Subwoofer Output; Sound Field Control - Kenwood KDC-X990 Instruction Manual

General features

Subwoofer Output

Turning the Subwoofer output ON or OFF.
Hold down on [AM] of the Control knob for at
least 1 second.
Each time you push the knob, Subwoofer output
switches ON and OFF.
When it is ON, "SUBWOOFER ON" is displayed.
• You can control this function when "2ZONE" of
<Audio Setup> (page 11) is set to "OFF".
• You can control this item when Speaker Select
Subwoofer of <Sound Management system> (page
13) is set to any item other than "None".

Sound Field Control

1
Select the source to adjust
Press the [SRC] button.
2
Show the Multi-function display
Press the [NEXT] button repeatedly until
"S.F.C" appears.
Refer to <Notes on Multi-function System> (page
9).
3
Enter Sound Field Control mode
Turn the [VOL] knob to select "S.F.C".
Press the [VOL] knob.
• To get the best sound, first set the Cabin Setting
and Speaker Select Front/Rear parameters using the
<Sound Management system> (page 13).
• When "2ZONE" of <Audio Setup> (page 11) is ON, you
cannot select "S.F.C".
4
Select the Sound Field Control item to
adjust
1 Turn the [VOL] knob to select the item you
want to select. Press the [VOL] knob.
2 Press the Control knob.
3 Push the Control knob towards [FM] or
[AM].
12
|
English
1 2 3
"X'Over" "HPF Front" "fc"
"SLP"
"HPF Rear"*¹ "fc"
"SLP"
"LPF
"fc"
SubWoofer"*²
"SLP"
"Phase"
"DTA" "DTA Front"
"DTA Rear"*¹
"DTA
SubWoofer"*²
"POSI"
"Preset"
• "Preset": You can store an adjusted sound control
value by selecting "Memory". Refer to
<Memory mode> (page 16). Also, you
can recall it by selecting "Recall". Refer to
<Memory Recall mode> (page 16).
• You can adjust "SubWoofer" when <Subwoofer
Output> (page 12) is set to "SUBWOOFER ON".
• X'Over (Crossover Network Setup)
You can manually set a crossover frequency for the
speakers.
• DTA (Digital Time Alignment)
Manually set the sound output timing of each
channel.
• * 1 You can control this item when Speaker Select Rear
of <Sound Management system> (page 13) is set to
any item other than "None".
• * 2 You can control this item when Speaker Select
Subwoofer of <Sound Management system> (page
13) is set to any item other than "None".
5
Adjust the Sound Field Control item
Push the Control knob towards [4] or
[¢].
Each time you push the knob, the setting
alternates between the settings shown in the
table below.
Sound Field Control Item
Front High Pass Filter Frequency/
Rear High Pass Filter Frequency
Front High Pass Filter Slope/
Rear High Pass Filter Slope/
Subwoofer Low Pass Filter Slope
Subwoofer Low Pass Filter Frequency
Subwoofer Low Pass Filter Phase
Sound Field control item
Front High Pass Filter Frequency
Front High Pass Filter Slope
Rear High Pass Filter Frequency
Rear High Pass Filter Slope
Subwoofer Low Pass Filter Frequency
Subwoofer Low Pass Filter Slope
Subwoofer Low Pass Filter Phase
DTA Front
DTA Rear
DTA Subwoofer
Position Setting
Preset value storage/recalling
Range
Through/30 — 100/120/150/
180/220/250 (Hz)
-12/-18/-24 dB/Oct
30 — 100/120/150/180/220/
250 (Hz)/Through
Normal/ Reverse