Download Print this page

Casio 5226 Operation Manual

Hide thumbs


Quick Links

Your watch may differ somewhat from the one shown in the illustration.
Hour hand
Stopwatch hour hand
Stopwatch second hand
To set the time
When the second hand is at 12 o'clock, pull out the crown to the second click
to stop it.
Set the hands by rotating the crown. Move the minute hand four or five minutes
past the setting you want, and then back them up to the setting.
Push the crown back in on a time signal to resume timekeeping.
To set the day and day of the week
Avoid setting the day and day of the week between 9:00 p.m. and 6:00 a.m. The
day and day of the week may not change in the following day if you do.
Pull out the crown to the first click.
Set the day by rotating the crown counterclockwise.
Set the day of the week by rotating the crown clockwise.
Push the crown back in to its normal position.
Using the Stopwatch
The stopwatch lets you measure elapsed time up to 11 hours, 59 minutes,
59 seconds.
The illustration shows a time of 2 hours, 20 minutes, 40 seconds.
Do not try to perform stopwatch operations while the crown is pulled out either
to the first or second click. If you try to press a button, you might accidentally
cause the crown to rotate and change the current time or day setting.
Once started, stopwatch timing continues until you press
if timing reaches the stopwatch limit defined above.
To measure elapsed time
A to start the stopwatch.
A to stop the stopwatch.
You can resume the measurement operation by pressing
B to reset the stopwatch.
Adjusting the Stopwatch Hands Position
Use of the stopwatch can cause the starting positions of the stopwatch hour
hand, minute hand and second hand to become misaligned. Use the following
procedures to check hand alignment and to adjust the positions of the hands so
they point to 12 o'clock when the stopwatch is reset.
To adjust the positions of the stopwatch hands
B to reset the stopwatch, and check the alignment of the stopwatch
hour hand, minute hand and second hand.
Pull out the crown to the second click.
A to move the stopwatch second hand forward until it points to
12 o'clock.
If the stopwatch minute hand is aligned correctly, proceed to step 5. If the
stopwatch hour hand and stopwatch minute hand are also misaligned, press B
so the stopwatch hour hand and the stopwatch minute hand jump to 12 (60).
After making the adjustments you want, push the crown back in to its normal
Note that pulling the crown out also stops the timekeeping second hand. After
performing the above procedure, you should also adjust the timekeeping setting.
For a watch with an elapsed time bezel
Rotate the elapsed time bezel to align the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
Some water resistant models are equipped with a screw
lock crown.
With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
Also note that such watches are not water resistant while
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
3 dials (timekeeping seconds, stopwatch hours and minutes), day, day of the
Stopwatch function: Measuring capacity: 11:59'59"
Measuring unit: 1 second
Measuring modes: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 5 years on type SR927W (assuming one stopwatch operation 60 min./day)
Operation Guide 5226
Stopwatch minute hand
Minute hand
First click
(Day, day of week setting)
Second click
(Time setting)
(Normal position)
Second hand
Day of week
A to stop it and even
A again.
mark with the
Elapsed time bezel