Quick Reference - Sharp Aquos LC-42D~43U Operation Manual

QUICK REFERENCE
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the 1V on. This will prevent it from being damaged.
~
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
@·7
CD
Insert the stand into the openings on the
bottom of the TV.
®
Insert and tighten the 4 long screws into
the 4 holes on the rear of the TV.
Hexkey-®~
I
BJmm
• To detach the stand, perform the steps in reverse order.
BJmm
• To detach the stand, perform the steps in reverse order.
~~ii ,~,~
CD
Set the post for the stand unit onto the box.
®
Attach the base to the post.
@
Insert and tighten the 4 short screws into
the 4 holes on the bottom of the base.
Attach the two supporting posts for the stand
unit onto the base using the box for the stand
unit as shown below.
(Close-up of the upper side of the stand unit)
• LC-46D43U1LC-52D43U
Confirm that there are 10 screws (6 short
screws and 4 long screws) supplied with the 1V.
//_::=-..
a
~
%@J
?' /.'
"'.-®.~.,I~
. / ..
?~~~~
~,,~~~p
'-/'''~
t
t . ~'PJ
Hex key
Short screw
r
1 Insert each of the protrusions on the two
supporting posts into the openings on the
upper side of the base.
2 Insert and tighten the 6 short screws with
the hex key (supplied with the product) in the
order of
CD, ®
and
@ .
• LC-42D43U
Confirm that there are 8 screws (4 short screws
and 4 long screws) supplied with the TV.
QUICK REFERENCE
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the 1V on. This will prevent it from being damaged.
~
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
@·7
CD
Insert the stand into the openings on the
bottom of the TV.
®
Insert and tighten the 4 long screws into
the 4 holes on the rear of the TV.
Hexkey-®~
I
BJmm
• To detach the stand, perform the steps in reverse order.
BJmm
• To detach the stand, perform the steps in reverse order.
~~ii ,~,~
CD
Set the post for the stand unit onto the box.
®
Attach the base to the post.
@
Insert and tighten the 4 short screws into
the 4 holes on the bottom of the base.
Attach the two supporting posts for the stand
unit onto the base using the box for the stand
unit as shown below.
(Close-up of the upper side of the stand unit)
• LC-46D43U1LC-52D43U
Confirm that there are 10 screws (6 short
screws and 4 long screws) supplied with the 1V.
//_::=-..
a
~
%@J
?' /.'
"'.-®.~.,I~
. / ..
?~~~~
~,,~~~p
'-/'''~
t
t . ~'PJ
Hex key
Short screw
r
1 Insert each of the protrusions on the two
supporting posts into the openings on the
upper side of the base.
2 Insert and tighten the 6 short screws with
the hex key (supplied with the product) in the
order of
CD, ®
and
@ .
• LC-42D43U
Confirm that there are 8 screws (4 short screws
and 4 long screws) supplied with the TV.