Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for VarTech Systems VT420 Series
Summary of Contents for VarTech Systems VT420 Series
-
Page 1: Lcd Monitor
LCD monitor Model: SERIES VT420 Series www.vartechsystems.com... -
Page 2: Table Of Contents
The Side Controller Of The Monitor .......................14 The Remote Control (RCU ) Instructions....................16 Change The RCU Battery ........................17 Display Mode............................18 On-Screen Display (OSD)........................25 Default Setting ..............................34 Touch Operation ..............................35 Supported Timing.............................36 Specification ..............................37 Troubleshooting ...............................38 Compliance ..............................38 Appendix I...............................39 Appendix II..............................40 Appendix III..............................42 VT420 Series www.vartechsystems.com... -
Page 3: Important Safety Instructions
When turning off the monitor by pressing the POWER button on the remote control, the main power of the monitor is not turned off completely. To disconnect the monitor completely from power supply, remove the power plug from the outlet. Press”O”to turn off monitor completely VT420 Series www.vartechsystems.com... -
Page 4: Installation (When Install The Monitor, Please Follow The Instruction On The Manual)
When unpacking or carrying the monitor, at least 2 people are needed. Make sure the monitor is carried upright. Transport the monitor upright. Avoid placing the monitor face up or down. Handle the monitor gently. Do not drop. VT420 Series www.vartechsystems.com... -
Page 5: Use
If the glass of the monitor panel is broken, liquid may escape. Please don't touch the liquid. If liquid get into your eyes or touches your skin, wash with the clean water and seek medical attention immediately. VT420 Series www.vartechsystems.com... -
Page 6: Clean
This product isn’t warranted for any damage caused by neglect of the instructions described about installation. This product isn’t warranted for any damage caused by improper installation. This product isn’t warranted for any damage caused by disassembly, modification or repair by non-authorized service center or people. VT420 Series www.vartechsystems.com... -
Page 7: Features
Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet. Set the LCD Monitor box in an upright position and open from the top of the box before removing the top cushions. Step 1: Remove the white handle and cut the banding VT420 Series www.vartechsystems.com... - Page 8 3 Bottom cushion 1 pcs 4 Top cushion 1 pcs 5 Packing bag 1 pcs Accessories Bag Remote control 1 pcs Batteries 2 pcs Power cord 1 pcs D-SUB 15pin cable 1 pcs 7 Carton lock 4 pcs VT420 Series www.vartechsystems.com...
- Page 9 Contents of the Accessory Bag VGA Cable (D-sub) Power Cord –black OSD Remote Control 2 piece batteries (AAA) inside. USB Cable VT420 Series www.vartechsystems.com...
-
Page 10: Dimension (Front & Back)
Dimension (Front & Back) VT420 Series www.vartechsystems.com... -
Page 11: Installation
Main power –Switch & AC socket “—“ is power on “O” is power off Power Interface Main interface- switch & AC socket. Please see the chapter “Power input ” Side controller of the monitor The remote control (RCU ) VT420 Series www.vartechsystems.com... -
Page 12: Input Source Connection
Advanced ver. SPDIP output x 1 All Models Y-Pb-Pr (Y-Cb-Cr) input x 1 RCA G/B/R Advanced ver. Audio for Component input x 1 RCA L/R Advanced ver. 10 S-video input x 1 Mini Din 4 pin Advanced ver. VT420 Series www.vartechsystems.com... - Page 13 All Mo dels 13 Power cord input AC input All Models 14 AC switch ON/OFF All Models 15 RS232 for Touch D-Sub 9 pin Optional for AVT version 16 Touch USB Type B Female AVT version only VT420 Series www.vartechsystems.com...
-
Page 14: Operating The Monitor
The Side Controller Of The Monitor OSD Key Pad function List Descriptions Power Power on/Power off Source Source selection (toggle) Menu Right/Volume + Menu Left/Volume - ⊳ ⊳ ⊳ ⊳ Menu Up Menu Down Menu/Exit Menu/Exit selection VT420 Series www.vartechsystems.com... - Page 15 Select LED on via menu (Front LED: On) AC off Power on Select LED on via menu (Front LED: Off) LED OFF: The LED turns completely off when in the “off” mode regardless of the monitor being on or off. VT420 Series www.vartechsystems.com...
-
Page 16: The Remote Control (Rcu ) Instructions
Lock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence and OSD will be locked. Unlock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence again and OSD will be unlocked. VT420 Series www.vartechsystems.com... -
Page 17: Change The Rcu Battery
Battery to be used according to the instruction CAUTION About the remote control Don’t drop, shake or bump. Don’t place on wet materials. Don't dismantle. Don’t place in locations with exposure to high-temperature or high-humidity levels. VT420 Series www.vartechsystems.com... -
Page 18: Display Mode
HDMI 1 HDMI 2 Component (AA version only) S-Video (AA version only) Composite Video (AA version only) DVI (AA version only) HD-SDi (AA version option) When the monitor cannot find a source, a “No signal” message will appear. VT420 Series www.vartechsystems.com... - Page 19 To change the size and position of the sub-source: Using the remote, press P-POSITION to toggle through the options. Top Left Top Right Small PIP Main Bottom-Left Bottom- Right To switch the main source and the subsource: Using the remote, press SWAP. SWAP Main VT420 Series www.vartechsystems.com...
- Page 20 Side by Side (Picture-by-Picture): Press P-POSITION button choose “Side by side” mode, then the main source and the subsource will be on the screen display. Main PIP Screen Table HDMI 1 HDMI 2 Component S-Video Video HDMI 1 － － HDMI 2 － － － Component － S-Video － Video － VT420 Series www.vartechsystems.com...
- Page 21 Adjust the OSD rotation 0°/90°/180°/270° Settings OSD Language Select the OSD language English/ Chinese OSD Timeout Select the OSD timeout seconds 5~120 sec. Sleep Timer Select the sleep timer Off, 15,30,60,90,120 Min. Real Time Clock Setup Date & Time VT420 Series www.vartechsystems.com...
- Page 22 Reset to the factory default setting Yes, No VGA ADC Settings User ADC calibration Source Show the name of input source System Channel Resolution Show the current resolution Status Information Firmware Show the firmware of the monitor Version VT420 Series www.vartechsystems.com...
- Page 23 Adjust the OSD rotation 0°/90°/180°/270° Settings OSD Language Select the OSD language English/ Chinese OSD Timeout Select the OSD timeout seconds 5~120 sec. Sleep Timer Select the sleep timer Off, 15,30,60,90,120 Min. Real Time Clock Setup Date & Time VT420 Series www.vartechsystems.com...
- Page 24 Reset to the factory default setting Yes, No VGA ADC Settings Disabled if not a VGA mode Source Show the name of input source Channel Resolution Show the current resolution System Information Status Firmware Show the firmware of the monitor Version VT420 Series www.vartechsystems.com...
-
Page 25: On-Screen Display (Osd)
Press MENU to return to the previous menu. To exit the menu system, press EXIT. Image Settings Menu This menu is used for making common image adjustments. Image settings – Main setting Display settings Audio Settings (AA option) Basic Settings VT420 Series www.vartechsystems.com... -
Page 26: System Status
System Status Advanced Settings VT420 Series www.vartechsystems.com... - Page 27 Increases or decreases the green hue (Only Video Mode). Press or , select the desired level, and then press ENTER. Range: 0~100; Default: 50 Back Light Range: 0~100; Default: 80 Color Temp and Adjusts red, green, blue gain and red, green blue offset. Gamma VT420 Series www.vartechsystems.com...
- Page 28 Default: 0 Green Offset Set Color Temperature to “User Mode” in order to adjust this setting. Range: -50~50 Default: 0 Blue Offset Set Color Temperature to “User Mode” in order to adjust this setting. Range: -50~50 Default: 0 VT420 Series www.vartechsystems.com...
-
Page 29: Display Settings Menu
Default: Full screen Side by Side Scale Submenu Options: Zoom In, Zoom Out, Main, PIP, Default and Return Auto Scan Options: On, Off Default: On Select Source Options: HDMI1, HDMI2, VGA, Component, S-Video and Video Default: VGA VT420 Series www.vartechsystems.com... -
Page 30: Audio Settings Menu
Default: 10 Balance Adjust the balance of the left and right speakers. Press , select the desired level, and then press ENTER. Range: 0~20 Default: 10 HDMI Audio Input Select HDMI and PC audio input mode. Default: HDMI VT420 Series www.vartechsystems.com... -
Page 31: Basic Settings Menu
Press to select the desired time limit. Options: Off, 15, 30, 45, 60, 90, 120 Min Default: Off Real Time Clock Set date, and switch alarm on and off. Use , ,⊳, to adjust these options. VT420 Series www.vartechsystems.com... -
Page 32: Advanced Settings Menu
Baud Rate Options: 115200, 38400, 19200, 9600 Default: 115200 Monitor ID Options: 1~ 255 Default: 0 Light Sensor Options: On and Off Default: Off Factory Reset Restores all settings to their default. Options: No, Yes Default: No VT420 Series www.vartechsystems.com... -
Page 33: System Status Menu
(the black and white image can be made using software like Microsoft PowerPoint) The white in the left green box has to be the brightest white. iii. The black in the right green box has to be the darkest black. VT420 Series www.vartechsystems.com... -
Page 34: Default Setting
After calibration is completed, the display will notify user if the process is done successfully by different messages. Default Setting Item Default Value Brightness Scheme Users Contrast Color temp. 9300K Language English Gamma Over-scan Auto Scan Default input HDMI 1 Power status IRFM Baud rate 115200 VT420 Series www.vartechsystems.com... -
Page 35: Touch Operation
2500 Series latest driver. Follow the direction in the NW Multitouch Device Driver Installation Guide (part of the compressed file along with the driver) to install the driver. Once the driver is installed, restart the PC and the touch function is ready to go with MS Windows 2000/XP/Vista/7. VT420 Series www.vartechsystems.com... -
Page 36: Supported Timing
74.176 74.25 1080i 28.13 74.25 1920x1080 33.716 59.94 74.176 HDTV 33.75 74.25 74.25 33.75 74.25 1080p 1920x1080 56.25 148.5 67.433 59.94 148.352 67.5 148.5 V means supported the timing. 480i means supported 480i@60Hz(YPbPr). 576i means supported 576i@60Hz(YPbPr) VT420 Series www.vartechsystems.com... -
Page 37: Specification
Finger, gloved hand, or any other pointer Touch Interface USB (type B female) Function Transmittance (42AVT) Windows 98/NT/2000/XP/Vista/7 (driver required), Mac OS Operating System and Linux Input connecters available on Advanced version only HD-SDi is an option with the Advanced version option. VT420 Series www.vartechsystems.com... -
Page 38: Troubleshooting
: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. EN 55022 、EN 61000-3-2、EN-61000-3-3 EN 55024、IEC61000-4 EN 60950 [Low-Voltage Directive (73/23/EEC)] VT420 Series www.vartechsystems.com... -
Page 39: Appendix I
Moving the monitor requires at least two people. If not, it may drop and a serious injury may result. Moving/shipping the monitor, please hold the white handles. Carrying Notice : This monitor is heavy, please follow as below instruction, when you ready to carry the monitor. If not, it may cause an injury. VT420 Series www.vartechsystems.com... -
Page 40: Appendix Ii
3. Align the stand brackets with the mounting holes and attach the brackets to the monitor using the screws removed in Step 2. 4. Caution: Longer screws will damage the monitor. Remove the 4 screws from back of the monitor Use maximum 15mm/0.59” long screws. 8mm Metric VT420 Series www.vartechsystems.com... - Page 41 Step3. Align the wall brackets with the mounting holes and attach the brackets to the monitor using the screws removed in Step 2. Caution: Longer screws will damage the monitor. Remove the 4 screws from back of the monitor Use maximum 15mm/0.59” long screws. 8mm Metric VT420 Series www.vartechsystems.com...
-
Page 42: Appendix Iii
Appendix III Wall mounting safety Notes VT420 Series www.vartechsystems.com... - Page 43 VT420 Series www.vartechsystems.com...