Table of Contents
Advertisement
IDENTIFICATION OF CONTROLS
REAR PANEL
R
L
R
FRONT
SURR
IN
IN
IN
OUT
IN
OUT
L
ZONE 3
ZONE 4
R
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
COMPONENT VIDEO INPUT 1
Y
C
B
/P
B
1
2
3
VIDEO INPUT
COMPONENT VIDEO INPUT 2
VIDEO OUT
6
7
ATTENTION!
Please make sure that the M17 is powered off or unplugged from the mains power source before making any connections. It is also advisable to power
down or unplug all associated components while making or breaking any signal or AC power connections.
1 AUDIO PRE-OUT (BALANCED)
•
The AUDIO PRE-OUT makes it possible to use the M17 as a pre-
amplifier to external power amplifiers for some or all channels.
•
Depending upon the source's configuration, analog audio
output connection can be made up to seven channels either via
BALANCED or SINGLE-ENDED output ports.
•
Use the AUDIO PRE OUT (BALANCED) if the external source to be
connected has BALANCED audio input. Superior audio quality
is ensured with the distinctive noise reduction capability of
BALANCED connection with XLR jacks.
•
Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and
SURR-BR to the respective channel input of a power amplifier or
amplifiers driving the corresponding applicable speakers.
•
Connect the SUBW output to powered ("active") subwoofers or to
power amplifier channels driving a passive system.
AUDIO PRE OUT (SINGLE-ENDED)
•
Use single-ended AUDIO PRE OUT for sources that are not equipped
with BALANCED analog audio input.
2 RS 232
NAD is a certified partner of AMX and Crestron and fully supports
these external devices. Check out the NAD website for information
about AMX and Crestron compatibility with NAD. See your NAD audio
specialist for more information.
•
Connect this interface using RS-232 serial cable (not supplied) to
any Windows compatible PC to allow remote control of the M17 via
compatible external controllers.
•
Refer to the NAD website for information about RS232 Protocol
documents and PC interface program.
8
AUDIO PRE-OUT BALANCED
L
R
L
SURR-B
CENTER
SUBW
IN
IN
IN
OUT
DIGITAL AUDIO IN
2
1
4
3
COAXIAL IN
AUDIO 5
AUDIO 6 AUDIO 7
ZONE 2
MONITOR OUT
ZONE 2
C
R
/P
R
Y
C
/P
C
/P
B
B
R
R
MONITOR OUT 1 MONITOR OUT 2
MONITOR OUT
8
9
10 11
1
2
AUDIO PRE-OUT
CENTER
L
L
R
R
SUBW1
FRONT
SURR
SURR-B
SUBW2
DIGITAL AUDIO OUT
1
1
2
3
4
1
2
2
OPTICAL IN
COAXIAL OUT
OPTICAL OUT
LAN
HDMI 4
HDMI 5
HDMI 6
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
HDMI 1
HDMI 2
HDMI 3
12
3 +12V TRIGGER IN (OFF/AUTO)
•
The settings of +12V TRIGGER IN (OFF/AUTO) together with +12V
TRIGGER (IN) (item 5) affect the manner on how the M17 can be
switched ON from standby mode or back to standby mode.
+12V TRIGGER IN (AUTO)
•
If +12V TRIGGER IN (OFF/AUTO) is set to AUTO, pressing the front
panel o (Standby) button or HTRM 2's ON/OFF button cannot
switch ON the M17 from standby mode and vice-versa. Both
control buttons are effectively disabled thereby handling the
function of powering up the M17 to an external controller.
•
If +12V TRIGGER IN (OFF/AUTO) is set to AUTO, powering up the
M17 is dependent upon the "Auto Trigger In" setting at the "Trigger
Setup" menu as well as the absence or presence of +12V at +12V
TRIGGER (IN)(item 5).
+12V TRIGGER IN (OFF)
•
Slide the +12V TRIGGER IN (OFF/AUTO) switch to OFF for the M17 to
be normally switched ON from standby mode and vice-versa using
the front panel o (Standby) button or HTRM 2's ON/OFF button.
•
The +12V TRIGGER (IN) (item 5) is disabled with +12V TRIGGER IN
(OFF/AUTO) set to OFF.
3
4
5
+12V TRIGGER
IR
OUT 1
OUT 2
OUT 1
OUT 2
+12V TRIGGER IN
OFF
AUTO
RS232
IN
IN
OUT 3
OUT 4
OUT 3
POWER
ON
120V~60Hz
UNSWITCHED AC OUTLET
120V~60Hz 120W 1A MAX
© NAD M17
13
14
15
Hide quick links:
Advertisement
Table of Contents
