Kenwood FM Transceiver TK-481 Service Manual page 8

4-5. Radio password
When the password is set in the transceiver, user can not
use the transceiver unless enter the correct password.
This code can be up to 6 digits from 0 to 9 and input with
the keypad or selector, and "S" key.
4-6. Battery Warning
This transceiver has battery warning feature. If the low
voltage is detected during transmission, the transceiver
warns it by flashing red "LED".
Then more low voltage is detected during transmission,
the transceiver stops transmission and warns it by flashing
red "LED" and beep.
Please notice "standard" for the battery exchange,
charging time by flashing red LED and beep.
4-7. Minimum Volume
The minimum volume is programmable (off (0) to 31).
The transceiver remains the minimum volume level how-
ever the mechanical volume position is set to zero.
4-8. Call indicator
The call indicator can be programmed for each group. In
trunked system, it can be set to respond to a selectable de-
code ID or one of two fixed IDs, except block IDs. When a
call is received with a selectable decode ID, the call indicator
flashes. When a call is received with a fixed ID, the call indi-
cator lights continuously.
On a conventional system, the call indicator can be pro-
grammed to light for each QT or DQT code. It keeps flashing
while a call is being received. It is turned off by pressing any
front panel key.
4-9. Free system ringback
This feature is available only when a telephone intercon-
nected ID code is selected. If a busy tone sounds when the
PTT button is pressed, the transceiver enters this mode au-
tomatically.
When the PTT button is released, a beep sounds for
400ms to indicate that the mode has been entered. If the
scan is on, it is resumed (the "SCN" mark goes on). When
any repeater becomes available, a ringing tone sounds and
this mode ends.
The mode is terminated when the system, group, scan,
PTT, key is changed.
4-10. System search
This feature can be programmed to automatically access
other programmed systems when the selected system can-
not be accessed. If an intercept tone sounds when the PTT
button is pressed after setting the mode, the transceiver
has entered the mode.
If the group ID is a telephone interconnect ID, the trans-
ceiver then attempts to access, in succession, other sys-
tems that have a telephone interconnect ID in the revert
group location. If the group ID is a dispatch ID, the trans-
ceiver attempts to access other systems that have a dis-
patch ID programmed in the revert group location.
OPERATING FEATURES
sounds, the mode is terminated, and the transceiver returns
to the first system. If the access is successful, the mode is
terminated, and the searched system becomes the new se-
lected system (If during scanning, the scan stops).
4-11. Transpond
each group. If the ID of the group for which transpond is
enabled is received, two data messages (transmit ID and
turn-off code) are automatically transmitted if the PTT but-
ton is not pressed as a response within the time set (0 to
300 seconds in 1-second increments). If the PTT button is
pressed within the time, the transpond is not preformed.
4-12. Transmit inhibit
hibit block of ID codes. If an ID code within this block is de-
coded the preset time before the PTT button is pressed,
transmission is inhibited. The BUSY indicator lights and a
busy tone sounds until the PTT button is released to indicate
that transmission is not possible (except clear-to talk mode).
not set is inhibited, and the busy tone is output while the
PTT button is held down, regardless of the clear-to -talk set-
ting.
4-13. Auto TEL
pressing the key by assigning this feature to the key. This
feature accesses the TEL channel of the available system
automatically.
"AUTO TEL" appears on the alphanumeric display along
with a flashing handset indicator ( ) to indicate that this
mode has been entered. If the TEL ID is set for the revert
system, the TEL channel of that system is accessed. If all
TEL channels are busy, an attempt is made to access the
TEL channels of another system in which the TEL ID code
has been programmed. It is repeated for 60 seconds until
the access succeeds. If the access succeeds, a dial tone
returns from the repeater. If the key is pressed again when
the queue tone is sounding, this mode is canceled.
and this mode is terminated. When the talk ends, the revert
system/group returns. When the scan mode is effective, the
scan resumes. The Auto TEL feature can be programmed to
turn on or off for each system.
quest (ARQ) mode is a manner to minimize the air traffic of
data communication. Also, it enables to occupy the trunking
repeater channel for the data communication period.
a data transmission except for Selcall. A radio unit can re-
ceive a data message regardless of QT/DQT if the receiving
unit is not scanning.
TK-480/481
If there is no system to be accessed, an intercept tone
This feature can be programmed to turn on and off for
The transceiver can be programmed with a transmit in-
Transmission with the group for which the encode ID is
A telephone interconnect call can be made by simply
When the key is pressed, a queue tone is output, and the
If the access fails after 60 seconds, a deny tone is output
ARQ mode
If affects Trunking mode only. Automatic Repeat Re-
Data TX with QT/DQT
Whether programmed QT/DQT is modulated or not with
7