Sony MZ-R909 Service Manual page 29

[VOL+]
156. Adjust with the
key (adjusted value down) so that the adjusted value becomes
F0.
Remote commander LCD display
023 1041F0
F0 : Adjusted value
157. Press the key.
X
(1041 is blinking)
[VOL+]
158. Press the key once to change the blinking portion to
1042.
Remote commander LCD display
023 104200
00 : Adjusted value
159. Press the x key.
(00 is blinking)
[VOL+]
160. Adjust with the
key (adjusted value down) so that the adjusted value becomes
B0.
Remote commander LCD display
023 1042B0
B0 : Adjusted value
161. Press the key.
X
(1042 is blinking)
[VOL+]
162. Press the key once to change the blinking portion to
1043.
Remote commander LCD display
023 104300
00 : Adjusted value
163. Press the x key.
(00 is blinking)
[VOL+]
164. Adjust with the
key (adjusted value down) so that the adjusted value becomes
E1.
Remote commander LCD display
023 1043E1
E1 : Adjusted value
165. Press the key.
X
(1043 is blinking)
[VOL+]
166. Press the key twice to change the blinking portion to
1045.
Remote commander LCD display
023 104500
00 : Adjusted value
167. Press the key.
x
(00 is blinking)
[VOL+]
168. Adjust with the
key (adjusted value down) so that the adjusted value becomes
B0.
Remote commander LCD display
023 1045B0
B0 : Adjusted value
169. Press the X key.
(1045 is blinking)
[VOL--]
key (adjusted value up) or
[VOL--]
key (adjusted value up) or
[VOL--]
key (adjusted value up) or
[VOL--]
key (adjusted value up) or
[VOL+]
170. Press the key twice to change the blinking portion to
1047.
Remote commander LCD display
023 104700
00 : Adjusted value
171. Press the key.
x
(00 is blinking)
[VOL+]
172. Adjust with the
key (adjusted value down) so that the adjusted value becomes
03.
Remote commander LCD display
023 104703
03 : Adjusted value
173. Press the X key.
(1047 is blinking)
[DISPLAY]
174. Press the key on the remote commander for sev-
eral seconds (about 3 seconds) to exit the patch data write
mode and display as below.
Remote commander LCD display
023 Patch0A
0A : Adjusted value
175. Press the key to write the modified data.
X
176. The modified data writing is over, if the adjusted value
changes to DD.
Remote commander LCD display
023 ***SDD
DD : Adjusted value
177. Turn the power off.
• Modified data writing method (version 2.000)
1. Select the manual mode of the test mode, and set item number
022 (see page 13).
Remote commander LCD display
022 PatClr CC
2. Press the key to initialize the patch data.
X
(The modified data writing is over, if the adjusted value changes
to DD)
Remote commander LCD display
022 ***SDD
DD : Adjusted value
3. Press the key or
N >
Remote commander LCD display
023 Patch00
00 : Adjusted value
[VOL+]
4. Press the key once to change the adjusted value to 01.
[DISPLAY]
5. Press the key on the remote commander for sev-
eral seconds (about 3 seconds) to activate the patch data write
mode.
(The following display will appear where 00 is blinking)
Remote commander LCD display
023 102800
00 : Adjusted value
MZ-R909
[VOL--]
key (adjusted value up) or
key to set item number 023.
29