Advertisement
CONNECTING THE LP TANK
WARNING! ALL OF THE INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE
MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY!
WARNING!
1.
The knob on the LP tank must be closed. See that the knob is turned clockwise to a full stop.
2.
Check that the Control Knob on the Smoker is turned off.
3.
Remove the protective cap from the LP tank valve and coupling nut, if present.
4.
Hold the regulator in one hand and insert the nipple into the valve outlet. Be sure the nipple
is centered in the valve outlet. The coupling nut connects to the large outside threads on the valve
outlet. Use care – do not cross-thread the connection.
5.
Hand tighten the coupling nut clockwise until it comes to a full stop. Firmly tighten by hand
only. DO NOT use tools.
CAUTION: In the gas connection process, when threading the HVP Hose to the LP tank valve
some resistance will be encountered. This is normal when seating the valve. Seating the valve
requires about one-half to three-quarters additional turns to complete the connection.
.
Any fuel supply cylinder used must be constructed and marked in accordance with
specifications for propane cylinders of the U.S. Department of Transportation (DOT) CFR 49,
or CAN/CSA B339. The appliance is to be used only with the 20 pound, vertical
standing vapor withdrawal type tank.
(A) Do not store tanks under or near the Smoker.
(B) Never fill tanks more than 80% full.
If instruction A and B above are not followed exactly, a fire causing death or serious injury may occur.
.
This Smoker is designed to operate on LP (Liquefied Propane) gas only.
.
The 20 lb LP cylinder used with this Smoker must conform to the following requirements: Diameter- 12" (30.5cm), Height- 18"
(45.7cm), with a Maximum Capacity of 20 pounds.
.
The gas cylinder used must include a collar to protect the cylinder valve. The cylinder supply system must be arranged for vapor
withdrawal.
.
The instructions stated on gas cylinder tanks have to be followed when filling or transporting tanks. Failure to do so could
result in problems relating to overfilling, excessive venting release of gas and to regulator freezing.
.
Do not allow dirt or foreign material to get into or onto tank connection when it is not attached to the fuel supply system. Use the
protective cap provided.
Cylinders must be filled before initial use. All handling, transport, filling and storage of LP gas cylinders must be in accordance with NFPA 58
Storage and Handling of Liquid Petroleum Gases, or CAN/CGA B149.2 Propane Installation Code. Cylinders must be suitably tied down during
transport. Do not place any other items on top of cylinders at any time. Cylinders are not to be exposed to excessive temperatures or high heat.
If there is a question on the identity of your unit and of the type of fuel to be used, please look on the data plate. Units are factory equipped
for use on only one type of fuel. These units cannot be, and should not be used on other type of fuels. Doing so can cause severe damage
to the unit and the installation area and the added risk of serious injury. Any attempt to operate these smokers on fuels for which they
are not design certified voids the manufacturer's warranty.
Gas tank outlet must have Type 1 gas connection terminal in order to mate with gas hose provided with Smoker.
The pressure regulator and hose assembly supplied by the manufacturer with the appliance must be used. Replacement pressure regulators
and hose assemblies must be those specified by the appliance manufacturer.
The regulator/hose assembly should be handled carefully to prevent contamination by foreign objects and dirt. The assembly should be
inspected before use and any dirt or contamination should be wiped off. In order to insure proper operation, any replacement of the fuel tank
regulator assembly has to be done with parts authorized by the smoker manufacturer.
This unit is not to be utilized with a non-self-contained LP-gas supply system.
WARNING: Valve/pressure regulators are factory set to the correct operating pressures. No attempts should be
made to adjust these settings!
-12-
LOCATE THESE PARTS
LOCATE THESE PARTS
FIGURE 21
2 CARRY
HANDLES
HARDWARE
HARDWARE
8 NUTS
8 LOCK WASHERS
1.
Line up the Carry Handle with the corresponding holes on the side
of the Cabinet. The Handles must be positioned upright with the
bolt holes on the bottom.
2.
Insert the Bolts from the outside and thread the Lock Washers and
Nuts from the inside of the Cabinet. Firmly tighten the Nuts.
3.
Complete steps for both sides of the Cabinet Assembly and Carry
Handles.
LOCATE THESE PARTS
WOOD CHIP BOX
& WOOD CHIP LID
1.
Position the Wood Chip Box Stand on top of the Burner
Chamber, resting in the two notches of the Stand.
2.
Set the Wood Chip Box on top of the Wood Chip Box Stand.
3.
Place the Wood Chip Box Lid on top of the Wood Chip Box.
Figure 13
ASSEMBLY STEP 6
SECURING THE HANDLES
TOOLS NEEDED
TOOLS NEEDED
PHILLIPS
HEAD
SCREWDRIVER
C
HARDWARE BAG
1/2" WRENCH
8 BOLTS
NUTS
LOCK
Figure 12
WASHERS
CABINET
ASSEMBLY
ASSEMBLY STEP 7
WOOD CHIP BOX INSTALLATION
WOOD CHIP BOX
STAND
WOOD CHIP BOX
& WOOD CHIP LID
WOOD CHIP
BOX STAND
BURNER
CHAMBER
-9-
CARRY
HANDLES
BOLTS
FIGURE 12
FIGURE 13
Advertisement
