Table of Contents
Advertisement
Configuring Home City Settings
Use the procedures in this section to configure Home City settings,
including selecting a region and city code, setting the time and date,
etc. You also can use the procedures in this section to adjust the
time and date when the watch is unable to receive a time calibration
signal for some reason.
• Always use the Timekeeping Mode to configure and adjust Home
Time settings.
• Each press of the C button cycles through available settings in
the sequence shown below.
• Home City
Hour and minute
• Summer time
Day
4.
A
A
A
When everything is the way you want, press the A
A
button.
• This will apply your settings and return to normal timekeeping.
The second hand will move to and start timekeeping from the
appropriate seconds count in accordance with the watch's
internal timekeeping.
I To adjust the current time and date
setting manually
1.
In the Timekeeping Mode,
keep the A
A
A
A
A button
depressed (for about five
seconds) as the indicator
hand goes through the
following sequence.
• The indicator hand will move
30
to the last signal reception
result ("Y" or "N"), then to
Second hand
"READY" (or "R" for some
models), and then the city
Indicator hand
code of the currently selected
Home City.
• At this time the second hand will move to "0" ("60" for some
models).
• The watch will return to normal timekeeping automatically if
you do not perform any operation for about two or three
minutes. Any changes you have made to settings up to that
point will be saved.
Operation Guide 5011 (W3)
I To select your Home City and change its
summer time setting
1.
In the Timekeeping Mode,
A
A button
A
keep the A
A
depressed (for about five
seconds) as the indicator
hand goes through the
following sequence.
• The indicator hand will move
Year
to the last signal reception
result ("Y" or "N"), then to
Second hand
"READY" (or "R" for some
models), and then the city
code of the currently selected
Home City. Next, the second
Month
hand will move to "0" ("60" for
some models).
• The watch will return to normal timekeeping automatically if
you do not perform any operation for about two or three
minutes. Any changes you have made to settings up to that
point will be saved.
2.
C
C
C button.
Press the C
C
• The indicator hand will move
to 12 o'clock, and the day of
the week hand will move to
"0" ("60" for some models).
3.
24-hour hand
Use the D
D
D (+) and B
D
D
B
B
B
B (–)
buttons to change the
time setting in one-minute
increments.
• Holding down either button
will cause the hands to move
at high speed. Once started,
high-speed hand movement
will continue even if you
release the button. To stop
high-speed hand movement,
press any button.
• Check the 24-hour hand to make sure that the time is set
properly (1:00 a.m. = 1 o'clock, 1:00 p.m. = 13 o'clock).
2.
Press the D
D
D
D button to
D
move the indicator hand
clockwise.
3.
Press the B
B
B
B
B button to
cycle through the summer
30
time (DST) settings
described below.
Indicator hand
4.
C
C
C to change to the
Press C
C
year setting.
30
(–)
5.
Use the D
D
D
D button to move
D
the units digit hand
clockwise and the B
B
B
B
B
button to move the tens
digit hand clockwise.
30
(+)
20X9
20X8
20X7
20X6
• • • • • AT (AUTO)
This setting enables the auto summer time setting, which
turns summer time on or off in accordance with the received
time calibration signal.
This is the factory default setting for the following city codes:
LON, PAR, ATH, TYO, ANC, LAX, DEN, CHI, NYC.
• This setting is available for the following city codes only:
30
LON, PAR, ATH, HKG, TYO, HNL, ANC, LAX, DEN, CHI,
(+)
NYC.
• • • • • ON
This setting turns on summer time and advances the current
time by one hour from standard time.
• • • • • OFF
This setting turns off summer time and displays standard time.
• Signal reception is possible in the time zones represented by
HKG (Hong Kong), HNL (Honolulu), and ANC (Anchorage) when
reception conditions are good.
30
• If you want to proceed with adjusting the current time and date
setting, continue from step 2 under "To adjust the current time and
date setting manually."
• Use the B button to move the tens digit (indicator) hand
Tens digit
clockwise.
30
20X9
Units digit
20X8
6.
C
C
Press C
C to change to the
C
month setting.
30
20X0
20X1
20X2
20X3
20X4
20X5
200X
20X1
20X2
20X3
20X4
20X7
20X5
20X6
30
Moves to the current
month setting.
7
Advertisement
Table of Contents
