Home Position Adjustment - Casio 5011 (W3) Operation Manual

Home Position Adjustment

If the time setting of your watch is not correct even though
time calibration signal reception is being performed normally,
use the procedure in this section to check the home positions
of the hands and make adjustments as required.
Note that you do not need to perform the following operation if
your watch is showing the correct time.
1.
Indicator hand
In the Timekeeping Mode,
hold down the A A A button A A
and then the C C C C C button for
about three seconds.
• The watch will beep, and then
the indicator hand and the
second hand will move their
home positions.
30
Home Positions
Second hand
Indicator Hand: 12 o'clock
Second hand: 0 (60 on some
models)
7.
C C button. C
Press the C C
• This causes the day to move
to its home position.
Home Position
Day: 1 1
Day
• If the day hand is at its proper home position, advance to step 9.
If the day is not at its proper home position
8.
Use the D D (+) and B D D D B B B B
(–) buttons to adjust
the day.
• Holding down either
button will cause the
hands to move at high
speed. Once started,
high-speed hand
1
movement will continue
even if you release the
button. To stop high-
speed hand movement,
press any button.
Operation Guide 5011 (W3)
• If the indicator hand and second hand are both at their proper
home positions, advance to step 3.
• The watch will return to normal timekeeping automatically if you
do not perform any operation for about two or three minutes. Any
changes you have made to settings up to that point will be saved.
If the indicator hand or second hand is not at
its proper home position
2.
Adjust the applicable
hand to its home
position.
• Use the B button to
adjust the indicator
hand.
• Use the D button to
adjust the second hand.
• The hands move
clockwise only. Keep
pressing a button until
the applicable hand is at
its proper home position.
9.
A A button to exit A
Press the A A
home position adjustment
and return to normal
timekeeping.
• If you press the C button
instead of the A button, the
watch will return to step 1
(indicator hand and second
hand home position
adjustment) of this procedure.
After completing home position adjustment, place the watch in
a location where signal reception is good and perform Manual
Receive.
• For details about the manual receive procedure, see
"Manual Receive".
(–)
(+)
3.
Press the C C C C C button.
• This will cause the hour hand,
minute hand, and 24-hour
hand to move to their home
positions.
Home Positions
Hour hand: 12 o'clock
Minute hand: 12 o'clock
24-hour hand: 24:00
• If the hour, minute, and 24-nour hands all are at their proper home
(Indicator hand)
positions, advance to step 5.
If the hour and minute hands are not at their
proper home positions
4.
Use the D D D D D (+) and B
(–) buttons to adjust
the hand positions.
30
• Holding down either
(Second hand)
button will cause the
hands to move at high
speed. Once started,
high-speed hand
movement will continue
even if you release the
button. To stop high-
speed hand movement,
press any button.
• The 24-hour hand is synchronized with the hour and
minute hands, so separate adjustment is not required.
30
Minute hand 5.
Press the C
24-hour hand Hour hand
• This causes the day of the
week hand to move to its
home position.
Home Position
Day of the week hand: 60
30
• If the day of the week hand is at its proper home position,
advance to step 7.
If the day of the week hand is not at its proper
home position
6.
Use the D
B B B B
(–) (–) buttons to adjust
the day of the week
hand.
• Holding down either
button will cause the
hand to move at high
30
speed. Once started,
(+)
high-speed hand
movement will continue
even if you release the
button. To stop high-
speed hand movement,
press any button.
Day of the week hand
C C button. C C
30
D (+) and B D D D B B B B
(–)
30
(+)
9