Table of Contents
Advertisement
OPERATION
USING THE HTRM 2 REMOTE CONTROL
Example: Record a Macro to the [0] key to Turn on the M17, Select "Input 1"
(Source 1), and Commence Playback of connected Source 1 device (as in
BD player):
•
On the HTRM 2, simultaneously press-and-hold [MACRO] and
[0] (numeric zero); the Learn LED turns steady green.
•
Press [AMP]; press [ON]; press [1] ("Input or Source 1"); press [BD];
press [4] (Play) - the Learn LED blinks as each step is added.
•
Press [MACRO] again to exit the macro-record mode.
To clear a macro, perform the above steps without entering any functions.
EXECUTING MACROS
To execute a macro, press and release [MACRO]; its key illumination lights
for 5 seconds. While it remains lit, press an HTRM 2 key to which a macro
has previously been stored.
The corresponding macro will run; as each step executes, its "parent" Device
Selector's key flashes lights briefly; when execution is finished, the [MACRO]
key illumination goes out. Pressing any other HTRM 2 key while a macro is
executing will abort the macro. Remember that you must hold the HTRM 2
so that its infrared emitter can activate the target components.
NOTE
When a macro executes, a 1 second delay is automatically inserted
between its commands. If you need more than a 1 second delay between
particular commands—for example, to permit a component to power
up completely—you can record "empty" steps into the macro by
changing Device Selector "pages" without entering actual command
functions.
KEY ILLUMINATION TIMEOUT
The HTRM 2's key-illumination can be set to remain lit for 0-9 seconds. The
default value is 2 seconds. To set the illumination timeout, simultaneously
press-and-hold for 3 seconds both the HTRM 2's [DISP] and the [0-9] key,
with the digit corresponding to the desired timeout duration; the Learn
LED will flash twice to confirm the new setting. When set to zero, the
illumination will not turn on at all.
NOTES
•
Key illumination is activated when one presses any HTRM 2 key.
•
If HTRM 2 senses movement, key illumination is activated without
having to press a key. If HTRM 2 is shaken, key illumination is also
activated.
•
Key illumination is the biggest drain on the HTRM 2's batteries. A short
key illumination timeout will extend battery life appreciably; turning it
off altogether (set it to 0 seconds) will lengthen it still further.
CONFIGURING KEY ILLUMINATION
Keys to Press (for 3 seconds)
Mode
DISP + Digit Key (0-9)
Set key illumination timeout to number of
seconds corresponding to digit key. Zero turns off
the key illumination entirely.
DISP + OFF
Disable light sensor. Key illumination will turn
on with any key press.
DISP + ON
Enable light sensor.
DISP + ENTER
Set the light sensor threshold to the current
light level.
DISP + RTN
Restore all key illumination settings to the
defaults.
32
FACTORY RESET
The HTRM 2 can be reset to its factory state, deleting all learned commands,
copied and punched-through keys, macros, and other setup information,
reverting all keys to their pre-programmed library commands.
To perform a factory reset simultaneously press-and-hold for 10 seconds
the HTRM 2's [ON] and [RTN] keys; the Learn LED will start to flash green.
Release [ON] and [RTN] before the second flash is complete; the Learn LED
will turn red, indicating the remote has been reset.
NOTE
You must release [ON] and [RTN] before the second flash goes out,
otherwise the unit will not reset; should this occur, repeat the full
procedure.
DELETE MODE
The HTRM 2 can store learned, copied, and "default library" commands on
any single key (The default library commands are the pre-programmed
NAD codes, such as the native M17 commands on the [AMP] "page. " ).
You can delete commands by layers back "down" to the default library
command on any key, removing learned commands, punched-through
functions, and copied keys.
NOTE
The default library commands cannot be deleted, so you need not worry
that using Delete Mode might cause irreparable changes.
To enter Delete Mode, simultaneously press-and-hold for 3 seconds both
the desired key's Device Selector key and the [RTN] key, until the Learn LED
turns green. Press the function key whose command you wish to delete;
the Learn LED flashes; the number of times indicates which type of function
has become active - see the table below. Press the active Device Selector
key again to exit Delete Mode.
NOTE
You may delete multiple function-key commands on the same Device
Selector "page, " but to delete from more than one Device Selector page
you must exit Delete Mode and then re-enter it on the required page.
Flashes
Command Type
1
Default Library Command
2
Copied Library Command
3
Learned Command
Hide quick links:
Advertisement
Table of Contents
