Service Recommendations; Environmental Information - Flymo Micro Lite User Instructions

• It is very important that you keep your product clean.
Grass clippings left in any of the air intakes or under
the hood could become a potential fire hazard
Cleaning (Q)
1. Remove grass from under the hood with a piece of
wood or similar.
2. Using a soft brush - remove grass clippings from all
air intakes.
3. Remove the cutting head, (see fig K), to gain access
to the fan and clean with a soft brush.
4. Wipe over the surface of your product with a dry cloth.
• IMPORTANT: Never use water for cleaning your
product. Do not clean with chemicals, including
petrol, or solvents - some can destroy critical plastic
parts.
At the End of the Cutting Season
1. Replace plastic cutters, bolts, nuts or screws, if necessary.
2. Clean your product thoroughly.
3. Ask your local Service Centre to clean the air filter thor-
oughly and carry out any service or repairs required.
4. Make sure that the electric cable is coiled properly.
Carrying your Product: Hold as illustrated in Figure R. En-
sure the blade is facing away from you.
Storing your Product (S): Store in a dry place where your
product is protected from damage.
Fails to Operate
1. Is the Power Turned On?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
Immediately disconnect from the mains electricity
supply and consult your local approved Service
Centre.
Poor Flotation
1. Disconnect from the mains electricity supply.
2. Clean the underside of the hood and the fan blades.
3. Raise to a higher height of cut. See Adjusting the
Cutting Height.
1. We strongly recommend that your product is serv-
iced at least every twelve months, more often in a
professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most Husq-
varna UK Ltd. stockists.
4. Your product is uniquely identified by a silver and
black product rating label
5. If you have a problem with your machine contact
your local Approved Service Centre ensuring you
have full details of your product as described on the
product rating label.
6. Should it be necessary for work to be carried out by
Husqvarna UK Ltd. are manufactured under an Environ-
mental Management System (ISO 14001) using, where
practical, components manufactured in the most environ-
mentally responsible manner, according to company pro-
cedures, and with the potential for recycling at the end of
the products' life.
• Packaging is recyclable and plastic components have
been labelled (where practical) for categorised recy-
cling.
• Awareness of the environment must be considered
when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal
information.
Caring for your Product
Q
R
Fault Finding Hints
4.
Excessive Vibration
1.
2.
3.
4.

Service Recommendations

A network of specialist dealers can be found in your local
Yellow Pages.
To obtain service on your Flymo product simply tele-
phone or visit your local Service Centre.
Should you require service under the terms of our guarantee
the Service Centre will require proof of purchase.
All of the centres listed stock genuine Flymo Spare Parts.
NOTE: Our Service Repairers act on their own behalf
and are not empowered to commit or legally bind Husq-
varna UK Ltd. in any manner whatsoever.

Environmental Information

The symbol
cates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and elec-
tronic equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the envi-
ronment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or the shop where you
purchased the product.
If poor flotation persists?
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Disconnect from the mains electricity supply.
Replace broken or missing plastic cutters.
Check plastic cutters and cutting head are fitted cor-
rectly and securely located.
If vibration persists?
Immediately disconnect from the mains electricity
supply and consult your local approved Service
Centre.
your Service Centre, it is important to take your com-
plete machine including cable and any extension ca-
bles used.
on the product or on its packaging indi-
S