HHB CDR-850 Service Manual page 81

7.3.3 About the detailed error code
In CDR-850, when "SKIP PLAY" key and "MENU" key are pushed
at the same time on the ordinary mode, the error code of details is
displayed in FL display. As for the error code of details, the packing
improvement is not done. When the power supply is turned off, the
error code of details is deleted.
The display of eight digits is as follows.
8 8 8 8
1 2
The value of two digits (eight digits in total) displayed in 1-4 is
displayed as follows.
Two digits displayed in 1 : Operation when figure of digit of
subordinate position does error
detection.
* 0: Uncertainty
* 1: Tray OPEN
* 2: Tray CLOSE or STOP
* 3: SET_UP (disk start-up)
* 4: TOC and PMA lead (SET_UP is included)
* 5: PLAY
* 6: SERCH
* 7: REC/PAUSE
* 8: REC
* 9: Lead OUT REC
* A: TOC REC
* B: PMA REC
* C: Power CALIBRATION
* D: TOC CHECK
* E: ACTUAL PAUSE REC
* F: Uncertainty
However, when "F1" is displayed in 2, the NG pin number
of mechanism contoller is displayed in 1.
Two digits displayed in 2 : Error mode.
Mode No. or even 0-79 is an error where mechanism contoller is
generated.
Mode No.; Mode name.
00; Irregular mode (An internal uncertain state, at hard
reset).
01; Invalid mode.
02; STOP.
03; Laser diode turning on (reproduction power).
04; Focus 0N.
05; Spindle ON.
06; Tracking ON.
07; DIRC use direct sequence forward 1 truck jump.
08; DIRC use direct sequence reverse 2 truck jump.
8 8 8 8
3 4
09; DIRC use direct sequence forward 1 truck Jump
repeat.
10; DIRC use direct sequence reverse 1 truck Jump
repeat.
11; Auto sequence 10 truck forward jump repeat.
12; Auto sequence 10 truck reverse jump repeat.
13; Auto sequence 50 truck forward jump repeat.
14; Auto sequence 50 truck reverse jump repeat.
15; Auto sequence forward M truck move.
16; Auto sequence reverse M truck move.
17; PAUSE.
18; PLAY.
19; Seek truck 0.
20; Search at blank.
21; REC.
22; REC to PAUSE (REC END).
23; ATIP TIME search.
24; Q code TIME search.
25; Q code truck search.
26; forward 300 truck move.
27; reverse 300 truck move.
30; TOC area search.
31; Tray open.
32; Tray close.
33; Setup (to PLAY).
34; TOC lead.
35; PLAY normal.
36; Search to PLAY.
37; REC PAUSE.
39; Lead out REC.
40; TOC REC (lead Inn).
41; PMA REC.
42; PCA REC.
43; TOC check.
44; ACTUAL REC PAUSE.
45; Initialization.
47; 2Tr JUMP specification at PAUSE.
48; 1Tr JUMP specification at PAUSE.
51; Search to PAUSE.
52; PMA lead.
53; Ratings record of Laser diode power output.
54; Searches the area where is Q code.
57; maximum record ofLaser diode power output.
58; Record power of Laser diode continuous sweep
mode.
59; Slider forward move.
60; Slider reverse move.
61; The line speed and the track pitch of the disk are
calculated by T0 and Tl measurement.
62; Auto sequence 1 truck forward jump.
63; Auto sequence 1 truck reverse jump.
64; Auto sequence 1 truck forward jump repeat.
65; Auto sequence 1 truck reverse jump repeat.
66; Auto sequence 10 truck forward jump.
67; Auto sequence 10 truck reverse jump.
68; Scanning mode which uses auto sequence 10 truck
forward jump (It is a sound).
69; Scanning mode which uses auto sequence 10 truck
reverse jump (It is a sound).
CDR-850
81