Advertisement
Operation Guide 5157
B until the month digits start to fl ash, which
1.
In the Calendar Mode, hold down
indicates the setting screen.
C to increase the month digits.
2.
Press
B to move the selection to the day digits.
3.
Press
C to increase the day digits.
4.
Press
B to move the selection to the day of the week.
5.
Press
C to advance to the next day.
6.
Press
B to exit the setting screen.
7.
Press
The watch does not make any allowance for leap years. Be sure to manually set
February 29 when one occurs during a leap year.
E-10
To set the alarm time and to turn the Daily Alarm and Hourly Time Signal on
and off
Mode indicator
Alarm on indicator
Alarm time
(Hour : Minutes)
Hourly time signal on indicator
E-12
Press
Press
C.
C.
Both ON
Both OFF
Press C.
B to exit the setting screen.
9.
Press
To stop the alarm
Press any button to stop the alarm after it starts to sound.
E-14
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone.
In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode digital time.
E-16
B until the hour digits start to fl ash, which
1.
In the Dual Time Mode, hold down
indicates the setting screen.
C to increase the hour digits.
2.
Press
B to move the selection to the minutes digits.
3.
Press
C to increase the minutes digits.
4.
Press
B to move the selection to 12/24.
5.
Press
C to toggle the timekeeping format between 12-hour and 24-hour.
6.
Press
B to exit the setting screen.
7.
Press
With the 12-hour format, the P (PM) indicator appears on the display for times in
the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
E-18
Press
C.
Daily Alarm only
Hourly Time
Signal only
Alarm
When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset time
each day. When the Hourly Time Signal is turned on, the watch beeps every hour on
the hour.
You can confi gure alarm settings and Hourly Time Signal settings in the Alarm
Mode, which you enter by pressing C (page E-5).
B until the hour digits start to fl ash, which indicates
1.
In the Alarm Mode, hold down
the setting screen.
C to increase the hour digits.
2.
Press
The 12/24-hour format of the alarm time matches the format you select for normal
timekeeping.
B to move the selection to the left minutes digit.
3.
Press
C to increase the left minutes digit.
4.
Press
B to move the selection to the right minutes digit.
5.
Press
C to increase the right minutes digit.
6.
Press
B to move to the Daily Alarm and Hourly Time Signal on and off setting.
7.
Press
C to cycle through the Daily Alarm and Hourly Time Signal settings as
8.
Press
shown in the sequence below.
At this time Daily Alarm and Hourly Time Signal automatically turn on.
To test the alarm and select an alarm tone
Hold down C in any mode (except when making any settings) to sound the alarm.
Note that the alarm sound changes each time you hold down C to test the alarm.
There are a total of four different alarm sounds. The last alarm sound you hear when
performing the above test is the one that is used for the Daily Alarm and the Hourly
Time Signal.
Note that holding down C also changes the mode.
To set the Dual Time
Mode indicator
Hour
Seconds
Minutes
Stopwatch
The Stopwatch Mode lets you measure elapsed time. The
Mode indicator
range of the stopwatch is 59 minutes, 59.99 seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
To use the Stopwatch
1.
In the Stopwatch Mode, press
stopwatch.
B to stop the time measurement.
2.
Press
You can press B as many times as you want to
Minutes
1/100
resume and stop timing.
second
3.
After you are fi nished using the stopwatch, hold down
Seconds
B to clear the stopwatch time to all zeros.
E-11
E-13
E-15
E-17
B to start the
E-19
Advertisement
