NAD M17 Owner's Manual page 9

Below is a table of sample combination settings with respect to
switching ON the M17 from standby mode and vice versa.
+12V +12V
AUTO
TRIGGER IN TRIGGER(IN)
TRIGGER IN
(OFF/AUTO) (item 5)
AUTO +12V Main, All
AUTO +12V Main, All
AUTO 0V Main, All
AUTO 0V Zone 2,
Zone 3 or
Zone 4
AUTO 0V Zone 2,
Zone 3 or
Zone 4
OFF +12V Any
or 0V setting
OFF +12V Any
or 0V setting
4 IR IN/IR OUT 1-4
These mini-jacks accept and output remote-controlled codes in
electrical format, using industry-standard protocols, for use with "IR-
repeater" and multi-room systems and related technologies.
• All NAD products with IR IN/IR OUT features are fully compatible
with the M17. For non-NAD models, please check with your other
product's service specialists with respect to their compatibility to
the M17's IR features.
IR IN
• This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another compatible device
to allow control of the M17 from a remote location.
IR OUT 1- 4
• Connect IR OUT 1 (or IR OUT 2/IR OUT 3/IR OUT 4) to the IR IN jack of
a compatible device.
• Command and control the linked compatible device by directing its
own remote control to M17's infrared receiver.
IR IN and IR OUT 1/IR OUT 2/IR OUT 3/IR OUT 4
•
Connect the M17's IR IN to the IR OUT of a compatible device.
Connect also the M17's IR OUT 1 (or IR OUT 2/IR OUT 3/IR OUT 4) to
the IR IN of a compatible device.
• With this setup, the M17 acts as an "IR-repeater" allowing the device
connected to the M17' s IR IN control or command of the other
device linked to M17's IR OUT 1 (or IR OUT 2/IR OUT 3/IR OUT 4).
FRONT
HTRM 2 (ON/ M17 POWER
PANEL
OFF) MODE STATE
o (STANDBY)
ON ON Operating
mode
OFF OFF Operating
mode
ON/OFF ON/OFF Standby
mode
ON ON Operating
mode
OFF OFF Standby
mode
ON ON Operating
mode
OFF OFF Standby
mode
IDENTIFICATION OF CONTROLS
5 +12V TRIGGER OUT1/OUT2/OUT3
The M17 has three +12V TRIGGER OUT ports (OUT 1, OUT2 and OUT3)
that can be configured to supply +12V DC to a linked component or
system. See discussion on "Trigger Setup" at the "Setup Menu" literature
for guidelines on how to configure +12V TRIGGER IN/OUT.
• Use a 3.5mm mini-jack connector to pass +12 volts at a maximum
current of 50 milliamps to an auxiliary equipment such as a
multichannel amplifier or subwoofer. The center conductor (hot) of
the 3.5mm jack is the control signal. The outside conductor (shield)
is the ground return-path.
• This output will be 12V when the M17 is ON and 0V when the unit is
either OFF or in standby mode.
+12V TRIGGER IN
With this input triggered by a 12V DC supply, the M17 can be switched
ON remotely from standby mode by compatible devices such as
amplifiers, preamplifiers, receivers, etc. If the 12V DC supply is cut off,
the M17 will return to standby mode.
•
Connect this +12V TRIGGER INPUT to the remote device's
corresponding +12V DC output jack using a mono cable with
3.5mm male plug. The controlling device must be equipped with a
+12V trigger output to use this feature.
6 AUDIO 1-7 IN/VIDEO INPUT 1-3
• These comprise the M17's other sets of principal input. Connect
these audio and video input ports to corresponding output ports of
compatible source components such as DVD players, CD players or
cable/satellite boxes.
• AUDIO 5 IN, AUDIO 6 IN and AUDIO 7 IN are ideal for the connection
of the analog output of line-level audio sources like a CD player or
Stereo tuner.
•
The Left Channel of AUDIO 1 IN is the assigned port where the
supplied 3.5mm female jack to RCA plug Adapter can be connected.
Plug in the Audyssey microphone into the adapter for Audyssey
Auto Calibration.
AUDIO 3-4 OUT/VIDEO OUT
• Connect AUDIO 3 OUT (and/or AUDIO 4 OUT) to corresponding
recording components or audio/video input ports of compatible
sources like cassette deck, CD/DVD recorder or outboard audio
processors.
• The signal present at AUDIO 3 OUT is determined by the current
source selected. There will be no output at AUDIO 3 OUT when
AUDIO 3 is selected. Likewise, there will be no output at AUDIO
4 OUT when AUDIO 4 is the active source input. This prevents
feedback through the recording component thereby preventing
possible damage to your speakers.
•
When configured, AUDIO 3 OUT and AUDIO 4 OUT are the same
assigned ports for Zone 3 and Zone 4 respectively. See also Zone
output description below.
7 COMPONENT VIDEO INPUT 1-2,
COMPONENT VIDEO MONITOR OUT
• Connect the Component Video Input to Component Video output
of compatible source components, typically a DVD player, BD
player, digital cable box or other applicable components. Connect
Component Video Monitor Out to the Component Video input of a
compatible video monitor/TV.
•
Be sure to observe consistency in connecting the Y/Pb/Pr jacks
to the corresponding sources/inputs. The routing of the two
component video input is fully configurable via the Source Setup
item of the Setup Menu OSD.
• The M17's sets of component video input and output are fully
wideband and compatible with allowable HDTV formats.
REAR PANEL
9