Download Print this page

Advertisement

Quick Links

MA1202-EB
Your watch may differ somewhat from the one shown in the illustration.
Celestial window
Star ornament
To set the time
1.
Pull out the crown to the second click.
This will cause the second hand to stop.
2.
Set the hands by rotating the crown. Move the minute hand four or fi ve minutes
past the time you want to set, and then back it up to the proper setting.
Carefully set the time, making sure to distinguish between AM and PM.
3.
Push the crown back in to the normal position to restart timekeeping.
This will cause the second hand to restart.
To set the day
1.
Pull out the crown to the fi rst click.
2.
Set the day by rotating the crown.
3.
Push the crown back in to the normal position.
Avoid setting the day between 9:00 p.m. and 1:00 a.m. (the day display may not
change in the following day).
24-Hour Hand
The 24-Hour Hand indicates the current hour of the day, making one complete
rotation every 24 hours. The hand points to the moon fi gure at midnight and the
sun fi gure at noon.
Star Ornament
The star ornament rotates once every hour*, and twice every six hours*.
* The timing of star ornament rotation is based on when you press A to start it.
Example: When A is pressed at 0:25 to start star ornament rotation
The star will rotate once at 1:25, 2:25, etc. It rotate twice at 6:25, 12:25, etc.
The fi gures in the celestial window move slowly, synchronized with the movement
of the star ornament.
You can disable the above movement, if you like.
While the star ornament is stopped, you can change its orientation.
To disable celestial window and star ornament movement
1.
Pull out the crown to the second click.
This will cause the second hand to stop.
2.
Push the crown back in to its normal position.
This will cause the second hand to start moving again.
Pulling the crown out further will cause the hour, minute, and second hands to
stop. At this time you can adjust the current time setting.
To restart celestial window and star ornament movement
Press A.
This will cause the star ornament to rotate twice.
To stop the star ornament and change its orientation
1.
Pull out the crown to the second click.
This will cause the second hand to stop.
A (rotate right) and B (rotate left) to adjust the orientation of the star
2.
Use
ornament.
Holding down either button causes the star ornament to rotate and high
speed.
3.
After the position is the way you want, press the crown back in to its normal
position.
This will cause the second hand to start moving again.
Pulling the crown out further will cause the hour, minute, and second hands to
stop. At this time you can adjust the current time setting.
For a watch with an elapsed time bezel
Rotate the elapsed time bezel to align the
minute hand.
After that, you will be able to determine how much time has
elapsed since you adjusted the bezel position by checking the
bezel value that the minute hand is currently pointing to.
Some water resistant models are equipped with a screw
lock crown.
With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
Note that a screw lock crown watch is not water resistant
while its crown is loose. Be sure to screw the crown back in
as far as it will go after confi guring settings.
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (hour, minute, second),
1 dial (24-hour), celestial window, star ornament, day
Battery: One silver oxide battery (Type: SR621SW)
Approximately 2 years on type SR621SW
Operation Guide 5246
Second hand
Hour hand
Minute hand
First click
(Day setting)
Second click
(Time setting)
Crown
24-hour hand
(Normal position)
Day
mark with the
Elapsed time bezel
Specifi cations
1

Advertisement

loading