PI TRENDnet User’s Guide 1. Select day of the week you want to edit the schedule. 2. Set the time period you want to enable motion detection. (Default is 0‐24 hours, all day). 3. Click Copy to Week if you want the same daily schedule every day or you can select ...
TV‐IP450PI TRENDnet User’s Guide Upload to FTP: Check this box to send snapshots to an FTP server Tamper‐proof when motion is detected. Go to Storage / FTP to Enable Tamper Detection: Check this box to enable tamper detection. Click Save setup FTP server information to save the settings. Click Save to save the changes Draw Area: Click Draw Area button to start drawing. Click and drag on the area you want to set up the tamper ...
Page 40
TV‐IP450PI TRENDnet User’s Guide 1. Select the day of the week you want to edit the schedule. 2. Set the time period you want to enable tamper detection. (Default is 0‐24 hours, all day). 3. Click Copy to Week if you want the same daily schedule every day. Or, you can select other day of the week and click Copy to copy ...
TV‐IP450PI TRENDnet User’s Guide Exception Snapshot Provides notifications for other system events, set up your notifications here. You can set up your camera to continuously take snapshots or take snapshots when an event happens. Notification Exception Type: First choose the exception type, then choose the corresponding action. Send Email: Check this box to send an e‐mail notification when motion is detected. Go to Events / Email to setup email account information. Continuous Click Save to save the changes Enable: Check this box to continuously take snapshots. Format: Save snapshots in JPEG format ...
TV‐IP450PI TRENDnet User’s Guide Email Set up email accounts for notifications. Event Triggered Enable: Check this box to take snapshots when an event is occurred. Format: Save snapshots in JPEG format Resolution: Uses the same resolution set in Video Format for the snapshot resolution. Quality: Choose a compression quality for snapshot. Interval: State the time interval between this series of snapshots. The default interval is 1 second. Capture Number: State how many snapshots you want to take in a ...
TV‐IP450PI TRENDnet User’s Guide Check this box if your service provider requires a Storage Enable SSL: SSL secured connection. Attach Image/Interval: Check Attach Image if you want to send a snapshot Storage Management image with the email notification and select the * Micro SD card or Network storage device must be setup / formatted before it can be interval of snapshots in seconds. managed / stored. Camera will save to SD card only when there is no additional NAS Authentication: Check this box if your server requires a password in device setup. order to send email. Most email servers require authentication when sending an email. User name: Enter the user name of outgoing email account Password: Enter the password Confirm: Enter the password again to confirm that the password was entered correctly. Click Save to save the changes ...
TV‐IP450PI TRENDnet User’s Guide User Name: Enter the user name if the network storage requires authentication. Leave it blank if no authentication is required. Password: Enter the password to access the network storage. Tip: To create network storage on your Windows® based system, create a shared folder and then test your set up with another computer. Enter the IP address of the computer here and enter the shared folder name with a leading forward slash. For ...
TV‐IP450PI TRENDnet User’s Guide Pan/Tilt/Zoom (PTZ) Settings FTP Enable Snapshot to FTP: Check this box if you want to store snapshots on Basic the FTP. Server Address: Enter the FTP server IP address. Port: Enter the service port number of the FTP server. User Name/Anonymous: Check Anonymous if the FTP server does not require authentication. Enter the User Name if the FTP server requires authentication. Password: Enter the password of the FTP account. Confirm: Enter the password again to make sure the password was entered correctly. Directory Structure: When saving snapshots on an FTP server, they can be saved in a single place or organized with meaningful directory names. Save in root directory: You can choose to store all files in the same folder of FTP login. ...
TV‐IP450PI TRENDnet User’s Guide Max. Tilt‐angle: The maximum angle that the camera can revolve in Limit the tilt direction is adjustable. The values range The camera can be programmed to move within the configured stops. (left, right, up or down) from (0‐90) to (‐5‐90) Auto Flip: You can enable/disable the auto flip function PTZ OSD Zoom Status: Set the OSD duration of zooming status as 2 seconds to 10 seconds, always on or off. PT Status: Set the angle display duration white panning and tilting as 2 seconds to 10 seconds, always on or off. Preset Status: Set the preset name display duration as 2 seconds to 10 seconds, always on or off. POWER OFF MEMORY Set Resume Time Point: The camera can resume its previous PTZ status or actions after it is restarted from a power‐off. You ...
TV‐IP450PI TRENDnet User’s Guide Initial Position Park Action Set the camera initial position, you can also call a preset for the position. Click Set to The feature allows the camera to start at a predefined park action. (scan, preset, pattern) automatically after a period of inactivity (park time). save the limits and Clear to clear the limits. Scheduled Tasks function has higher priority over Park Action function therefore when two functions are set at the same time, Scheduled Tasks function takes effect. ...
TV‐IP450PI TRENDnet User’s Guide immediately as prolonged exposure to bright lights will damage the CMOS Troubleshooting sensor. 1. The camera can’t be accessed or access is slow 4. The camera images are ‘noisy’ There might be a problem with the network cable. To confirm that the cables Often if the camera is in a low‐light environment, the images can contain a lot of are working, ping the address of a known device on the network. If the cabling noise. Try enabling Night mode and see if that improves the image quality. ...
Page 51
TV‐IP450PI TRENDnet User’s Guide Federal Communication Commission Interference Statement EN 60950‐1:2006+A11:2009+A1:2010+A12:2011 This equipment has been tested and found to comply with the limits for a Class B digital Safety of Information Technology Equipment device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide EN 62311: 2008 reasonable protection against harmful interference in a residential installation. This ...
Page 53
TV‐IP450PI TRENDnet User’s Guide Česky TRENDnet tímto prohlašuje, že tento TV‐IP450PI je ve shodě se Latviski Ar šo TRENDnet deklarē, ka TV‐IP450PI atbilst Direktīvas [Czech] základními požadavky a dalšími příslušnými ustanoveními [Latvian] 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem směrnice 1999/5/ES. noteikumiem. Dansk Undertegnede TRENDnet erklærer herved, at følgende udstyr Lietuvių Šiuo TRENDnet deklaruoja, kad šis TV‐IP450PI atitinka esminius [Danish] TV‐ TV‐IP450PI overholder de væsentlige krav og øvrige [Lithuanian] reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. relevante krav i direktiv 1999/5/EF. Hierbij verklaart TRENDnet dat het toestel TV‐IP450PI in Deutsch Hiermit erklärt TRENDnet, dass sich das Gerät TV‐IP450PI in Nederlands overeenstemming is met de essentiële eisen en de andere [German] Übereinstimmung mit den grundlegenden Anforderungen und [Dutch] ...
Page 54
Governing Law: This Limited Warranty shall be governed by the laws of the state of for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have California. the RMA number marked on the outside of return packages and sent to TRENDnet Some TRENDnet products include software code written by third party developers. These prepaid, insured and packaged appropriately for safe shipment. Customers shipping from codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public outside of the USA and Canada are responsible for return shipping fees. Customers ...