U-Line H-1027 User Manual

Pneumatic stick stapler

Advertisement

Quick Links

H-1027, H-1028
H-3064
pneUMatIc stIcK
stapler
PAGE 1 OF 11
Before operating this stapler familiarize yourself with the safety
warnings and instructions in this manual. Keep these instructions with
the stapler for future reference. If you have any questions, contact
Uline at 1-800-295-5510.
stapler specIfIcatIons
Dimensions: L x H x W
Weight (Without Fasteners)
Compressed Air:
Maximum psi:
Recommended
Operating Pressure:
Air Consumption:
Staple Specification:
Staple Specification:
Staple Specification:
Staple Capacity:
Noise Levels:
warnIng
13.5 x 8.75 x 6"
6 lb.
110 psi
71–100 psi
2.4 CFM
S-1397 A58 Stick
S-1396 C34 Stick
S-289 C58 Stick
100 Staples
89 dBa
0513 IH-1027

Advertisement

Table of Contents
loading

Summary of Contents for U-Line H-1027

  • Page 1 H-1027, H-1028 H-3064 pneUMatIc stIcK stapler stapler specIfIcatIons Dimensions: L x H x W 13.5 x 8.75 x 6" Weight (Without Fasteners) 6 lb. Compressed Air: Maximum psi: 110 psi Recommended Operating Pressure: 71–100 psi Air Consumption: 2.4 CFM Staple Specification:...
  • Page 2: General Safety

    safety InstrUctIons general safety lUBrIcatIon & MaIntenance 1. Read the manual and understand all safety 1. Lubricate the stapler prior to initial operation. instructions before operating the stapler. If you have 2. Disconnect the stapler from the air supply prior to questions, contact Uline at 1-800-295-5510.
  • Page 3: Loading The Stapler

    safety InstrUctIons contInUed loadIng tHe stapler 4. Pull the pusher back to an upright position and 1. Disconnect the air supply. gently let the pusher slide forward against the 2. Pull the pusher back until it stops on pusher pivots. staples.
  • Page 4: Clinch Adjustment

    safety InstrUctIons contInUed clIncH adjUstMent Use 2.5 mm Allen wrench and turn collar through window clockwise to tighten clinch. (See Figure 6) Loosen Tight Medium Tighten Loose Figure 6 deptH adjUstMent 3. When the top edge of the adjustment plate is at 1.
  • Page 5: Cleaning The Stapler

    operatIng InstrUctIons warnIng 1. protect your eyes and ears. wear safety glasses with side shields wear hearing protection. ensure that anyone in the vicinity wears safety protection. 2. to prevent accidental injuries, never place a hand or any other body part in the staple clinching area or adjustment window.
  • Page 6: Clearing A Jam

    operatIng InstrUctIons contInUed clearIng a jaM 3. Insert needle nose pliers or screwdriver to clear jam. 1. Disconnect air supply. (See Figure 12) 2. Pull pusher back and rotate to a locked position. 4. Slowly release pusher back to position. (See Figure 11) Figure 11 Figure 12...
  • Page 7: Teeth Replacement

    operatIng InstrUctIons contInUed teetH replaceMent 3. Loosen screws with 3 mm Allen wrench. 1. Loosen screws and nut with an 8 mm wrench and (See Figure 15) 4 mm Allen wrench. (See Figure 13) 4. Change teeth one at a time to prevent reverse 2.
  • Page 8: Driver Replacement

    operatIng InstrUctIons contInUed drIVer replaceMent 5. Slide the linkage mechanism and adjusting rod 1. Disconnect the air supply. simultaneously from the collar. (See Figure 18) 2. Loosen screw and nut with a 8 mm spanner wrench 6. Loosen the screws with a 3 mm Allen wrench. and a 4 mm Allen wrench.
  • Page 9 operatIng InstrUctIons contInUed pUsHer sprIng replaceMent 5. Loosen the screw and nut with a 2.5 mm Allen 1. Loosen the screws and nut with a 8 mm spanner wrench and 7 mm socket wrench. (See Figure 24) wrench and a 4 mm Allen wrench. (See Figure 21) 6.
  • Page 10: Valve And Tube O-Ring Replacement

    operatIng InstrUctIons contInUed ValVe and tUBe o-rIng replaceMent 3. Remove C-ring with C-ring pliers. 1. Loosen screws with a flat screwdriver. (See Figure 27) (See Figure 29) 2. Remove spring with needle nose pliers. 4. Remove valve and tube with needle nose pliers. (See Figure 28) (See Figure 30) Figure 27...
  • Page 11: Piston Replacement

    operatIng InstrUctIons contInUed pIston replaceMent 6. Loosen screw with a 3 mm Allen wrench and remove 1. Remove screws and nut with 8 mm spanner wrench the block through the window. and 4 mm Allen wrench. (See Figure 31) 7. Loosen screws with a 3 mm Allen wrench and 2.

This manual is also suitable for:

H-1028H-3064

Table of Contents