Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Broadcast Tools Manuals
  4. Remote Control
  5. SRC-8 III
  6. Installation and operation manual

Broadcast Tools SRC-8 III Installation And Operation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
®
Installation and Operation Manual
SRC-8 III
Serial Remote Control
Firmware version: 1.16
Manual Revised 10/15/2004
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
Copyright, 1989 - 2005 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.

Advertisement

loading
Need help?

Need help?

Do you have a question about the SRC-8 III and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Broadcast Tools SRC-8 III

Summary of Contents for Broadcast Tools SRC-8 III

  • Page 1 Manual Revised 10/15/2004 Due to the dynamic nature of product design, the information contained in this document is subject to change without notice. Broadcast Tools, Inc., assumes no responsibility for errors and/or omissions contained in this document. Revisions of this information or new editions may be issued to incorporate such changes.

  • Page 2: Table Of Contents

    SRC-8 III Installation and Operation Manual Table of Contents Section Title Page # Introduction ......... . . 3 Safety Information .

  • Page 3: Introduction

    SRC-8 III Installation and Operation Manual INTRODUCTION CAUTION! Thank you for your purchase of a Broadcast Tools® SRC-8 III, Serial Remote Broadcast Tools® Control (referred to as the SRC-8 III throughout this manual). We’re confident Products, as with any that this product will give you many years of dependable service. This manual...

  • Page 4: Product Description

    8-channles of control in each direction. The unit can communicate using RS-232, RS-422 or RS-485 at data rates up to 38400. The SRC-8 III may be expanded to 32 inputs x 32 outputs. Optional external Ethernet and USB capabili- ties may be added.

  • Page 5: Installation Guidelines

    The Baud rate will be set by the dipswitch on power up or reset. It can also be changed using the serial port commands at other times, but if the SRC-8 III is reset baud rate will be set according to the dipswitch settings.
  • Page 6 (OFF) is ASCII mode. Refer to the ASCII pro- tocol below for ASCII commands. DIP 6 = (ON) Pair mode, inputs from one SRC-8 III will map directly to outputs of another SRC-8 III when connected together via RS-232 or RS422. (OFF) normal operation via RS-232/422.
  • Page 7 “EXT-J14”. Connect one end of the supplied ribbon cable to the “EXT-12” header on the first SRC-8 III and the other end of the ribbon cable to the “EXT-14” header of the next unit and so on. Each board should have a unique address set on its dipswitch address setting.
  • Page 8 Binary commands must be received as a packet. If 50 ms or more passes after a WEBSITE: character is received, with no new character following, the SRC-8 III will begin looking for a new string if no valid data packet has been received.
  • Page 9 SRC-8 III Installation and Operation Manual Command Additional Data Bytes Function Disable error & good responses Latch output n (00 – 07) Unlatch output n (00 – 07) Pulse output n (00 – 07), t= time (1-63h =.1-9.9sec) Poll output n (00 – 07) (see 55h) Poll input n (00 –...

  • Page 10: Specifications

    SRC-8 III Installation and Operation Manual SPECIFICATIONS Digital Inputs: 8 – Selectable 5 to 24 vdc optically Isolated or 5-volt TTL/CMOS logic compatible input (Jumper selectable. Factory default = Wet). 50 ms minimum duration. Relay Outputs: 8 – SPDT, 1 amp/30 vdc relays. Jumper selectable either N.O or N.C.

  • Page 11: Warranty

    If Broadcast Tools is notified, in writing, of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned in to Broadcast Tools in accordance with Broadcast Tools’...
  • Page 12 Sedro-Woolley, WA 98284 • USA 360.854.9559 voice • 360.854.9479 support@broadcasttools.com e-mail www.broadcasttools.com website Visit the Broadcast Tools website or contact us via e-mail, phone, or fax for more information, additional manuals, and a list of dealers. © 2005 Broadcast Tools, Inc. All Rights Reserved...