Samsung SVR-440 User Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. DVR
  5. SVR-440
  6. User manual

Samsung SVR-440 User Manual

Digital video recorder
Hide thumbs Also See for SVR-440:
Table of Contents

Advertisement

Quick Links

1

Advertisement

Table of Contents
loading

Related Manuals for Samsung SVR-440

Summary of Contents for Samsung SVR-440

  • Page 2 Introduction Thank you for purchasing the SVR440 This user manual is for the SVR-440. The term “unit” always refers to the SVR-440. We recommend users who install and operate the unit to thoroughly read this manual and other reference manuals indicated in this manual before installation and operation.
  • Page 3 Warning Marks Warnings and Cautions – the marks that give warning to users in this manual indicate different levels of importance. These marks are classified by the level and potentiality of risk. It is strongly recommended for users to completely understand these marks before using the unit. This warning is given where carrying out an instruction can cause serious risk of injury or death if the unit is not properly handled or operated.

  • Page 4: Table Of Contents

    Table of contents CHAPTER 1 SAFETY CAUTIONS..............7 CHAPTER 2 OVERVIEW ................9 2.1 Features ..............................9 2.2 Configuration............................11 2.3 Names and Functions of Each Part....................12 2.3.1 Control Panel on the front ......................12 2.3.2 Rear Connection Terminals ......................14 2.3.3 Remote Controller .........................15 2.4 Unit Specification ..........................16 CHAPTER 3 HOW TO INSTALL..............
  • Page 5 4.5 RECORD SETUP..........................38 4.5.1 REPEAT RECORD ........................38 4.5.2 RECORD SETUP..........................39 4.5.3 CH1~CH4...........................39 4.6 SYSTEM SETUP..........................41 4.6.1 HDD FORMAT..........................41 4.6.2 PASSWORD ..........................41 4.6.3 CLOCK ............................42 4.6.4 ETC(LANGUAGE SETTING) .....................42 4.7 NETWORK & SERIAL SETUP.......................43 4.7.1 NETWORK ...........................43 4.7.2 CLIENT ACCESS.........................50 4.7.3 SEND E-MAIL..........................50 4.7.4 RS-485/422............................51 4.8 EVENT SETUP ..........................51 4.8.1 MOTION DETECTTION ......................52...
  • Page 6 5.4 Recording ............................59 5.4.1 General Recording.........................59 5.4.2 Scheduled Recording........................59 5.5 Recorded Video Search........................59 5.5.1 EVENT SEARCH .........................60 5.5.2 TIME LINE BAR ..........................60 5.5.3 GO TO............................61 5.5.4 GO FIRST .............................61 5.5.5 GO LAST ............................61 5.5.6 LOG FILE LIST ..........................61 5.5.7 COPY LIST ...........................62 5.6 Recorded File Playback ........................64 5.7 PTZ ..............................64 5.7.1 PAN/TILT adjustment........................64...

  • Page 7: Chapter 1 Safety Cautions

    Chapter 1 Safety Cautions * Before Installation – On the rear of the unit, ensure accurate setting of supply voltage prior to power connection. – Disconnect the power before installation. – Do not install the unit in humid locations. It may result in a risk of electrical shock or fire. –...

  • Page 8: Fcc Compliance Statement

    – Do not move the unit while it is in use. – Do not apply strong force or throw the unit. SAMSUNG/Western Digital/Maxtor HDD(7200RPM / EIDE Type)If you add – We recommend using other HDDs, the system may cause abnormal operations. Thus, please contact your local vendor before adding a HDD.

  • Page 9: Chapter 2 Overview

    . Pan &Tilt control Recording The Samsung SVR-440 can record up to 120 frames per second. It also records events on an event list as well as provides the pre-event recording function. . Simultaneous execution of three functions: recording, playback, and networking .
  • Page 10 Model : LTR-52327SX Network The Samsung SVR-440 supports a wide range of networks such as LAN and ADSL, DHCP. The user can also easily operate and manage main functions of the unit from a remote place using the exclusive PC viewer.

  • Page 11: Configuration

    2.2 Configuration The SVR-440 package contains the main unit and its components as specified below. When you purchase the unit, please check to ensure the components specified below are included. If any components are missing, please contact your local vendor.

  • Page 12: Names And Functions Of Each Part

    2.3 Names and Functions of Each Part 2.3.1 Control Panel on the front Indication LED LED Name Description Power Light up when power is applied to the system Light up when the system is accessing HDD EVENT Light up when sensor is triggered or Motion is detected NETWORK Light up when client has connected to the system through the network...
  • Page 13 Press to move right in Menu item in setup mode and to select camera2 in live mode. It can also be used to enter number 2 when entering password. Press to move down in Menu item in setup mode and to select camera3 in live mode.

  • Page 14: Rear Connection Terminals

    2.3.2 Rear Connection Terminals ① ⑨ ⑫ ④ ⑬ ⑤ ⑦ ② ③ ⑧ ⑥ ⑩ ⑪ ① Video in : Camera Input(NTSC/PAL) ② Video out : Composite Video Output ③ VGA : VGA output for PC monitor ④ RS-232 ⑤...

  • Page 15: Remote Controller

    2.3.3 Remote Controller RECORD Start/Stop Recording PTZ Control Button SEARCH Search Button AUTO Auto Sequence button Select and Save the changed value in ENTER Menu MENU Enter into Setup Menu Return to previous Menu Jump backward. Playback position moves F/REW to 1 minute backward.

  • Page 16: Unit Specification

    2.4 Unit Specification ■ System Items Specification Processor Operating System(O/S) RTOS Compression method MPEG-4 ■ Video Items Specification Input Method Composite Input 4-Channel Video Input Level 1.0 Vp-p, Composite Live Screen Display Speed NTSC: 120 Frames/Sec PAL: 100 Frames/Sec Live Screen Digital Memory NTSC: 720 (W) 480 (H) Pixels for the full screen.
  • Page 17 ■ Remote Control Items Specification Infrared LED Up to 5m ■ Recording Items Specification Maximum Number of Frames/Sec NTSC(720X480): 30 Frames/Sec (Resolution) NTSC(360X240): 120 Frames/Sec PAL(720X576): 25 Frames/Sec PAL(360X288): 100 Frames/Sec Recording Method 3 Types of Recording Modes: General, Schedule, Event Pre-Event Recording Channel ON/OFF Setting Image Quality...
  • Page 18 ■ HDD Items Specification Basic Supply HDD Type EIDE Minimum Rate 7200rpm Western Digital/Samsung Electronics/Maxtor Recommended units We recommend the models described below among Western Digital/Samsung Electronics/ Maxtor HDD series. Model HDD Capacity Buffer Western Digital WD1600BB-22GRA0 160GB WD2000BB-00GUA0 200GB...
  • Page 19 ■ Password Items Specification 2 stage Password 4-digit Password(including four numbers) Adimin : Control all function(Default is 1111) Network: : Network access (Default is 1111) ■ Network Items Specification General Live Screen: Monitoring Playback Screen: Search Menu Setting: Menu setting available(CMS S/W : option) Access Method: Dedicated Viewer Protocol: TCP/IP, DHCP Interface: Ethernet(10/100Mbps), ADSL...
  • Page 20 ■ Exterior Items Specification Material Steel Case Dimension 260(W) X 350(D) X 65(H)mm Weight About 4.5Kg ■ Connection Terminals Items Specification Video Input BNC(4) Monitor Output BNC(1) VGA Output(PC Monitor) 15-Pin DSUB Audio Jack RCA Input(4), RCA Output(1) USB Port USB2.0(Firmware Upgrade/Copy) 9-Pin DSUB RS-232C(Standby)

  • Page 21: Chapter 3 How To Install

    Chapter 3 How to Install 3.1 How to Connect All Parts The connection layout for the SVR-440, the monitor, CCTV and external devices are described below. 상세 연결 3.2.1 착탈식 하드디스크 랙 장착 방법...

  • Page 22: Detailed Connection

    3.2 Detailed Connection 3.2.1 Camera SVR-440 can accommodate up to 4 cameras for CCTV. Connect the BNC terminal of each camera to the CAMERA IN terminal of the unit. 3.2.2 Audio The Samsung SVR-440 can save audio information. For storage or output of audio information, it is required to connect the relevant devices.

  • Page 23: Monitor

    Audio Output Connect the RCA Audio Output Terminal (monitor with a speaker, etc.) to the AUDIO OUT terminal on the rear of the unit. 3.2.3 Monitor Connect the VIDEO OUT terminal of the MONITOR OUTPUT and the BNC terminal of the monitor There is also VGA video output for using the BNC cable for video data output to the main monitor.

  • Page 24: External Connector

    3.2.4 External Connector Alarm Input (ALARM IN) This external sensor connection terminal transfers data from the connected sensor or device to the unit. Relay Output (RELAY OUT) This Alarm Output terminal uses the contact relay for the alarm output to the external devices. You can select NO (Normal Open), CM (Common) or NC (Normal Close) for connection according to the contact point status.
  • Page 25 External Control Device Terminal(RS–422/485) This terminal is connected to external control devices. The JP2 termination that set is turns on and off the termination resistance of RS–422/485 communication device. The JP2 termination is inside of the DVR. Description Classification RS-422 RS-485 TX+(+Transmit Data) Data+...
  • Page 26 LAN Connection (Ethernet 10/100 Base–T) This port is to connect to a network. Description Description TX+(Transmit Data) N/C(No connection) TX-(Transmit Data) RX-(Receive Data) RX+(Transmit Data) N/C(No connection) N/C(No connection) N/C(No connection)
  • Page 27 Monitor Output(VGA) This is the output connector for VGA Monitor. Description Description Red Signa(75, 0.7Vp–p) N/C(No connection) Green Signal(75, 0.7Vp–p) Ground Blue Signal(75, 0.7Vp–p) Ground N/C(No connection) N/C(No connection) Ground HSYNC (Horizontal Synchronization) Ground VSYNC(Vertical Synchronization) Ground N/C(No connection) Ground...

  • Page 28: Chapter 4 How To Set

    Chapter 4 How to Set 4.1 Menu Configuration Press the Menu button on the front side of the unit or the button on the remote control, and the MENU menu for a variety of settings related to the unit will appear. The menu is configured as described below.
  • Page 29 The menu is configured as illustrated below. Main Menu Submenu Setup Subjects Screen CH1~4 Title, Brightness, Contrast Auto S quence Sequence, Sequence Dwell, Video Loss Skip OSD, Clock Display, HDD Free Space, Recording Status, Status Title Display, Event Display, OSD Contrast Repeat Record, Warning Massage, Warning Beep Record Repeat...
  • Page 30 Network Type, ADDRESS, SUBNET MASK, Network Network GATEWAY, DNS, ID, PW, DDNS SERVER DONAMAIN ADDRESS PORT, CLIENT ACCESS, BANDWIDTH SAVING Client Access E-mail, Mail Address, Mail Server IP E-Mail System ID, BAUD RATE, DATA BIT, PARITY BIT, RS-485/422 STOP BIT Event Motion Detect CH1~4 Motion Zone, CH1~4 Motion Sensitivity...

  • Page 31: Default Setup

    4.2 Default Setup The SVR-440 is delivered to customers with the factory default values as described below. To initialize the menu setup to the factory default values, select [YES] for the [DEFAULT] item in [SYSTEM SETUP]–[ETC] on the menu. Then, all setting values changed by users are initialized to the default values as illustrated below.
  • Page 32 MODE CONTINUOUS QUALITY HIGH FRAME RATE 1f/s AUDIO POST RECORD TIME 5SEC PRE RECORD 5SEC RELAY OUT EVENT BEEP SCHEDULE SETUP MODE CONTINUOUS QUALITY HIGH FRAME RATE 1f/s AUDIO POST RECORD TIME 5SEC PRE RECORD 5SEC RELAY OUT EVENT BEEP SCHEDULE SETUP MODE...
  • Page 33 LANGUAGE ENGLISH KEY BUZZER DEFAULT SETUP DESCRIPTION DISPLAY REMOTE CONTROLLER ID ■ NETWORK Main Menu Submenu Default NETWORK NETWORK TYPE IP ADDRESS 000.000.000.000 SUBNET MASK 000.000.000.000 GATEWAY 000.000.000.000 000.000.000.000 DDNS SERVE DDNS SERVER DOMAIN ADDRESS ns.standalone4ch.com CLIENT ACCESS PORT 3495 CLIENT ACCESS BANDWIDTH SAVING E-MAIL...

  • Page 34: Menu Screen Setup

    SENSOR4 TYPE ■ PTZ SETUP Main Menu Submenu Default PTZ CAMERA ID MODEL NONE PTZ CAMERA ID MODEL NONE PTZ CAMERA ID MODEL NONE PTZ CAMERA ID MODEL NONE 4.3 Menu Screen Setup Select the button on the remote control or the main unit, and the following Menu Screen MENU appears.

  • Page 35: Screen Setup

    . Setup Items: Change the settings on the Submenu. . How to Set: This message provides the guide for menu setup. . It may take a little while for the recording setup. Then, please wait for a while. . Except for the recording setup, setting changes are immediately applied. Operations * Operation the unit using the buttons on the main unit.

  • Page 36: Ch1~Ch4

    4.4.1 CH1~CH4 Select setup items related to channels such as channel titles or brightness. . Channel Titles: Titles can be individually set to each channel. Select the channel title and press ENT button . Then, the keyboard to enter the title is displayed as illustrated below. The positions of characters in the Channel Titles can be arranged by using buttons - After moving the cursor, is moved, press the ENT button to select the relevant character.

  • Page 37: Auto Sequence

    4.4.2 AUTO SEQUENCE <CH1 -> CH2 -> CH3 -> CH4 > The live screens are automatically switched in the order of at the predefined switching interval. The channel switching interval can be set from 1 up to 10 on the [SEQUENCE] menu. .

  • Page 38: Record Setup

    recording is indicated. . RECORD STATUS [ON/OFF]: With Record Status [ON], the recording status “S” is displayed on the corner of the screen during recording. . TITLE DISPLAY [ON/OFF]: With Titles Display [ON], the titles of [CH1 ~ 4] set on the Channel Title submenu by uses are displayed on the live screens.

  • Page 39: Record Setup

    4.5.2 RECORD SETUP . IMAGE SIZE : Set the resolution to either 720X480 or 360X240 4.5.3 CH1~CH4 Set the details of recording setup mode.
  • Page 40 MODE : Select one of four recording methods below. CONTINUOUS Continuous recording mode for 24h for day SCHEDULE Reserved recording MOTION DETECT Recording is activated when the system detects the motion from input video images. SENSOR Recording is activated when the system detects the sensor operation.

  • Page 41: System Setup

    M : Motion Detect recording - : Cancel the setting 4.6 SYSTEM SETUP This is a set up menu related to DVR system. Press the MENU button and select the Tab using the Left/Right button. Then, the submenu related to system appears as illustrated below. Press Button and select the submenu using the Left/Right button.

  • Page 42: Clock

    digit password using Up/Down and Right/Left button.. 4.6.3 CLOCK Set the date of the unit. . CLOCK : Set the time in this menu. The unit will automatically reboot for system stabilization . DATE MODE : Set the date format. Selects the date format among YY/MM/DD, MM/DD/YY, DD/MM/YY or YY-MM-DD, MM-DD-YY, DD-MM-YY .

  • Page 43: Network & Serial Setup

    . REMOTE CONTROLLER ID : Set the remote control ID. If you select 0, it appears R:A on the screen and user can control all the DVRs by using only one remote controller 4.7 NETWORK & SERIAL SETUP This is a set up menu related to Network and RS-485/422. Press the MENU button and select the Tab by using the Left/Right button.
  • Page 44 Step 1) user can set DDNS on the set up menu of SVR-440 as below. Select the Network menu and the following screen is displayed. Move the cursor on the DDNS SERVER and set it ON. This is all about the DDNS setup on the DVR unit.
  • Page 45 Procedure) Execution of the Dynamic IP authentication program Write MAC ADDRESS Click on the button confirm the authentication number!! Using GEN SERIAL, obtain the Registration number according to the Mac address Refer to the Mac address from the following path, DVR System setup-ETC-System info-MAC ADDRESS.
  • Page 46 Click Generate authentication number Input Mac Address Step 3) Move on to the DDNS registration server once the authentication number is generated. http://211.174.110.135 DDNS server -. (http://standalone4ch.com) 1. Register the ID and Password to be used for product registration. Input ID & Password and click on the OK button. Enter the ID &...
  • Page 47 Click..!! 3. Input Mac address, Registration and Domain name. Click on the CHECK button to move on next step. Click..!! 4. The following message will be displayed if the Domain name entered is usable.
  • Page 48 5. The following message will be displayed if the Domain name entered is not usable. 6. Click on button and then click on the OK button on Camera & Server registration screen. 7. Once the registration is done, Click on the LIST button on Camera & Server registration screen.
  • Page 49 9. Mac address can not be modified therefore Click on the DELETE button to delete the host name and repeat the registration procedure. Click..! 10. Click on the ‘YES’ button to delete the host name. Click..!!

  • Page 50: Client Access

    4.7.2 CLIENT ACCESS . PORT: When connecting to PC, the ports can be changeable. To connect SVR-440 to router, it needs to set all 3 kinds of ports. Default setting port on DVR: Control – Connect, ptz, event and other control data...

  • Page 51: Rs-485/422

    . MAIL SERVER IP: Please remain the default value. 4.7.4 RS-485/422 Set the connection details between monitoring devices and units. For example, set details between a camera and a CCTV. . SYSTEM ID: Set the IDs related to the DVR main unit ID in connecting devices such as cameras to the unit.

  • Page 52: Motion Detecttion

    4.8.1 MOTION DETECTTION CH1~4 [ON OFF] : Set whether to detect motions by channel. . Sensitivity : You can set the sensitivity to the changes on a screen from 1 to 9. Higher values mean more precise motion detection. . Area Setup : S elect the area for the motion detection in FULL or Partial zone. FULL ZONE : Detect motions by analyzing the changes of Full images from cameras.

  • Page 53: Sensor Type

    4.8.2 SENSOR TYPE Inputs detected and transferred from external sensors are identified as events. Select the switch type of a sensor connected to each channel. N/O : NORMAL OPEN Type Sensor N/C : NORMAL CLOSE Type Sensor 4.9 PTZ SETUP Press the MENU button and select the Tab using the Left/Right button.

  • Page 54: Exit Menu

    It is necessary to set the signals accurately by model. - Available Models Samsung : SPD(SPD-1600, SPD-2200, SPD-2500) PELCO(D) : PELCO ‘D’ Speed Dome using Protocol SRX : SRX-100B, DONGYANG, WON WOO, CANON, DYNACOLOR, SONY etc. 4.10 EXIT MENU Press the ESC button to close the menu after setup.

  • Page 55: Solution For Time Mismatch

    ④ Please create a folder at USB memory stick and name it “UPGRADE”. Copy the upgrade file into the folder and connect the USB memory stick to DVR. ⑤ Select the USB UPGRADE on the screen and the firmware upgrade aut omatically proceed.
  • Page 56 the screen as below) ③ Move the cursor to RTC Configuration and press ENT button. Following screen appears. ④ Input correct year/month/date/hour/min/sec and press ENT button. ⑤ Please pay attention to input correct time otherwise data stored in HDD can be deleted. ⑥...

  • Page 57: Chapter 5 Operations

    Chapter 5 Operations 5.1 Preliminary Checks before Starting Operation . Before Power up, be sure to check NTSC or PAL and select the right monitor out put between Composite and VGA by using the switch on the rear panel of the unit. See the details as below. Video mode Video output SETTING...

  • Page 58: Live Video Screen

    5.3 Live Video Screen After turning on power, the live video screen, the monitoring screen, is displayed. 5.3.1 Individual Channel and Split Screen Display Press the CH1 to CH4 buttons, and the video from each channel appears on the full screen. 5.3.1 Single and Multi Channel Display Press the Channel button[1~4], then the single channel is displayed on the full screen Press the ENT button, then the four connected channels are displayed on the quad split screens.

  • Page 59: Recording

    5.4 Recording 5.4.1 General Recording Press the REC button, then manual recording is immediately started and recording indication message will be displayed on the screen( ). Press the REC button again, then pre-setup recording will be activated according to the recording mode by each channel. Icon will be displayed as below : CONTINUOUS RECORDING : SENSOR RECORDING : MOTION RECORDING...

  • Page 60: Event Search

    5.5.1 EVENT SEARCH Select EVENT SEARCH and press ENT button to display below. . Date with blue color indicate that contains recorded data. . Select date, channel and event type and press PLAY button to playback. 5.5.2 TIME LINE BAR User can easily select a desired search time using the Time line bar.

  • Page 61: Go To

    5.5.3 GO TO User can enter a desired search date and time in this menu. Press ENT button to display as below. User can enter a desired search date and time and press PLAY button to playback. 5.5.4 GO FIRST Press ENT button to playback from the first data stored in the HDD.

  • Page 62: Copy List

    5.5.7 COPY LIST User can save the contents of HDD to USB memory stick for backup. Both of Still image and Video can be backup. Maximum backup time of Video is up to 999seconds. 5.5.7.1 Still image Backup ① During the monitoring, Press COPY button if you wish to capture image. When Figure1 is displayed, press YES to store the image into HDD and can be transferred to USB memory stick later.
  • Page 63 5.5.7.2 Video backup: Only available during Playback mode ① During the Playback, Press PAUSE button to pause the playback and Press COPY button. You will be asked whether to store Still image or Video(Figure1). Select Video and set the duration of copy to store the data into the HDD. ②...

  • Page 64: Recorded File Playback

    5.6 Recorded File Playback PLAY/PAUSE Playback and Pause the Playback screen Reverse playback. 1X, 2X, 4X Reverse Jump. The Playback position moves 1 minute backward. Forward Jump. The Playback position moves 1 minute forward Forward playback. 1X, 2X, 4X During playback, few frame can be missing depends on the image quality but this is not a defect of the unit.

  • Page 65: Initialize

    - For Focus adjustment, Press button 5.7.3 INITIALIZE : Select INITIALIZE and Press ENT button to initialize the PTZ camera. .Press the PTZ control button to move and press the button again to stop. The PTZ Mode is available in the Live Screen.

  • Page 66: Chapter 6 Network Viewer Program

    Chapter 6 Network Viewer Program Operates the unit or changes setting values on a remote PC by using the Network Viewer Program. This chapter describes the installation and operations of Network Viewer Program. This manual assumes that users are familiar with basic knowledge of the operation of O/S and computers.
  • Page 67 ⑥ Double-click the SvrManager.exe file to start the program. ⑦ The following screen is displayed. Minimize, Maximize, Exit button Time, IP information Connect./Dis-connect, Live/Playback, Password Channel Select, PTZ Control Recording status, Audio, Alarm...

  • Page 68: Control Panel For Live Screen

    6.2 Control Panel for Live screen ① Network Access ③ Password Input ② Recorded Data Search ④ Channel Select PTZ Control ⑥ ⑤ Auto Sequence HDD Free Space ⑦ ⑨ Audio Volume ⑧ Audio ON/OFF ⑩ Alarm Out...
  • Page 69 ① : Network Access Button The Network Viewer Program can perform the setting and operations through access to the units installed in up to four remote sites. To this end, the Network Viewer Program needs to be connected to the units installed in the remote places. Press button, and the following screen appears.
  • Page 70 ② : Recorded Data Search Button In Live monitoring mode, Press button, and following screen appears. You will be able to search data from the connected DVR. ③ : Password Input Box Press button, and the following screen appears. Input password and Press OK button to save the password.
  • Page 71 ⑧ : Audio ON/OFF button ⑨ : Audio Volume control. SVR-440 support Two-way Audio communication. Both of DVR site and client should have mike and speaker installed to use the function. ⑩ : Alarm When Alarm occurs on DVR, the color will turn to red.

  • Page 72: Control Panel For Live Screen

    6.3 Control Panel for Live screen ③ ① ② ④ ⑤ ① : Setup Menu for Network Viewer Press button, and the following screen appears. ①-1 General User can set Security option, Save path and Connect option in this Menu screen. Security Option : User can set the Password protection as below Startup : Password is required when you start the viewer.
  • Page 73 Search : Password is required when you the viewer turns to Search mode. Save Path Capture : Set the save path for the still image stored in the PC Backup : Set the save path for the still image stored in the PC Miscellaneous Automatic Reconnection : Automatic reconnection option when the line is disconnected.
  • Page 74 - LOG Path : Set save path for the Event Log file in the PC Size : Set size of folder for the Event Log file is stored. Setup whether Log, Icon and Event list are stored by Event type. Event Type ①-4 Record - Record Condition...
  • Page 75 Always + Auto record : While the Network is connected, Always store the images transmitted from the site. Event + Auto record : While the Network is connected, store the images transmitted from the site in case Event. - Event User can assign the desired Event type to be stored and the following screen box appears when you select Event on the Record Condition menu.
  • Page 76 Disk Space : Set the HDD space where the image is stored Disk Full Replace Oldest Files : The recorded data will be over written, when the HDD space is fully recorded. Stop Recording: Stop recording, even if the HDD space is fully recorded. ①-5 Video Set Brightness, Contrast, Hue and Saturation.
  • Page 77 ② : Still Image Capture button in Live mode Press button, and the following screen appears. Save Path : Press button on the Save path and set the desired save path. File Name : Write file name of the image to be stored File Format : Select save file format.
  • Page 78 : Press the button once again to stop the recording : Press the button to disconnect the network : Press the button to convert to play mode screen The calendar shows dates with recorded video in red. Select the date on the calendar you wish to play The green bar indicates there is recorded videos on the date which is selected.

  • Page 79: Control Panel For Search Screen

    6.4 control Panel for Search screen ① Password Input ③ ② Network Access Recorded Data Search ④ Channel Select Search Calendar ⑤ ⑥ HDD Free Space ⑦ ⑧ Audio Volume ⑨ Alarm out Audio ON/OFF ⑩ Playback Button ① : Network Access Button...
  • Page 80 Network connect button and refer to Control panel for Live screen for Network access button. ② : Recorded Data Search Button In Search screen mode, Press button to switch into Live monitoring mode. ③ : Password Input Box Press button, and the following screen appears. Input password and Press OK button to save the password.

  • Page 81: Other Search Button

    6.5 Other Search Button ① ② ③ ④ ⑤ ⑥ ① : Still Image Capture button in Search mode In Search mode, Press button, and the following screen appears. Save Path : Press button on the Save path and set the desired save path. File Name : Write file name of the image to be stored.

  • Page 82: Search

    ④ : Mark out After press the Mark in button, Press button to mark out as a end time for the backup. Between Mark in and Mark out time will be indicated in Purple color. Once you set the Mark in & out, Press button and press OK button to start backup.

  • Page 83: Chapter 7 Troubleshooting

    Chapter 7 Troubleshooting The SVR-440 is a very sophisticate device, so failure can occur. For failures, please follow the instructions described below. The unit will not turn on even after plugging the adaptor jack. * Check whether the power cord is properly plugged in.
  • Page 84 SVR- - - - 440 4CH Digital Video Recorder Digital Video Recorder Digital Video Recorder Digital Video Recorder Specifications Specifications Specifications Specifications Video Input 4 BNC Monitor Output 1BNC, 1VGA(Selectable) Compression MPEG4 Speed 120fps 100fps Display Resolution 720 X 480 720 X 576 Multi Screen Speed...

Table of Contents