Table of Contents
Advertisement
S - 6 3 6
A. PERFORMANCE CONTROL SETTINGS
1. It is vital to match performance control settings to your level
of function and ability.
2. Consult your health care professional and your supplier to
select the best control settings for you.
3. Check and adjust the settings every six to twelve months (or
more often, if needed).
4. Adjust the control settings immediately if you notice any
change in your
ability to:
• Control the joystick.
• Hold your torso erect.
• Avoid running into objects.
5. Control Settings are adjusted through the use of the Qtronix
Programmer. See your supplier if you do not own a Qtronix
Programmer.
B. QTRONIX PROGRAMMING PAD
(OPTIONAL)
Program settings beyond the ability of the rider can
result in serious injury. Consult your health care advisor
before you alter settings.
1. Notes:
The Qtronix Programmer lets you adjust the performance control
settings of the S-636 SC / S-636 MPC. You can customize a program
for yourself or select the standard program.
• acceleration rate
• deceleration rate
• turn acceleration (tremor damping)
• turn deceleration (tremor damping)
• forward speed (max & min)
• reverse speed (max & min)
• turn speed (max & min)
• steer correct
• 4-axis joystick throw
• sleep timer
• number of profiles (1-5)
2. To Program Your Chair:
a. Turn off power to the chair.
b. Insert QTRONIX Programmer
plug (A) into the charg-
er/programmer socket on the
front of the joystick.
c. Turn on power to the chair; pro-
gram as needed.
d. Remove plug and cycle ON/OFF
switch to drive chair.
NOTE–
Review the Qtronix Programmer
Owner's Manual for more details
on how to program your chair.
NOTE–
Program settings that are not matched for the capabilities of the
rider can result in serious injury. Do not alter settings without the
advice of your health care professional.
108833 Rev. A
WARNING
C. THERMAL ROLL-BACK
Your chair has a thermal roll-back circuit. This protects the con-
troller from damage due to overheating. In extreme conditions
(such as repetitive hill climbing) the circuit will decrease the power
to your motors. This allows the chair to operate at a reduced
speed. When the controller cools, the chair will return to normal
speed.
D.CIRCUIT BREAKERS
1. Notes:
Your Quickie S-636 SC / S-636 MPC
has a battery box with a circuit
breaker.
• In the unlikely event of a short
circuit or heavy overload, all
power to your chair will be
shut off.
• To reset your chair, depress
the circuit breaker button (B)
on the front right side of the
battery box. A few minutes
wait is required before the circuit breaker will reset.
2. Repeated Shutdown:
If the chair continues to shut down after resetting, have it serviced
by a supplier.
E. JOYSTICK ASSEMBLY
The joystick connects to a controller, which controls the chair's
performance. The joystick assembly consists of the following parts:
1. Speed Control Knob (D):
Use the speed control knob to
adjust the maximum speed of your
chair. Turn it counter-clockwise to
reduce speed; turn it clockwise to
increase speed.
2 2 . . B B a a t t t t e e r r y y C C h h a a r r g g e e
I I n n d d i i c c a a t t o o r r ( ( B B ) ) : :
• Green lights indicate that bat-
teries are fully charged.
• Yellow lights indicate that bat-
teries need recharging.
• When the lights stay in the red band, the batteries must be
recharged.
3. On/Off Mode Switch (A)
A
The on/off mode switch is located on the rear face of the
joystick housing. It is a toggle switch. Turning the chair on or
off, is accomplished by pressing the switch downward. The
switch will automatically return to the center point. Alternate
locations exist for this switch. Please see your supplier in the
event that you wish to relocate or re-orient this switch.
4. Mode Switch (A)
The on/off mode switch allows you to select from 5 (five) different pro-
grammable drive profiles or actuator mode sets.
• Push up the on/off mode select toggle switch to index among
the five drive and actuator modes. The selected mode indica-
tor will flash.
18
X . O P E R AT I N G G U I D E
B
B
E
F
D
G
H
A
Remote Joystick
Advertisement
Table of Contents
