Table of Contents

Advertisement

SIMPLY CLEVER
ŠKODA Rapid
Owner's Manual

Advertisement

Table of Contents
loading

Summary of Contents for Skoda Rapid

  • Page 1 SIMPLY CLEVER ŠKODA Rapid Owner's Manual...
  • Page 2  5JA012720AF...
  • Page 4 Preface You have opted for a ŠKODA – our sincere thanks for your confidence in us. The description of the vehicle operation, important information about safety, vehicle care, mainte- nance and self-help, as well as technical vehicle data, are given in this manual. Please read this Owner's Manual carefully, because operation in accordance with these instructions is a prerequisite for proper use of the vehicle.
  • Page 5: Table Of Contents

    MAXI DOT display Retraction and economical driving Table of Contents Service interval display Driving through water and driving off of made-up roads Board literature Unlocking and opening Assist systems Unlocking and locking Notes Braking and stabilisation systems Anti-theft alarm system Structure and more information about the Parking aid Luggage compartment lid...
  • Page 6 Do-it-yourself Emergency equipment and self-help Emergency equipment Reserve and temporary spare wheel Changing a wheel Puncture set Jump-starting Towing the vehicle Remote control Emergency unlocking/locking Replacing windscreen wiper blades Fuses and light bulbs Fuses Replacing bulbs Technical data Technical data Vehicle data Index Table of Contents...
  • Page 7: Board Literature

    Move Brochure Board literature The Move brochure contains phone numbers of importers and service offices in individual countries, together with emergency numbers. You always find these Operating Instructions and the Service Plan in the on- board literature for your vehicle. Depending on the equipment, the on-board literature can also contain The ra- dio instruction manual or Manual of the navigation systemand in some coun- tries also the brochure On the road.
  • Page 8: Notes

    Note Notes Texts with this symbol contain additional information. Terms used The on-board literature contains the following terms relating to the service work for your vehicle. “Specialist” - Workshop - a workshop that carries out specialist service tasks for ŠKODA vehicles. A specialist can be a ŠKODA Partner, a ŠKODA Serv- ice Partner, or an independent workshop.
  • Page 9: Structure And More Information About The Operating Instructions

    Structure and more information about the Operating Instructions Structure of the manual The operating manual is hierarchically divided into the following areas. Section (e.g. Safety) - the title of the Section is always indicated at the lower ■ left side Main chapters (e.g.
  • Page 10: Abbreviations

    Abbreviation Definition Abbreviations Diesel engine with turbo charging and common rail injection TDI CR Abbreviation Definition system Engine revolutions per minute Petrol engine with turbocharging and direct injection a Bluetooth software profile for a one-way transfer of audio Vehicle identification number A2DP data Wi-Fi...
  • Page 11: Safety Passive Safety

    Check the tyre inflation pressure.  Safety Check the engine oil, brake fluid and coolant level.  Secure all items of luggage. Passive Safety  Do not exceed the permissible axle loads and permissible gross weight of  the vehicle. General information Close all doors as well as the bonnet and boot lid.
  • Page 12: Correct And Safe Seated Position

    › Head airbags. WARNING (Continued) › Anchoring points for child seats using the ISOFIX system. If the occupants on the rear seats are not sitting upright, the risk of injury ■ › Anchoring points for child seats using the TOP TETHER system. is increased due to incorrect routing of the seat belt.
  • Page 13: Adjusting The Steering Wheel Position

    › Pull the holder until it stops in arrow direction WARNING Always assume the correct seated position before setting off and do not ■ WARNING change this position while driving. Also advise your passengers to adopt The lever for adjusting the steering wheel must be locked whilst driving ■...
  • Page 14: Correct Seated Position For The Passengers In The Rear Seats

    Do not lean out of the window.  Correct seated position for the passengers in the rear seats Do not put your feet out of the window.   Read and observe on page 9 first. Do not put your feet on the dash panel. ...
  • Page 15: Seat Belts

    WARNING Seat belts Fasten your seat belt before each journey – even when driving in town! ■ This also applies to the passengers seated at the rear – risk of injury! Using seat belts Expectant women must also always wear a seat belt. This is the only way ■...
  • Page 16 WARNING (Continued) The physical principle of a frontal collision The lock tongue should only be inserted into the lock which is the correct ■ one for your seat. Wrong use of the safety belt will reduce its capacity to protect and the risk of injury increases. The slot of the belt tongue must not be blocked, otherwise the belt ■...
  • Page 17 › It is also important that rear passengers fasten their seat belts, as they could Use the lock tongue to slowly pull the webbing over your chest and pelvis. › otherwise be thrown through the vehicle in an uncontrolled manner in the Insert the lock tongue into the belt buckle for the seat »...
  • Page 18: Inertia Reels And Belt Tensioners

    Belt height adjustment on the front seats Belt tensioners Safety for the driver and front passenger wearing their seat belts is enhanced Fig. 7 by the belt tensioners fitted to the inertia reels of the front three-point seat Front seat: Seat belt height ad- belts.
  • Page 19: Airbag System

    Airbag system System description  Read and observe on page 16 first. Description of the airbag system The functional status of the airbag system is indicated by the indicator light   Introduction in the instrument cluster » page This chapter contains information on the following subjects: When the airbags are deployed, they fill with gas and inflate.
  • Page 20: Airbag Overview

    Deployment factors Front airbags It is not possible to generally determine which deployment conditions apply to the airbag system in every situation. An important role is played by factors such as the type of object that the vehicle hits (hard/soft), the impact angle, vehicle speed etc.
  • Page 21 WARNING Note Information on correct seated position In vehicles with head airbags, the lettering  can be seen on the steering ■ For the driver and front passenger, it is important to maintain a distance wheel. ■ In vehicles with front passenger airbags, the lettering  is located on the of at least 25 cm from the steering wheel or dashboard »...
  • Page 22 WARNING (Continued) Head airbags There must not be any further persons, animals or objects positioned be- ■ tween the occupants and the deployment area of the airbag. No accesso- ries, such as cup holders, should be attached to the doors. If children adopt an incorrect seated position when travelling, they may ■...
  • Page 23: Deactivating Airbags

    The front passenger airbag can be switched off with the key-operated WARNING (Continued) switch » page The installation of impermissible accessories in the vicinity of the head ■ airbags can considerably impair the protection offered by the head airbag in We recommend that you ask a ŠKODA service partner to deactivate any other the event of it being deployed.
  • Page 24 Switching off CAUTION › Switch off the ignition. An insufficiently folded out key bit can damage the key switch! › Open the storage box on the front passenger's side. › Fold the key bit out completely for the radio key »...
  • Page 25: Transporting Children Safely

    WARNING (Continued) Transporting children safely Children are exposed to an increased risk of injury in the event of an acci- ■ dent if they lean forward or adopt an incorrect seated position when the Child seat vehicle is moving. This particularly applies to children who are transported ...
  • Page 26 › If possible, move the front passenger seat backwards so that there is no con- Use of a child seat on the front passenger seat tact between the front passenger seat and the child seat behind it. › Does not apply to Taiwan With child safety seats in groups 2 or 3, make sure that the loop-around fit- tings attached to the child seat headrest is positioned in front of or at the same height as the loop-around fittings on the B pillar on the passenger side.
  • Page 27 WARNING Use of the child seat in the front passenger seat Children must never be seated with their head in the deployment area of ■ Applies to Taiwan the side airbag – risk of injury! Do not place any objects within the deployment area of the side airbags – ■...
  • Page 28: Fastening Systems

    “Universal” child seat category - a child seat designed to be attached to  represents a system for a fast and secure child seat mounting. the seat using the seat belt. There are two locking eyes between the rear exterior seats for fixing the child seat in place, using the -system.
  • Page 29 Size class of Group Front passenger seat Outer rear seats Rear seat middle the child seat IL-SU 9 - 18 kg IL-SU 15 - 25 kg IL-SU 22 - 36 kg The size category is shown on the label attached to the child seat. IL-SU The seat is suited for installation of a -child seat with the “Semi- WARNING...
  • Page 30 Transporting children safely...
  • Page 31 Fig. 19 Cockpit Using the system...
  • Page 32: Using The System

    Door opening lever Using the system Light switch Headlight range control (in the dashboard) Cockpit Bonnet release lever Overview Fuse box in the dashboard Lever for adjusting the steering wheel Electrical power windows Ignition lock Door opening lever Pedals Electric exterior mirror adjustment Storage compartment Air outlet vents Handbrake lever...
  • Page 33: Instruments And Indicator Lights

    Instruments and Indicator Lights Overview Instrument cluster  Introduction This chapter contains information on the following subjects: Overview Revolution counter Display Speedometer Coolant temperature gauge Fuel gauge Counter for distance driven Fig. 20 Instrument cluster - Version 1 Display of the second speed Auto Check Control The instrument cluster gives the driver basic information such as the current speed, engine speed, the state of some vehicle systems and the like.
  • Page 34 Speedometer » page 31 Display › with warning lights » page 34 Button for display mode: Fig. 22 › Time settings » page 33 Display types › Enable/disable the display of the second speed » page 33 › Service intervals - Display of the number of days and kilometres remain- ing until the next service »...
  • Page 35 Warning at excessive speeds CAUTION An audible warning signal will sound when the vehicle speed exceeds 120 km/ Additional headlights and other attached components in front of the air inlet ■ . The audible warning signal is switched off when the vehicle speed falls be- impair the cooling efficiency of the coolant.
  • Page 36 CAUTION Note Never drive until the fuel tank is completely empty! The irregular supply of fuel If the second speed display is enabled on vehicles with a segment display, this can cause misfiring. This can result in considerable damage to parts of the en- speed will be shown instead of the odometer.
  • Page 37: Indicator Lights

    Some error messages and other information are displayed in the MAXI DOT WARNING display. The messages are displayed simultaneously with the icons in the MAXI If you have to stop for technical reasons, then park the vehicle at a safe DOT display or with the warning lights in the instrument cluster »...
  • Page 38: The Warning Triangle Must Be Set Up At The Pre- Scribed Distance - Observe The National Legal Provisions When Doing So

    Tyre inflation pressure  Brake system  Windscreen washer fluid level   Read and observe on page 35 first. Turn signal system   Fog lights  The indicator light illuminates if the brake fluid level in the braking system ...
  • Page 39: Engine Oil Sensor Defective

    If the engine oil level sensor is faulty, the warning light flashes several CAUTION  times and an audible signal sounds when the ignition is turned on. If in addition to the warning light the warning light » page 36lights up ...
  • Page 40: Power Steering

    If the warning light does not illuminate after you switch the engine back on, WARNING  the ESR is fully functional again. Carefully open the coolant expansion bottle. If the engine is hot, the cool- ■ ing system is pressurized – risk of scalding! It is therefore best to allow the Further information »...
  • Page 41: Rear Fog Light

    The following message is shown in the MAXI DOT display. Exhaust inspection system  Error: ABS   Read and observe on page 35 first. The vehicle will only be braked by the normal brake system without the ABS. If the warning light illuminates, there is a fault in the exhaust inspection ...
  • Page 42: Fuel Reserve

    To clean the filter, and where traffic conditions permit » , drive as follows for Fuel reserve  at least 15 minutes or until the indicator light goes out.   Read and observe on page 35 first. 4th or 5th gear selected (automatic transmission: position S). ...
  • Page 43 WARNING CAUTION When a fault in the airbag system occurs, there is a risk of the system not Under certain circumstances (e.g. sporty style of driving, wintry or unpaved being triggered in the event of an accident. Therefore, this must be roads) the warning light in the instrument cluster can be delayed or does ...
  • Page 44: Information System

    Cruise control system Information system   Read and observe on page 35 first. Driver information system The warning light illuminates when the cruise control is active » page 111.   Introduction Brake pedal (automatic gearbox)  This chapter contains information on the following subjects: ...
  • Page 45 Using the information system Display a low temperature  Read and observe on page 41 first. Prompt in the MAXI DOT display If the outside temperature while driving drops to below +4°C, the following icon appears on the display in front of the temperature display . An audible signal is emitted.
  • Page 46: Multifunction Display (Mfd)

    WARNING Gear recommendation The driver is always responsible for selecting the correct gear in different driving situations, such as overtaking. Fig. 27 Information on the selected For the sake of the environment gear / Gear recommendation A suitably selected gear has the following advantages. It helps to reduce fuel consumption.
  • Page 47: Fig. 28

    The multifunction display only operates when the ignition is switched on. After Display of the selected memory in the display at the position » Fig. 28 the ignition is switched on, the function that was last selected before switch- Single-trip memory ...
  • Page 48: Information Overview

    The display is shown in steps of 10 km. After lighting up of the indicator light  Information overview the display is shown in steps of 5 km.  Read and observe on page 44 first. The fuel consumption over the last 50 km is used to calculate the information. The range will increase if you drive in a more economical manner.
  • Page 49: Maxi Dot Display

    Warning at excessive speeds MAXI DOT display Set the speed limit, e.g. for the maximum permissible speed in urban areas » page 46, Warning at excessive speeds.  Introduction This chapter contains information on the following subjects: Warning at excessive speeds Main menu ...
  • Page 50: Service Interval Display

    Alt. speed dis. Note Here, the display of the second speed in mph can be activated. If warning messages are displayed, these messages must be verified to ac- ■ cess the main menu » page 42, Using the information system. Further information »...
  • Page 51 Note Prompt in the segment display Information is retained in the Service Interval Display even after the vehicle battery is disconnected. Fig. 29 Segment display: Example of a Prompt in the MAXI DOT display message Oil change service If an oil change service is due, the following message appears: Oil change in ... km or ...
  • Page 52: Unlocking And Opening

    Information on the oil change service is displayed at first, followed by informa- Unlocking and opening tion on the inspection when button is pressed again. › The number 1 or 2 is displayed in position Unlocking and locking › The symbol  and the number of days remaining until the next service inter- val are displayed in position ...
  • Page 53: With The Key On The Lock Cylinder Unlock / Lock

    › The SafeLock system is switched on. With the key on the lock cylinder unlock / lock › The warning light in the driver door begins flashing. › The anti-theft alarm system is activated. Fig. 30 If the doors or the boot lid remain open after the vehicle has been locked, the Left side of the vehicle: Turning turn signal lights do not flash until they have been closed.
  • Page 54: Opening/Closing A Door

    Unlocking / locking the boot lid Opening from the inside › Briefly pressing the symbol key unlocks the boot lid. After unlocking, the Pull on door opening lever of the respective door and push the door away boot lid can be opened with the button in the handle above the number plate. from you.
  • Page 55: Individual Settings

    Switch-off display Locking and unlocking the vehicle with the central locking button The indicator light in the driver door flashes for about 2 seconds fast, goes out and starts to flash at longer intervals after about 30 seconds. Fig. 33 Switch-on display Central locking button The warning light flashes for around 2 seconds in quick succession, afterwards...
  • Page 56: Anti-Theft Alarm System

    Discharged battery in the remote control key Child safety lock If the red indicator light » Fig. 31 on page 50 does not flash when you press a button on the remote control key, the battery is empty. Replace the battery »...
  • Page 57: Luggage Compartment Lid

    Deactivating Note › Switch off the ignition. The working life of the alarm siren is 5 years. › Open the driver door. › Press the symbol button  » Fig. 35 on the B column of the driver's side. Activating/deactivating The illumination of the symbol ...
  • Page 58: Power Windows

    Delayed locking can be deactivated by a specialist garage at any time. Note The function of the button in the grip above the licence plate is deactivated CAUTION when starting off or at a speed of 5 km/hour or more for vehicles with central There is a risk of unwanted entry into the vehicle before the boot lid is locked locking.
  • Page 59 The driver's window can be completely opened automatically by briefly press- Note ing the button as far as it will go. Renewed pressing of the button causes the When driving always use the existing heating, air conditioning and ventila- ■ window to stop.
  • Page 60: Mechanical Windows

    Mechanical windows Open / close window  Introduction This chapter contains information on the following subjects: Open / close window The window can be operated mechanically by means of the handle attached to the respective door panel. WARNING The windows should nevertheless be closed carefully – risk of injury! Fig.
  • Page 61: Lights And Visibility

    WARNING (Continued) Lights and visibility The automatic driving lamp control  only operates as a support and ■ does not release the driver from his responsibility to check the lights and, if Lights necessary, to switch on the light depending on the prevailing light condi- ...
  • Page 62: Daytime Running Lights(Day Light)

    Switching on the parking light or parking lights » page 63  Daytime running lights(DAY LIGHT) Switch on low beam   Read and observe on page 58 first. Pull switch The daytime running lights (the only function) provides the lighting of the front Switch on the front fog lamp »...
  • Page 63: Turn Signal And Main Beam

    › Release the turn signal stalk. When the right flashing light is switched on, the warning light flashes in the  instrument cluster. WARNING The turn signal light switches itself off automatically when driving around a When the daytime running light is switched on, the side lights (neither at curve or after making a turn.
  • Page 64: Fog Lights

    Automatic driving light control during rain Fog lights with CORNER function The low beam lights are switched on automatically if the following conditions  are met. Read and observe on page 58 first. The light switch is in position  »...
  • Page 65: Coming Home / Leaving Home

    CAUTION COMING HOME / LEAVING HOME Do not attach any stickers or similar objects in front of the light sensor on ■  Read and observe on page 58 first. the windscreen to avoid impairing the function or its reliability. If this function is activated constantly, the battery will be heavily discharged ■...
  • Page 66: Interior Lighting

    Parking light Interior lighting  Read and observe on page 58 first.  Introduction The parking light is provided for a temporary lighting of the parked vehicle. This chapter contains information on the following subjects: Parking light  switching on Front interior light ›...
  • Page 67: Visibility

    The system is turned off when any of the following is present. Rear window heater › The vehicle is locked. › The ignition is switched on. › Fig. 46 About 30 seconds after all the doors have been closed. Dash panel: Button for rear win- dow heater Rear interior light Fig.
  • Page 68: Windscreen Wipers And Washers

    Top up with windscreen wiper fluid » page 139. Front sun visors WARNING Properly maintained windscreen wiper blades are essential for clear visi- ■ bility and safe driving » page 168. Replace the windscreen wiper blades once or twice a year for safety rea- ■...
  • Page 69: Rear Mirror

    Slow windscreen wiping  page 66), when the low beam or main beam is switched on. Rapid windscreen wiping  You should remove stubborn dirt (such as insect residues) from the headlight Flick windscreen wiping, service position of the wiper ...
  • Page 70 When the interior lights are switched on or the reverse gear is engaged, the WARNING mirror always moves back into the basic position (not dimmed). Make sure that the mirror is not covered by ice, snow, mist or other ob- ■...
  • Page 71 Note Exterior mirror The mirror heater only operates when the engine is running and up to an ■ outside temperature of +35 ℃. If the electrical mirror setting fails at any time, the mirrors can be adjusted by ■ hand by pressing on the edge of the mirror surface. Fig.
  • Page 72: Seats And Head Restraints

    Seats and head restraints Adjusting the front seats Seats and head restraints Fig. 51 Control elements at the seat  Introduction This chapter contains information on the following subjects: Adjusting the front seats Head restraints - adjusting height Headrests - removing and installing The driver's seat should be adjusted in such a way that the pedals can be fully ...
  • Page 73 Head restraints - adjusting height Headrests - removing and installing Fig. 52 Head rests: move upwards / move downwards Fig. 53 Front head rests: remove / install  Read and observe on page 69 first. Adjustment of the head rest heights is the same in the front and rear. Best protection is achieved if the top edge of the head rest is at the same level as the upper part of your head.
  • Page 74: Seat Features

    › To re-insert the head restraint, push it far enough down in the direction of Switching on › arrow into the seat backrest until the locking button clicks into place. Press the corresponding symbol button  or  » Fig. Pressing once switches the seat heating on at its maximum level - Level 2.
  • Page 75 Front armrest Seat backrests Fig. 56 Adjusting armrest Setting the height Fig. 58 Fold seat backrest forwards / pull seat belt to the side panel and › Lift the armrest fully upwards in the direction of the arrow » Fig. 56 and then ready position of the seat belt move it back down completely.
  • Page 76: Transporting And Practical Equipment

    › Then push the seat backrest back into the upright position until the securing Transporting and practical equipment knob clicks into place – check by pulling on the seat backrest » › Make sure that the red pin is hidden. Useful equipment Fold back undivided seat backrest ›...
  • Page 77: Car Park Ticket Holder

    WARNING Car park ticket holder Do not use the storage compartment » Fig. 60 of the door pocket to store projecting objects. These could impair the effectiveness of the side Fig. 59 airbag. Parking ticket holder Storage compartment in the centre console ...
  • Page 78: Cigarette Lighter

    Cigarette lighter Fig. 63 Cup holder in rear armrest Fig. 64 Cigarette lighter  Read and observe on page 73 first.  Read and observe on page 73 first. Two beverage containers can be placed into the cup holder. Placement of the cup holders »...
  • Page 79: Ashtray

     Read and observe on page 73 first. Ashtray › Remove the socket cover or the cigarette lighter » Fig. › Connect the plug for the electrical appliance to the socket. The socket also operates if the ignition is switched off .»...
  • Page 80: Waste Container

    › Push the two catches of the inner frame out of the container body in the di- Waste container rection of the arrow » Fig. › Pull the bag together with the inner frame down in the direction of arrow ›...
  • Page 81: Storage Compartment In The Front Arm Rest

     Read and observe on page 73 first. Storage compartment in the front arm rest Opening › Press on the lid of the glasses storage box in area » Fig. The box folds in the direction of the arrow. Closing ›...
  • Page 82: Clothes Hook

    › Open the cover in the direction of the arrow CAUTION The maximum permissible load of the hooks is 2 kg. Closing › Screw in the filler cap in the direction of arrow until it audibly clicks into Storage pockets on the front seats place »...
  • Page 83: Luggage Compartment

    Double-sided floor covering Net pockets on the front seat rest Class N1 vehicles Fig. 73 Please observe the following for the purpose of maintaining good handling Meshed pocket characteristics of your vehicle: › Distribute loads as evenly as possible. › Place heavy objects as far forward as possible.
  • Page 84: Fastening Elements

    The upper front lashing eye is located behind the folding rear seat backrest. WARNING (Continued) The transported items must be stowed in such a way that no objects are ■ CAUTION able to slip forward on sudden driving or braking manoeuvres – risk of in- The maximum permissible static load of the individual lashing eyes is 3.5 kN jury!
  • Page 85: Hooks

    Removing CAUTION › Unhook the retaining straps from the flap in the direction of arrow The maximum permissible load of the fixing nets is 1.5 kg. ■ » Fig. Do not place any sharp objects in the nets – risk of net damage. ■...
  • Page 86: Parking Position" Of The Boot Cover

     Read and observe on page 80 first. Note If the support straps » Fig. 78 are attached to the boot, then the boot cover The side compartment covers can be removed to increase the size of the lug- will raise when the boot is opened. gage compartment.
  • Page 87: Roof Rack

    CAUTION WARNING The cargo elements are designed for attaching loads with a maximum gross The transported items on the roof rack must be securely attached – risk ■ weight of 8 kg. of accident! Always secure the load with appropriate and undamaged lashing straps ■...
  • Page 88: Heating And Air Conditioning

    fixing points for base support Heating and air conditioning Heating, ventilation, cooling  Introduction This chapter contains information on the following subjects: Air outlet vents Air distribution control Heating Air conditioning (manual air conditioning) Climatronic (automatic air conditioning) Fig. 82 Attachment points Efficient handling of the cooling system ...
  • Page 89  Read and observe on page 85 first. WARNING (Continued) Under certain circumstances, air at a temperature of about 5 °C can flow ■ Warmed, not warmed fresh or cooled air will flow out of the opened air outlet out of the vents when the cooling system is switched on. vents according to the setting of the control and the outside atmospheric con- To reduce health risks (e.g.
  • Page 90: Air Distribution Control

    Note Air distribution control If recirculated air mode is switched on for around 15 minutes, the symbol   Read and observe on page 85 first. will begin to flash in the Climatronic display as a sign that the recirculated air mode is switched on long-term.
  • Page 91: Air Conditioning (Manual Air Conditioning)

    Air conditioning (manual air conditioning) Climatronic (automatic air conditioning) Fig. 85 Controls of the air conditioning Fig. 86 Controls the Climatronic   Read and observe on page 85 first. Read and observe on page 85 first. Individual functions can be set or switched on by turning the knob or pressing The Climatronic in automatic mode ensures the best-possible setting of the the respective button.
  • Page 92: Efficient Handling Of The Cooling System

    Switching automatic mode on Automatic mode can be switched off by pressing one of the buttons for the air  distribution or by increasing/decreasing the blower speed. The temperature is Switching the intensive windshield defroster on/off - when this function ...
  • Page 93: Communication And Multimedia

    If you are not able to resolve the operational problem yourself, or if the cooler Communication and multimedia output has reduced, switch off the cooling system and seek assistance from a specialist garage. Universal telephone installation GSM II  Introduction This chapter contains information on the following subjects: Introductory information Phone Phonebook...
  • Page 94 › Telephone operation in the MAXI DOT display » page WARNING (Continued) › Voice control of the telephone » page Never leave a mobile phone on a seat, on the dash panel or in any area ■ › Music playback from the telephone or other multimedia units »...
  • Page 95 Operating the phone on the multifunction steering wheel This applies only if your vehicle has been equipped with the universal tele- phone installation at the factory. The buttons control the functions for the operating mode of the current tele- phone. If the side lights are switched on, the buttons on the multifunction steering wheel are illuminated.
  • Page 96 › To finish pairing in the MAXI DOT display, confirm the creation of the new Symbols in the display user profile.  Read and observe on page 90 first. If there is no free space available to create a new user profile, delete an exist- ing user profile.
  • Page 97: Voice Control

    Solving connection problems Voice mailbox If the hands-free system reports No paired phone found, check the operating In the Voice mailbox menu item, you can set the number of the voice mailbox status of the mobile phone. and then dial the number. ›...
  • Page 98 Switching off voice control Dialogue If the system is currently playing a message, the message that is currently be- ing played must be terminated by briefly pressing button » Fig. 88 on the Fig. 88 multifunction steering wheel. Multifunction steering wheel: If the system is expecting a voice command, you can end the dialogue yourself Voice control as follows.
  • Page 99: Multimedia

    Voice command Action ® Music playback via Bluetooth ® SETTINGS Selection for setting Bluetooth , dialogue etc. The universal telephone preinstallation GSM II makes it possible to play back CANCEL The dialogue is ended. ® music via Bluetooth from the devices such as MP3 player, mobile phone or notebook.
  • Page 100: Fig

    Button/ Action Radio Audio sources Navigation wheel » Fig. 89 Press Change audio source Interrupt current navigation an- Press Switch tone off/on (MUTE ) nouncement Turn upwards Increase volume Turn downwards Decrease volume Skip to next channel Skip to next track No function Press briefly Interrupt traffic report...
  • Page 101: Smartgate

    AUX input WARNING For vehicles with an AUX input this depends on the equipment and is located The national legal regulations for using mobile communication devices in ■ at one of the following locations. a vehicle must be observed. › Between the front seats in the centre console »...
  • Page 102 Automatic connection Password Management The connection to SmartGate is automatically restored under the following  conditions. Read and observe on page 98 first. Wi-Fi is turned on in the device to be connected.  Password management can be done in the connected device on the Smart- The ignition is switched on.
  • Page 103: Driving

    WARNING Driving Never (e.g. in garages) run the engine in a closed place - there is the dan- ■ ger of poisoning and death! Starting-off and Driving Do not leave any items (e.g. cloths or tools) in the engine compartment. ■...
  • Page 104 The ignition is switched off. Lock/unlock steering lock Procedure for starting the engine  Read and observe on page 100 first. › Firmly apply the handbrake. › For vehicles with manual transmission, shift gear stick to neutral, depress The steering lock (steering lock) deters any attempted theft of your vehicle. the clutch pedal and hold it there until the engine starts.
  • Page 105: Brakes And Parking

    The engine and the ignition are switched off simultaneously. Information on braking For vehicles with automatic transmission, the ignition key can only be removed  Read and observe on page 102 first. if the selector lever is in position P . Wear-and-tear CAUTION The wear of the brake pads is dependent on the operating conditions and driv-...
  • Page 106: Manual Gear Changing And Pedals

    Low brake fluid level The following instruction is shown in the MAXI DOT display. An insufficient level of brake fluid may result in problems in the brake system. Release parking brake!  The level of the brake fluid is monitored electronically »...
  • Page 107: Automatic Gearbox

    In the driver's footwell, only a footmat, which is attached to the two corre- Manual gear changing sponding attachment points may be used. Only use factory-supplied footmats or footmats from the range of ŠKODAOrigi- Fig. 93 nal Accessories, which are fitted to two attachment points. Gearshift pattern of 5 gear or 6 gear manual gearbox WARNING...
  • Page 108 – Neutral CAUTION The power transmission to the drive wheels is interrupted in this mode. If the selector lever is moved to mode N while driving, the accelerator pedal ■ must be released and you will need to wait until the engine has reached its - Mode for forwards travel (normal programme) idling speed before moving the selector lever to a forward driving mode again.
  • Page 109 Shifting up gears › Push the selector lever forwards » Fig. WARNING Rapid acceleration, particularly on slippery roads, can lead to loss of vehicle Shifting down gears › control – risk of accident! Push the selector lever backwards » Fig. 95...
  • Page 110: Retraction And Economical Driving

    Avoid full throttle and high speeds Retraction and economical driving Fuel consumption will be halved if you drive at only three-quarters of the pos- sible top speed of your vehicle.  Introduction Reducing idling This chapter contains information on the following subjects: When the engine is switched off, such as when waiting in a traffic jam, the fuel Driving in economy is already greater after 30 - 40 s than the fuel quantity which is re-...
  • Page 111 Driving through water Driving off paved roads  Read and observe on page 107 first. Fig. 96 Maximum permissible water lev- Only drive on such roads and in such terrain, which match the vehicle parame- el when driving through water ters »...
  • Page 112: Assist Systems

     Read and observe on page 109 first. Assist systems The ESC improves vehicle stability in dynamic driving situations, such as when Braking and stabilisation systems the vehicle starts to skid. The ESC monitors whether the desired direction of the current vehicle motion ...
  • Page 113: Parking Aid

    The HHC is active from a 5% slope if the driver's door is closed. HHC is only ev- Note er active on slopes when in forward or reverse start off. For vehicles without stabilization control (ESC), during a TCS intervention the control indicator in the instrument cluster flashes.
  • Page 114: Cruise Control System

    Note Function For vehicles with a factory-fitted towing device, the system cannot be activa- ted when towing a trailer. Cruise Control System  Introduction This chapter contains information on the following subjects: Functioning Operating Description Fig. 98 Location of the sensors / range of the sensors The Cruise Control System (CCS) maintains a set speed without you having to actuate the accelerator pedal.
  • Page 115: Start-Stop

    WARNING WARNING If the engine power and engine braking effect is insufficient to maintain Always deactivate the cruise control system after use to prevent the sys- ■ the set speed, vehicle operation must be taken over! tem being switched on unintentionally. Control may only be resumed if the stored speed is not too high for the ■...
  • Page 116 Note Operating conditions of the system If the vehicle remains outdoors for a long time in minus temperatures or in ■ direct sunlight, it can take several hours until the internal temperature of the Fig. 100 vehicle battery reaches a suitable temperature for proper operation of the MAXI DOT display: Engine is au- START STOP system.
  • Page 117 Automatic engine shutdown takes place, segment display shows START-STOP Manually deactivating/activating the system ACTIVE or the MAXI DOT display shows the warning sign  » Fig. 100 page 113. Fig. 101 Automatic engine start Button for the START-STOP sys- › Release the brake pedal.
  • Page 118: Tyre Pressure Monitoring

    » page 149. The tyre pressure values are to be saved every 10,000 km or once annually to The system cannot warn in case of very rapid tyre inflation pressure loss, ■ ensure correct system functioning. e.g. in case of sudden tyre damage.
  • Page 119: Hitch And Trailer

    Hitch and trailer Description Hitch  Introduction This chapter contains information on the following subjects: Description Adjusting the ready position A correctly set ready position Assembling the bar ball - Step 1 Assembling the bar ball - Step 2 Fig. 103 Carrier for the towing device/tow bar Check proper fitting ...
  • Page 120 The hand wheel remains locked in this position. Adjusting the ready position WARNING If the tow bar cannot be correctly placed in the ready position, then it must not be used. A correctly set ready position Fig. 104 Remove cap from the lock / insert key into the lock Fig.
  • Page 121 Assembling the bar ball - Step 1 Assembling the bar ball - Step 2 Fig. 108 Secure the lock and remove key / place cap on lock Fig. 107 Remove cap for receiving shaft / use ball bar   Read and observe on page 116 first.
  • Page 122 Check proper fitting Fig. 111 Unlock lock Fig. 109 Correctly secured ball head  Read and observe on page 116 first. ›  Read and observe on page 116 first. Remove the cover from the lock in the direction of the arrow »...
  • Page 123 › Grasp the ball bar from below » Fig. 112. Accessories › Pull the hand wheel in the direction of the arrow › Turn the hand wheel in the direction of the arrow to the stop, and hold in Fig. 113 this position.
  • Page 124: Trailer

    If the trailer that is to be towed has a 7-pin connector, you can use a suitable Note adapter from ŠKODA Original Accessories to establish a connection to the elec- We recommend that you use accessories from ŠKODA Original Accessories. tricity.
  • Page 125 Loading a trailer Towing a trailer The vehicle/trailer combination must be balanced, whereby the maximum per- Driving speed missible drawbar load must be utilised. If the drawbar load is too low, it jeop- For safety reasons, do not drive faster than 80 km/h when towing a trailer. ardises the performance of the vehicle/trailer combination.
  • Page 126 Conditions for including a trailer in the anti-theft alarm system. The vehicle is factory-fitted with an anti-theft alarm system and towing  device. The trailer is electrically connected to the towing vehicle via the trailer  socket. The electrical system of the vehicle and trailer is functional. ...
  • Page 127: General Maintenance

    For the sake of the environment General Maintenance Technical documents regarding alterations carried out on the vehicle must be kept by the vehicle user in order to be handed over to the recyclers at a later Care and maintenance date. This ensures that the vehicle is recycled in an environmentally sound manner.
  • Page 128 The ŠKODA Service Partners are up-to-date on the legally required tests and ŠKODA AUTO a.s. is able to vouch for the safety, suitability and long service life will prepare the vehicle for the tests as part of a service operation if required, of these products.
  • Page 129 ŠKODA Service Partners are liable for any defects of ŠKODA Genuine Accesso- Airbags ries for a period of 2 years after installation or delivery in accordance with the  materials defect liability, unless agreed otherwise in the purchase agreement Read and observe on page 124 first.
  • Page 130: Washing Vehicle

    WARNING Acceptance and recycling of used vehicles When washing your vehicle in the winter: Water and ice in the braking sys-  Read and observe on page 124 first. tem can affect the braking efficiency – risk of accident! ŠKODA meets the requirements of the brand and its products with regard to CAUTION protecting the environment and the preserving resources.
  • Page 131: Cleaning Vehicle Exterior

    Automatic car wash systems Cleaning vehicle exterior  Read and observe on page 127 first.  Introduction The usual precautionary measures must be taken before washing the vehicle This chapter contains information on the following subjects: in an automatic car wash system (e.g. closing the windows and the sliding/tilt- Vehicle paint work ing roof etc.).
  • Page 132: Vehicle Paint Work

    For the sake of the environment Plastic parts Used vehicle care product cans represent hazardous waste that is harmful to  Read and observe on page 128 first. the environment. These must be disposed of in accordance with national legal regulations.
  • Page 133: Decorative Films

    Cleaning windows Decorative films Regularly clean windows from the inside with clean water.  Read and observe on page 128 first. Dry the glass surfaces with a clean chamois leather or a cloth intended for this purpose. Wash the films with a mild soap solution and clean, warm water. CAUTION The following instructions must be followed when washing the vehicle with a high-pressure cleaner.
  • Page 134: Door Closing Cylinder

    Regularly remove salt and brake abrasion, otherwise the rim material will be Door closing cylinder corroded.  Read and observe on page 128 first. Light alloy wheels After washing thoroughly and treat the wheel rims with a protective product Specific products must be used for de-icing door lock cylinders. for light alloy wheels.
  • Page 135: Interior Care

    We recommend having the protective coating underneath the vehicle and the WARNING chassis checked — preferably before the beginning of winter and at the end of Vehicle care products may be harmful to your health if not used according ■ winter.
  • Page 136 Dust and dirt in pores and creases cause abrasions on the surface and lead to ® Artificial leather, materials and Alcantara premature embrittlement of the leather surface. Therefore, they must be re-  moved regularly at short intervals with a cloth or vacuum cleaner. Read and observe on page 132 first.
  • Page 137: Inspecting And Replenishing

    Seat covers Inspecting and replenishing  Read and observe on page 132 first. Fuel Electrically heated seats  Introduction Use a specific cleaning agent such as dry foam or similar to clean the cov- ers. » This chapter contains information on the following subjects: Seats without seat heating Refuelling Thoroughly vacuum the seat covers with a vacuum cleaner before cleaning.
  • Page 138 WARNING Refuelling Do not smoke when refuelling and do not use a mobile phone. ■ The fuel and fuel vapours are explosive - it can be fatal! ■ Observe the local regulations regarding fuel handling. ■ WARNING Instructions for filling the reserve canister Never fill the reserve can inside the vehicle.
  • Page 139 Required fuel - unleaded petrol 95/91 or 92 or 93 RON CAUTION Use unleaded fuel with the octane rating 95 RON. Unleaded petrol with the If, in an emergency, the vehicle has to be refuelled with petrol of a lower oc- ■...
  • Page 140: Engine Compartment

    All diesel engines can be operated using diesel fuel with at most 7% biodiesel Engine compartment (B7)  Introduction Operation in winter – Winter-grade diesel fuel In the cold season, only use “winter-grade diesel fuel” which will still operate This chapter contains information on the following subjects: properly even at a temperature of -20 °C.
  • Page 141 WARNING Note Information for working in the engine compartment with the engine run- Please consult a specialist garage for any questions relating to fluids. ■ ning Fluids with the proper specifications can be purchased from the ŠKODA Origi- ■ nal Accessories or from the ŠKODA Genuine Parts ranges. Pay particular attention to moving engine parts, e.g.
  • Page 142 ›  Grasp the bonnet catch and lift in the direction of arrow Read and observe on page 137 first. › Remove the lid prop in the direction of arrow from the holder. › Arrangement in the engine compartment » Fig. 118 Secure the open flap inserting the end of the post into the opening in the di- Coolant expansion reservoir rection of arrow...
  • Page 143: Engine Oil

    The cleaning fluid is provided for the cleaning of the front and rear window as The engine oils are undergoing continuous further development. Thus the in- well as the headlight. formation stated in this Owner's Manual is only correct at the time of publica- tion.
  • Page 144  Read and observe on page 140 first. Diesel engine Specification 1.6 l/66, 77 kW TDI CR VW 507 00 The dipstick indicates the engine oil level . Engine oil VW 505 01 can optionally be used in diesel engines without a DPF. Dipstick »...
  • Page 145: Coolant

    WARNING (Continued) Replenishing When opening the end cover of the coolant expansion reservoir, cover it ■  Read and observe on page 140 first. with a cloth to protect your face, hands and arms from hot steam or hot coolant. ›...
  • Page 146: Brake Fluid

    Checking the coolant level Replenishing  Read and observe on page 142 first. Fig. 121 Coolant expansion reservoir The coolant expansion tank must always contain a small amount of cool- » page 142, in section Introduction. › Place a cloth over the cap of the coolant expansion tank and unscrew the cap carefully.
  • Page 147: Vehicle Battery

    Note Specification The brake fluid is changed as part of a compulsory inspection service. ■  Read and observe on page 143 first. We recommend using brake fluids from the ŠKODA Original Accessories ■ range. The brake fluid must comply with the following standards or specifications: ›...
  • Page 148 If the vehicle has not been driven for more than 3 to 4 weeks, the battery will WARNING ■ discharge. Prevent the battery from discharging by disconnecting the battery's There is risk of injuries, poisoning, chemical burns, explosions or fire when negative terminal ...
  • Page 149 Note Checking the battery electrolyte level The battery acid level is also checked regularly by a specialist garage as part ■ of the inspection service. Fig. 124 For technical reasons, on vehicles with the description “AGM”, the electrolyte ■ Electrolyte level indicator level cannot be checked.
  • Page 150 › First, disconnect the negative terminal  first, then the positive terminal WARNING  of the battery. When you charge a battery, hydrogen is released, and a highly explosive ■ gas mixture is also produced. An explosion can be caused through sparkling Connecting ›...
  • Page 151: Wheels

    CAUTION Wheels Despite such intervention by the vehicle electric system management, the ■ vehicle battery may be drained. For example, when the ignition is switched on Tyres and wheel rims a long time with the engine turned off or the side or parking lights are turned on during longer parking.
  • Page 152 Always fit the tyres with the deeper tread depth to the front wheels. Sticker with prescribed tyre inflation pressure values » Fig. 125 Position of the CNG label Tyre storage Identify disassembled tyres so that the previous direction of rotation can be Inflation pressure for half load maintained if the tyres are reassembled.
  • Page 153  Attention to the following notes may affect tyre wear. Read and observe on page 148 first. Driving style Wear indicators Fast cornering, sharp acceleration and braking increase the wear of your tyres. The base of the tread of the tyres contains has a 1.6 mm high wear indica- »...
  • Page 154: Manufacturer-Approved Tyre Variants

    Rapid Green tec Speed symbol Approved tyre variants are first to be selected for the model variant (e.g. Rapid The maximum speed symbol indicates the maximum permissible vehicle speed GreenLine), and then selected according to the engine size of your vehicle.
  • Page 155: Winter Operation

    Load index Speed symbol Not valid for the following markets: Armenia, Azerbaijan, Belarus, Georgia, Kazakhstan, Kyrgyzstan, Mol- dova, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan. 175/70 R14 185/60 R15 Rapid Green Line 1.2 l./55 kW MPI 215/45 R16 Tyre Minimal Minimal...
  • Page 156: Fig

    Remove the full wheel trims before installing the snow chains » page 157. Winter tyres WARNING Summer tyres have less grip on ice, snow and at temperatures below 7 °C. This Observe the national legal regulations relating to the use of snow chains. is especially true of vehicles fitted with wide tyres or high-speed tyres.
  • Page 157: Do-It-Yourself

    WARNING Do-it-yourself The first-aid kit and warning triangle must always be secured safely so that they do not come loose when making an emergency braking or in a vehicle Emergency equipment and self-help collision which could cause injuries to occupants. Emergency equipment Note ...
  • Page 158: Reserve And Temporary Spare Wheel

    › Remove the fire extinguisher. Depending on the equipment, not all the components listed in the on-board › For mounting, fit the fire extinguisher back into the holder and secure it with tool kit have to be contained in it. straps.
  • Page 159: Changing A Wheel

    › Screw on the nut in the opposite direction to the arrow » Fig. 131 until the WARNING wheel is safely secured. If, in the case of puncture occurring, the spare tyre with a non-bound di- ■ › Place the box with the tool kit back into the spare wheel and secure it with rection or an opposite direction of rotation must be mounted, then drive the tape.
  • Page 160 Raising the vehicle Installing › Press the wheel trim onto the wheel rim at the designated valve open- Anti-theft wheel bolts » For your own safety and the safety of the passengers, the following instruc- › Then press the trim into the wheel rim until its entire circumference locks tions must be observed before changing a wheel on the road.
  • Page 161 › Installing Have the tightening torque of the wheel bolts checked with a torque › Push the cap onto the wheel bolt up to the stop. wrench as soon as possible. After changing the wheel, the tyre pressure should be adjusted. In vehicles Changing a wheel with tyre pressure monitoring, tyre pressure values are to be stored »...
  • Page 162 › Grasp the end of the wrench and turn the bolt about one turn in the direction In order to raise the vehicle, the jack from the tool kit is to be used. of the arrow » Fig. 133. Position the car jack at the jacking point closest to the flat tyre . Tightening The mounting points are located on the metal bar of the lower sill on the un- ›...
  • Page 163: Puncture Set

    Anti-theft wheel bolts Puncture set  Introduction Fig. 136 Principle sketch: Anti-theft This chapter contains information on the following subjects: wheel bolt with adapter Components of the puncture repair kits General information Preparations for using the breakdown kit Sealing and inflating the tyre Notes for driving with tyre repaired Use the breakdown kit to reliably repair tyre damage caused by foreign bodies The anti-theft wheel bolts protect the wheels from theft.
  • Page 164 Components of the puncture repair kits General information  Read and observe on page 160 first. For your own safety and the safety of your passengers, the following instruc- tions must be observed before carrying out a wheel repair on the road. Switch on the hazard warning lights system.
  • Page 165: Jump-Starting

    › Use the valve remover to unscrew the valve core and place it on a clean WARNING surface (rag, paper, etc.). If you cannot inflate the tyre to at least 2.0 bar, this means the damage ■ sustained was too serious. The sealing agent cannot be used to seal the Sealing and inflating the tyre tyre.
  • Page 166  The battery of another vehicle can be used to jump-start your vehicle if the en- Read and observe on page 163 first. gine will not start because the battery is flat. The starting process using the battery of another vehicle requires the use of WARNING jumper cables.
  • Page 167: Towing The Vehicle

    Vehicles with automatic transmission may be towed in with a tow bar or a tow WARNING rope or with the front wheels raised. If the vehicle is raised at rear, the auto- Do not clamp the jump-start cable to the negative terminal of the dis- ■...
  • Page 168 The cap must engage firmly. CAUTION Do not tow start the engine – there is a risk of damaging the engine and the ■ Removing/installing the towing eye › catalytic converter. The battery from another vehicle can be used as a jump- Manually screw the towing eye as far as it will go in the direction of the ar- start aid »...
  • Page 169: Remote Control

    › Press off the battery cover » Fig. 143 with your thumb or using a flat CAUTION screwdriver in the region of the arrows The detachable ball rod and/or the vehicle can be damaged if an unsuitable › Remove the discharged battery from the key by pressing the battery down in tow bar is used.
  • Page 170: Replacing Windscreen Wiper Blades

    Locking the door without a locking cylinder Selector lever-emergency unlocking Fig. 144 Emergency locking: Left/right rear door Fig. 146 Selector lever-emergency unlocking › An emergency locking mechanism is located on the face side of the doors Firmly apply the handbrake. ›...
  • Page 171 Replacing the windscreen wiper blades Replacing the rear window wiper blade Fig. 147 Windscreen wiper blade Fig. 148 Rear window wiper blade   Read and observe on page 167 first. Read and observe on page 167 first. Before replacing the windscreen wiper blade, put the windscreen wiper arms Removing the wiper blade ›...
  • Page 172: Fuses And Light Bulbs

    CAUTION Fuses and light bulbs “Never repair” fuses, and do not replace them with fuses of a higher amper- ■ age – risk of fire! This may also cause damage at other points in the electrical Fuses system.  A blown fuses is recognisable by the molten metal strip. Replace the faulty Introduction ■...
  • Page 173 Power consumer Assignment of the fuses in the dash panel Power steering, speed sensor, engine control unit, control unit for fuel pump Daytime running lights/radio for vehicles with START-STOP Mirror heater Ignition lock input Engine control unit, electronic control unit for fuel pump, fuel pump Reversing lamp (automatic gearbox), fog lights with the function CORNER Operating controls for the heating, electronic control unit for air con-...
  • Page 174  Read and observe on page 169 first. Power consumer Horn Replacing fuses › Windscreen wipers Press together the interlocks of the cover simultaneously in the direction of the arrow » Fig. 151. Boot lid lock, central locking system › Remove the cover in the direction of the arrow Alarm ›...
  • Page 175: Replacing Bulbs

    Note Replacing bulbs This Owner's Manual only describes the replacement of bulbs where it is pos- ■  Introduction sible to replace the bulbs on your own without any complications arising. Other bulbs must be replaced by a specialist garage. This chapter contains information on the following subjects: We recommend that a box of replacement bulbs always be carried in the ve- ■...
  • Page 176: Replacing The High Beam Bulb (Halogen Headlights)

    Replacing the high beam bulb (halogen headlights) Fig. 156 Change the light bulb for the parking light Fig. 154 Changing the bulb for the low beam  Read and observe on page 172 first.  Read and observe on page 172 first. Removing/replacing the bulb for main beam and separate daytime running lights ›...
  • Page 177: Changing The Front Turn Signal Bulb

    Changing the front turn signal bulb Replacing the bulb for the fog light Fig. 157 Changing the bulb for the front turn signal light  Read and observe on page 172 first. › Turn the socket with the bulb in the direction of arrow »...
  • Page 178: Replacing The Bulb For The Licence Plate Light

    › Attach the connector. Rear Light Refit the headlight and grille › Replace the fog light by inserting it in the opposite direction of the arrow » Fig. 158 and tightening. › Insert the protective grille and carefully press it in. The protective grille must engage firmly.
  • Page 179: Replacing Bulbs In Rear Light

    › › Carefully push the cover in » Insert the bulb holder in the tail lamp assembly. › Screw the tail lamp into place and install the cover. The lamp holder must engage firmly. The cover must engage securely. CAUTION Ensure that the cable bundle does not become pinched between the body ■...
  • Page 180: Technical Data

    The vehicle data sticker contains the following data. Technical data Vehicle identification number (VIN) Technical data Vehicle type Gearbox code/paint number/interior equipment/engine output/engine Vehicle data code Partial vehicle description  Introduction Type plate This chapter contains information on the following subjects: The type plate »...
  • Page 181 The calculation of the combined fuel consumption considers a weighting of Operating weight and payload about 37 % for the intra-urban cycle and 63 % for the extra-urban cycle. Operating weight Note This value represents the minimum operating weight without additional The fuel consumption and emission levels given on the ŠKODA websites or in weight-increasing equipment such as air conditioning system, spare wheel, or ■...
  • Page 182 Dimensions Fig. 163 Principle sketch: Vehicle dimensions Vehicle dimensions for operating weight without driver (in mm) » Fig. 163 Specification Value Basic dimension 1461/1488 Height Vehicles with an off-road package. 1474/1500 Basic dimension 1457 Front track For vehicles fitted with the 1.2 l/55 kW MPI and 1.2 l/63 kW TSI engines and 14" 1463 wheel rims.
  • Page 183 Angle Fig. 164 Principle sketch: Departure an- Angle » Fig. 164 Overhang angle, front Overhang angle, rear Departure angle The values shown indicate the maximum incline of an embankment, up which the vehicle can drive at a slow speed without collision of the bumper or under- body.
  • Page 184 Vehicle-specific details per engine type The specified values have been determined in accordance with rules and under conditions set out by legal or technical requirements for determining operational and technical data for motor vehicles. 1.2 l/55 kW MPI engine Output (kW at rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm 55/5400...
  • Page 185 1.2 ltr./77 kW TSI engine Output (kW at rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm 77/5000 175/1550-4100 4/1197 Performance and Weights Top speed (km/h) Acceleration 0 - 100 km/h (s) 10.3 Operating weight - minimal (kg) 1175 Increases up to 12 % 1100 Permissible trailer load, braked (kg)
  • Page 186 1.6 l/77 kW MPI engine Output (kW at rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm 77/5600 153/3800 4/1598 Performance and Weights Top speed (km/h) Acceleration 0 - 100 km/h (s) 10.6 11.9 Operating weight - minimal (kg) 1155 1195 Increases up to 12 %...
  • Page 187 1.6 ltr./77 kW TDI CR engine Output (kW at rpm) Maximum torque (Nm at rpm) Number of cylinders/displacement (cm 77/4400 250/1500-2500 4/1598 Performance and Weights Top speed (km/h) Acceleration 0 - 100 km/h (s) 10.4 Operating weight - minimal (kg) 1265 Increases up to 12 % 1200...
  • Page 188: Index

    Air outlet vents Automatic gearbox Index Manual shifting of gears Alarm Selector lever-emergency unlocking Switching off Selector lever lock Triggering Starting-off and driving abroad Alcantara Tiptronic lead-free petrol cleaning Using the selector lever Abroad Anti-theft alarm system Headlights Automatic gearbox modes Activating/deactivating Automatic load deactivation Trailer...
  • Page 189 Brake Change Cleaning information messages Engine oil Alcantara warning light light bulb in tail light and maintaining belts artificial leather Brake booster Changing headlight glasses bulbs brake fluid materials Front turn signal bulb specification natural leather Wheels Brake fluid plastic parts Changing a wheel Checking seats covers of the electrically heated seats...
  • Page 190 Clothes hook Emergency locking Opening Cockpit DAY LIGHT Warning light door open 12-Volt power outlet See Daytime running lights Ashtray Door open Daytime running lights Cigarette lighter Warning light De-icing General view Double-sided floor covering windows Lights Driving storage compartments Deactivating an airbag Driving through water useful equipment...
  • Page 191 Emergency equipment Fog lights Generator Fire extinguisher Warning light Indicator light First-aid kit Fog lights with CORNER function Genuine parts Jack Footmats Glasses compartment Reflective Vest see footmats Glow plug system Vehicle tool kit Force limit Warning light Warning triangle Power windows emergency wheel Front airbag...
  • Page 192 Hazard warning light system Headlight flasher Ice scrapers Jack Indicator lights Maintenance Ignition Low beam Jacking points Main beam Ignition lock Raise vehicle Parking light Immobilizer Jump-starting 162, 163 Rear fog light Indicator lights Replacing bulbs Individual settings switching on/off Locking Turn signal Unlocking...
  • Page 193 Manual air conditioning Passive safety Air distribution control Before setting off Operating elements Driving safety Nameplate Safety equipment Manual gear changing Navigation system see gear changing Passive Safety Nets MAXI DOT Payload See MAXI DOT display Notes for driving with tyre repaired Pedals MAXI DOT display Notes on using wheels...
  • Page 194 Refuelling Setting Fuel seats and head restraints SAFE Remote control Setting the See Safe securing system Locking Side airbag SAFELOCK Replacing the battery SmartGate See Safe securing system Synchronisation process connection Safe securing system Unlocking Password Safety Remote control key Settings Child safety Replacing the battery...
  • Page 195 Storage compartment Trailer Glasses compartment 13-pin socket Under-body in the boot connection and disconnection Vehicle care in the centre console Loading Under-body protection in the front arm rest Safety eye on the front passenger side Towing a trailer Unlock Storage compartments Trailer operation Unlocking Storage pockets on the front seats...
  • Page 196 Cavity protection Washing Window Cleaning vehicle exterior Automatic car wash system Interior mirror Cleaning wheels by hand Window wiper Decorative films High-pressure cleaner Replacing the rear window wiper blade Door locking cylinder Washing vehicles Windscreen washer fluid Headlight glasses Waste container Checking Interior care Replenishing...
  • Page 197 Index...
  • Page 198 Reprinting, reproduction, translation, or any other use, either in whole or in Issued by: ŠKODA AUTO a.s. part, is not permitted without the written consent of ŠKODA AUTO a.s.. © ŠKODA AUTO a.s. 2014 ŠKODA AUTO a.s. expressly reserves all rights relating to copyright laws. Subject to change.
  • Page 200 Also please pay attention to those parts in the Owner's Manual that are marked below. Work with us – for the sake of the environment. Návod k obsluze Rapid anglicky 11.2014 S56.5610.09.20 5JA012720AF  5JA012720AF...

Table of Contents