Advertisement
OPERATING INSTRUCTIONS
SEASONING YOUR SMOKER
Before you cook food in your Smoker, it is important to "season" your Smoker. Seasoning seals the paint and interior of your Smoker to
enhance flavoring, durability, and overall performance. This is also referred to as the "break -in" Process.
.
To season your Smoker, simply use it as you normally would, only do not cook any food. You will need to follow all of the operating
procedures in the next few sections of this manual.
.
Using your desired flavoring woods and marinades, burn your Smoker at low temperature (around 175°F) for 45-60 Minutes. Let the
Smoker cool, and clean out the used water and wood.
.
Once the seasoning is complete, your Smoker's interior will have a durable, seasoned coating.
ADDING WATER TO YOUR SMOKER
.
To add water BEFORE cooking, simply remove the Water Bowl and fill it with heated water up to 1" below the rim. Then replace the
Water Bowl to the bottom of the Rack.
.
To add water WHILE the Smoker is hot, DO NOT pull the Water Bowl out beyond the Rack! The water and the Water Bowl will be
extremely HOT!
.
To make adding water easier and safer, use a clean watering can or jug with a long spout.
.
Line the Water Bowl with aluminum foil before each use. This will make it easier to clean and extend the life of the Water Bowl.
ADDING WOOD/CHARCOAL TO YOUR SMOKER
.
To add wood chips BEFORE cooking, simply fill the Wood Chip Box with your choice of flavoring hardwood chips. The amount and
type of wood you use is entirely up to you. One full box is typically enough for several hours of smoking. Once the Wood Chip Box
is filled, place the Wood Chip Box Lid on top of the Wood Chip Box and set the Wood Chip Box in the Smoker.
.
To add wood chips WHILE cooking, we recommend using tongs or long handled pliers to remove the Wood Chip Box Lid and to
place the pieces into the Wood Chip Box without removing it. IT IS NOT RECOMMENDED to remove the Wood Chip Box while
the Smoker is in operation.
CAUTION: The Wood Chip Box and the Wood Chip Box Lid get very HOT! Avoid handling them while in use. ALWAYS wear
protective oven mitts when handling hot components!
WOOD FLAVOR CHOICES FOR YOUR SMOKER
Small wood chips work best inside the Wood Chip Box. Use dry hardwoods such as hickory, pecan, apple, cherry, or mesquite. Most
fruit or nut tree woods produce excellent smoke flavoring. Do not use resinous woods such as pine or plywood. These usually produce
unpleasant flavoring. Let your taste be your guide – experiment with different types and quantities of wood chunks, chips, or sticks. You
can even mix woods.
To produce more smoke and to prevent fast burning, pre-soak the wood chips in a separate bowl of water for at least 20 minutes, or wrap
the chips in perforated aluminum foil. Most smoke flavoring occurs within the first hour of cooking. Adding wood chips after the first hour is
typically not necessary unless extra smoke flavoring is desired.
NOTE: To catch drippings that may come from the bottom of the Smoker, place a metal tray underneath.
-14-
ASSEMBLY STEP 3
CONTROL PANEL / HVR SYSTEM / IGNITOR INSTALLATION
LOCATE THESE PARTS
CONTROL
PANEL
ASSEMBLY
IGNITOR
KNOB
ASSEMBLY
CONTROL
KNOB
HARDWARE
HARDWARE BAG
NOTE: Hardware Bag
A includes 12 Bolts.
You will need 2 bolts
2 BOLTS
for this step. The other
10 bolts were used in
Step 2.
1.
Leave the Cabinet positioned upside down.
2.
Attach the Ignitor Knob and the Control Knob to the Control
Panel Assembly.
Make sure the Control Knob
FIGURE 5
properly seats on the keyed shaft.
FIGURE 6
3.
Line up the Control Panel.
FIGURE 7
4.
The (Hose/Valve/Regulator) HVR stem must be inserted into
WARNING! Improper installation may
the Venturi.
FIGURE 8
cause a fire outside of the Smoker!
5.
When sliding the Control Panel into place, make sure the tabs
capture the front Legs.
FIGURE 9
6.
Connect the Ignitor wire to one of the prongs on the Ignitor.
FIGURE 9
7.
Insert the 2 remaining Bolts from Hardware Bag A through the
tabs on the Control Panel and thread them into the mounting
holes.
FIGURE 8
8.
Firmly tighten all of the Bolts, including the loose Bolts
on the front Legs.
REMAINING
Be sure the tab fits
BOLT
around both sides
of the LEG.
HVR STEM
inserted into the
VENTURI.
FIGURE 8
TOOLS NEEDED
Tools needed:
HVR
PHILLIPS
HEAD
SCREWDRIVER
A
CONTROL
PANEL
ASSEMBLY
IGNITOR
KNOB
VENTURI
HOSE
IGNITOR WIRE
connects to
the IGNITOR.
FIGURE 9
FRONT
TOP
-7-
FIGURE 5
CONTROL
KNOB
FIGURE 6
FIGURE 7
Advertisement
