Advertisement
I N S TA L L AT I O N & U S E R I N S T R U C T I O N S
Section
Contents
1.0
Important Notes
2.0
Installation Requirements
3.0
Appliance Data
4.0
Unpacking the Appliance
5.0
Component Checklist
6.0
Operating the Appliance
1.0 IMPORTANT NOTES
• DO NOT use this appliance immediately below a fixed socket outlet.
• DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture
could present a hazard.
• DO NOT allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or sim-
ilar material. A clearance space of at least one metre must be allowed in front of the appliance. A clearance space of 100mm each
side must be allowed. A clearance space of 50mm must be allowed for the back of the appliance.
• CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device
that will switch on the appliance automatically, as a fire risk may occur if the heater is accidentally covered or displaced.
• The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly in front of the
heater unit.
• If the cord is damaged, it must be replaced by a service agent or competent person.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
2.0 INSTALLATION REQUIREMENTS
The appliance is supplied with a pre-wired three pin BS1363 plug plug (13Amp fuse rated) and 1.6 metres of electrical flex. It is
therefore necessary for a suitable electrical socket to be located within this distance of the appliance and be easily accessible. The
stove may be installed on a combustible or non-combustible floor, however the heater outlet is underneath the stove and certain
types of floor covering may be affected by the heat produced by the stove. The ability of the floor covering to withstand the heat
produced by the stove should be ascertained before proceeding with the installation of the stove. If in doubt then the stove should
be mounted on a non-combustible hearth or plinth which extends for at least 150mm in front of the stove.
This appliance should be positioned on a firm level surface. If the stove is to be sited in a fire surround then the suitability of the
surround for use with electrical heaters should be established with the fire surround manufacturer.
If fitted into an open draught fireplace, it is advisable to block off the chimney to reduce the risk of draught through the stove
which may cause the safety cut out system in the fan heater to operate.
3.0 APPLIANCE DATA
Supply Voltage :
Heating Elements :
Location :
4.0 UNPACKING THE APPLIANCE
Read all the instructions before continuing to unpack or install this appliance. Carefully lift the appliance from the carton. Check
that the contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling
centre.
5.0 COMPONENT CHECKLIST
QUANTITY
1
1
Page No.
2
2
2
2
2
3
230-240v~50Hz
2 x 900W
Indoor use only
DESCRIPTION
Heater
User instruction booklet
Section
Contents
7.0
Safety Cut-Out System
8.0
Maintenance
9.0
Cleaning
10.0
Spares
11.0
Servicing
12.0
Appliance Dimensions
Fuse Rating :
Lighting :
Supply plug/cord :
2
GB IE
Page No.
3
3
3
3
4
4
13 Amp
2 x 25W E14 bulb
BS1363/1.6 metres length
©
©
2011 Focal Point Fires plc.
2011 Focal Point Fires plc.
Advertisement
