CONGRATULATIONS on your purchase of a Viper product, and welcome to the V.I.P. family. We appreciate your business and will do every- thing in our power to keep you happy with your purchase for many years to come. As part of the V.I.P. family, you are entitled to the best protection by one of the most comprehensive warranties in the industry.
SAFETY PRECAUTIONS WHEN SERVICING MACHINE: (con’t) x Disconnect batteries prior to working This machine is intended for commercial use. It is on machine. constructed for use in an indoor environment and x Wear gloves when handling batteries is not intended for any other use. Use only with or battery cables.
R E D B L A C K FILLING THE SOLUTION TANK 1. The Fang 24T / 26T / 28T can be filled in two B A T T E R Y B R A C E different locations: C H A R G E R P L U G a.
10. This machine has reverse. In order to activate reverse, there is a toggle switch located on the : If you are filling the solution tank with a left side of the control housing. (see machine bucket, make sure the bucket is clean. This will components, item #18) The toggle switch prevent debris from clogging the lines or solenoid.
DRAINING THE SOLUTION (CLEAN) TANK : The brush motors are circuit breaker : Anytime scrubbing operation is completed, protected to protect them from damage. If a the solution tank should be drained and cleaned. breaker trips, it can’t be reset immediately. You 1.
DAILY MAINTENANCE to overflow during charging due to expansion. Replace the caps prior to charging. 1. Remove pad driver / brush and clean with 5. Plug approved charger into grounded wall approved cleaner. outlet before plugging the charger into the 2.
1. Contact your local Viper Distributor for any caused by freezing temperatures will not be motor maintenance. covered by the warranty. 2. Vacuum motor should have the brushes 7. Drain the recovery tank and remove the clear checked every 250 hours. Brushes should be...
Tighten loose cable(s) Batteries not connected properly Follow battery installation instructions Brush motor does Bad brush switch Contact Viper Distributor not run Brush circuit breaker has tripped Check brush motor for obstructions and reset breaker Rectifier has burned out Contact Viper Distributor...
Page 12
FANG 24T,FANG 26T & FANG 28T - SOLUTION TANK ASSEMBLY PART DESCRIPTION NUMBER REQ'D VF81405BD GRIP,HANDLE VA13477 SCREW, SELF-TAPPING, ST, M4 X 16 VV13664 WASHER,PLAIN, M4 X M12 X 1 VV13604 SCREW, M8 X 20 VF13519 WASHER,LOCK, M5 X M11 X 28...
Page 13
FANG 24T,FANG 26T & FANG 28T - SOLUTION TANK ASSEMBLY PART DESCRIPTION NUMBER REQ'D VF81724 CAPS,BATTERY,BLACK VF81724R CAPS,BATTERY,RED CHRGR18 CHARGER,24V,18AMP VF13537 WASHER,PLAIN, M10 X M26 X 2 VF13518 WASHER,LOCK, M10 VF14234 SCREW, M8 X 16 VF13513 NUT, M8 VF81408 PLATE,LOCK...
Page 15
FANG 24T, FANG 26T & FANG 28T - RECOVERY TANK ASSEMBLY PART DESCRIPTION NUMBER REQ'D VF82010 CLEAR COVER,RECOVERY TANK VF82083 DECAL WARNING BATTERY VF82009 ELBOW ADAPTOR,FLOAT VV13607 WASHER,LOCK, M6 VF13533 WASHER,PLAIN, M6 X M16 X 2 VF14233 SCREW, M6 X 20...
Page 17
FANG 24T, FANG 26T & FANG 28T - BRUSH LIFT/DRIVE ASSEMBLY PART DESCRIPTION NUMBER REQ'D VF82080 HUB CAP VF81106 WHEEL, 8" VF81600 TRANSAXLE, 24" ZD72000A TRANSAXLE MOTOR, 24VDC VF81102 BRACKET,TRANSAXLE MOUNT VF13537 WASHER,PLAIN, M10 X M26 X 2 VF13518 WASHER,LOCK, M10...
Page 19
FANG 24T,FANG 26T & FANG 28T - BRUSH/PAD DRIVE ASSEMBLY PART DESCRIPTION NUMBER REQ'D VF83112A BLOCK,GUIDE VV20274B WASHER,PLAIN, M13 X M39 X 2 VA13400 WASHER,PLAIN, M5 X M11 X 1 GT13022 NUT,LOCK, M5 VF14234 SCREW, M8 X 16 VF13519 WASHER,LOCK,M8...
Page 21
FANG 24T, FANG 26T & FANG 28T - SOLUTION CONTROL ASSEMBLY PART DESCRIPTION NUMBER REQ'D VF14245 SCREW, M5 X 6 VF82036 SHAFT VV13650 SCREW, M4 X 10 VF13532 WASHER,PLAIN, M5 VV13601 WASHER,LOCK, M5 VF14230 SCREW, M5 X 15 VF13536 WASHER,PLAIN, M9.8 X M16 X 1 VF82075 NUT, 3/8"...