Kenwood TK-3230 Service Manual page 5

3-3. Operation
1. To switch the clone target/s to Clone mode, press
and hold the [PTT] and [MONI] keys while turning the
transceiver power ON.
2. Keep holding [PTT] and [MONI] keys for 1 second.
Transceiver sound key on tone and enters Clone mode
with " " display.
3. Wait for 2 seconds. Transceiver displays "
4. Select a channel table number using [UP] (increment
channel table) and [DOWN] (decrement channel table)
keys.
5. To switch the clone source to Clone mode, press
and hold the [PTT] and [MONI] keys while turning the
transceiver power ON.
6. Keep holding [PTT] and [MONI] keys for 1 second.
Transceiver sound key on tone and enters Clone mode
with " " display.
7. Wait for 2 seconds. Transceiver displays "
8. Select the same channel table number as the clone
target/s.
9. P r e s s [ P T T ] o n t h e c l o n e s o u r c e t o b e g i n d a t a
transmission. When the clone target starts to receive
data, the LED will light green.
When the clone source finishes sending data, a
"confi rmation" tone will sound with "
If data transmission fails while cloning, an "error" tone
will sound from the Target unit with "
10. If the cloning fails, no data will be available in the Target
unit when it is returned to User mode.
11. When the cloning is successful, the Target unit's "Scan",
"Key Lock" and "Super Lock" functions will return to
their default values (Scan = OFF, Key Lock = OFF, Super
Lock = OFF).
12. After clone has completed, it is necessary for the Target
unit to set its required ID Type of ID List for FleetSync.
This can be done by using unit's ID List Setting Mode.
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceiver's Clone Mode is configured as
"Disabled", the transceiver cannot enter Clone mode.
• The table shown below will cover the frequencies used
for wireless cloning.
• A unit cannot be a "Source Unit" if it is unprogrammed.
If [PTT] is pressed, an "error" tone will sound.
• Once a unit is set to be the Source, it cannot be a target
after the data has been transmitted. This protects the
data in the Source unit.
• If the Target unit is cloned unsuccessfully, "error" tone
will sound with "
" display.
• After 4 seconds, Target unit returns to display "
"xx" means the last selected channel table number.
• The Source unit and Target unit must be of the same
model type and destination in order for Clone to operate.
• It is not possible to read/write setup data from the clone
source/target when it is in Clone mode. But it will trigger
to go to cloning mode (TX) when try to read/write.
REALIGNMENT
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be confi gured as "Disable"
before being delivered to the end-user.
• When wireless Clone mode is used, the environment
".
must ensure that the radio wave does not leak to
outside.
• The transmit output power is automatically set to Low in
Clone mode.
• Battery saver function is automatically set to off in Clone
mode.
Channel
setup No.
".
01
02
03
04
05
" displayed.
06
07
" displayed.
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
".
27
28
User can select channel frequency from above.
TK-3230
Channel
Frequency (MHz)
setup No.
464.50000 29
464.55000 30
467.76250 31
467.81250 32
467.85000 33
467.87500 34
467.90000 35
467.92500 36
461.03750 37
461.06250 38
461.08750 39
461.11250 40
461.13750 41
461.16250 42
461.18750 43
461.21250 44
461.23750 45
461.26250 46
461.28750 47
461.31250 48
461.33750 49
461.36250 50
462.76250 51
462.78750 52
462.81250 53
462.83750 54
462.86250 55
462.88750 56
Table 1 Cloning frequency table
Frequency (MHz)
462.91250
464.48750
464.51250
464.53750
464.56250
466.03750
466.06250
466.08750
466.11250
466.13750
466.16250
466.18750
466.21250
466.23750
466.26250
466.28750
466.31250
466.33750
466.36250
467.78750
467.83750
467.86250
467.88750
467.91250
469.48750
469.51250
469.53750
469.56250
5